10:37:32 - Resetting NMC
10:37:41 - Starting task "Configure modules"
10:37:41 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.6.0-41551 
10:37:41 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.6.0-41551 
10:37:41 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.6.0-41551 
10:37:41 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.6.0-41551
10:37:41 - Configuring modules with configuration /data/config/2021/20211011/config_cameraqm_265febs_newHV5.NMC.xml
10:37:41 - Switching off high voltages in configuration
10:37:51 - Successfully configured 265 module(s)
10:37:51 - Waiting for modules to be configured...
10:37:57 - All front-end boards are programmed with firmware F56D2002
10:38:10 - Found 2 different versions of DTBP firmware: [15 17]
10:39:10 - NMC is in state NmcState.Ready and knows of 265 drawer(s)
10:39:33 - All front-end boards have counted 0 event(s)
10:39:41 - Found 0 PPS errors.
10:39:41 - Finished task "Configure modules"
10:41:58 - Starting task "Switch HVPA voltage state"
10:41:58 - Setting HVPA current limit to 12489.75 uA
10:41:58 - Setting Hvpa.Hvpa0.CurrentTrip in all drawers
10:42:13 - Setting Hvpa.Hvpa1.CurrentTrip in all drawers
10:42:29 - Setting Hvpa.Hvpa2.CurrentTrip in all drawers
10:42:44 - Setting Hvpa.Hvpa3.CurrentTrip in all drawers
10:42:59 - Setting Hvpa.Hvpa4.CurrentTrip in all drawers
10:43:14 - Setting Hvpa.Hvpa5.CurrentTrip in all drawers
10:43:29 - Setting Hvpa.Hvpa6.CurrentTrip in all drawers
10:43:45 - Setting HVPA ramp speed to 25 V/s
10:44:02 - Switching HVPA to state Nominal
10:44:34 - Setting HVPA current limits...
10:46:33 - Finished task "Switch HVPA voltage state"
10:49:05 - High voltage locked channels will be checked every 60 s
10:49:08 - Starting NMC
10:49:08 - Clearing PPS error counters
10:49:30 - Resetting FEB counters...
10:49:36 - Starting all configured modules...
10:50:05 - Checking for high voltage locked pixels...
10:50:30 - HVPA channel 2 of drawer 86 has status 0x0007!
10:50:30 - HVPA channel 2 in module 86 is in rise default!
10:50:54 - HVPA channel 6 in module 73 is still in progress
10:50:54 - HV is locked in 0 channel(s), was in rise default in 1 channel(s) and was still in progress in 2 channel(s)
10:51:05 - Checking for high voltage locked pixels...
10:51:30 - HVPA channel 2 of drawer 86 has status 0x0007!
10:51:30 - HVPA channel 2 in module 86 is in rise default!
10:51:54 - HVPA channel 6 in module 73 is still in progress
10:51:54 - HV is locked in 0 channel(s), was in rise default in 1 channel(s) and was still in progress in 2 channel(s)
10:52:05 - Checking for high voltage locked pixels...
10:52:18 - HVPA channel 0 in module 117 is still in progress
10:52:30 - HVPA channel 2 of drawer 86 has status 0x0007!
10:52:30 - HVPA channel 2 in module 86 is in rise default!
10:52:36 - HVPA channel 3 in module 23 is still in progress
10:52:54 - HV is locked in 0 channel(s), was in rise default in 1 channel(s) and was still in progress in 3 channel(s)
10:53:05 - Checking for high voltage locked pixels...
10:53:30 - HVPA channel 2 of drawer 86 has status 0x0007!
10:53:30 - HVPA channel 2 in module 86 is in rise default!
10:53:36 - HVPA channel 3 in module 23 is still in progress
10:53:47 - HVPA channel 5 in module 38 is still in progress
10:53:54 - HV is locked in 0 channel(s), was in rise default in 1 channel(s) and was still in progress in 3 channel(s)
10:54:05 - Checking for high voltage locked pixels...
10:54:30 - HVPA channel 2 of drawer 86 has status 0x0007!
10:54:30 - HVPA channel 2 in module 86 is in rise default!
10:54:36 - HVPA channel 3 in module 23 is still in progress
10:54:48 - HVPA channel 5 in module 133 is still in progress
10:54:54 - HVPA channel 6 in module 73 is still in progress
10:54:54 - HV is locked in 0 channel(s), was in rise default in 1 channel(s) and was still in progress in 4 channel(s)
10:55:01 - Stopped periodic check of locked high voltages
10:55:03 - Calling method FSM.gotoObserving in object FSM
10:55:03 - Starting run 2678
10:55:09 - Updating voltage widget...
10:55:53 - High voltage locked channels will be checked every 60 s
10:56:54 - Checking for high voltage locked pixels...
10:57:19 - HVPA channel 2 of drawer 86 has status 0x0007!
10:57:19 - HVPA channel 2 in module 86 is in rise default!
10:57:36 - HVPA channel 5 in module 38 is still in progress
10:57:42 - HVPA channel 6 in module 73 is still in progress
10:57:42 - HV is locked in 0 channel(s), was in rise default in 1 channel(s) and was still in progress in 3 channel(s)
10:57:50 - Stopped periodic check of locked high voltages
10:57:55 - Checking UCTS clock...
10:57:56 - UCTS clock is late by 10 seconds!
10:57:56 - Configuring UCTS with (10.200.7.250, 10.200.4.100, 44:a8:42:44:32:c9)
10:57:56 - Configuring TIB...
10:57:56 - Setting TIB forced mode to False
10:57:56 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:57:56 - Status: TibState.PpsStopped
10:57:56 - Alarms: AlarmVector.ReadError
10:57:56 - Connection status: False TXclient_alive: False
10:57:56 - Entering set_external_delay
10:57:56 - Setting ExternalDelayLocal to 27.000 ns
10:57:56 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:57:57 - Entering set_external_delay
10:57:57 - Setting ExternalDelayCalibration to 58.000 ns
10:57:57 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:57:57 - Entering set_external_delay
10:57:57 - Setting ExternalDelaySphe to 110.000 ns
10:57:57 - Writing 110.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:57:57 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:57:57 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:57:57 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:57:57 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:57:57 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:57:57 - Writing True to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:57:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:57:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:57:57 - Status: TibState.PpsStopped
10:57:57 - Alarms: AlarmVector.ReadError
10:57:57 - Connection status: False TXclient_alive: False
10:57:57 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:57:57 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:57:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:57:57 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:57:57 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:57:57 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:57:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:57:57 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:57:57 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:57:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:57:58 - Connecting TIB to camera server at 10.10.4.12:222
10:57:58 - Starting TIB...
10:57:58 - Status: TibState.PpsStopped
10:57:58 - Alarms: AlarmVector.ReadError
10:57:58 - Connection status: False TXclient_alive: True
10:57:58 - Resetting run
10:57:58 - Wait for UCTS external trigger before enabling trigger...
10:57:58 - Status: TibState.Standby
10:57:59 - Alarms: AlarmVector.NoAlarm
10:57:59 - Connection status: False TXclient_alive: True
10:57:59 - Status: TibState.Standby
10:57:59 - Alarms: AlarmVector.NoAlarm
10:57:59 - Connection status: False TXclient_alive: True
10:58:00 - Status: TibState.Armed
10:58:00 - Alarms: AlarmVector.NoAlarm
10:58:00 - Connection status: True TXclient_alive: True
10:58:01 - Starting TIB triggers...
10:58:01 - Enabling trigger
10:58:01 - Status: TibState.Running
10:58:01 - Alarms: AlarmVector.NoAlarm
10:58:01 - Connection status: True TXclient_alive: True
10:58:05 - Configuring calibration box...
10:58:05 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=500 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
10:58:06 - Starting flashes...
10:59:05 - Stopping TIB...
10:59:05 - Status: TibState.Running
10:59:05 - Alarms: AlarmVector.ReadError
10:59:05 - Connection status: True TXclient_alive: True
10:59:05 - Disabling trigger
10:59:05 - Disabling PPS
10:59:06 - Status: TibState.PpsStopped
10:59:06 - Alarms: AlarmVector.ReadError
10:59:06 - Connection status: True TXclient_alive: True
10:59:07 - Closing TIB connection to camera server
10:59:08 - Status: TibState.PpsStopped
10:59:08 - Alarms: AlarmVector.ReadError
10:59:08 - Connection status: False TXclient_alive: False
10:59:08 - Run duration: 0:01:05
10:59:08 - Local camera triggers: 0
10:59:08 - Slow control triggers: 0
10:59:08 - Single photo-electron triggers: 0
10:59:08 - Calibration triggers: 49962
10:59:08 - Software triggers from UCTS: 0
10:59:08 - Pedestal triggers: 0
10:59:08 - Collected input triggers: 49962
10:59:08 - Busy triggers: 0
10:59:08 - Camera event triggers sent to clusters: 49962
10:59:10 - Calling method FSM.gotoReady in object FSM
10:59:14 - Stopping NMC
10:59:21 - Found 0 PPS errors.