16:03:47 - Checking for high voltage locked pixels...
16:03:53 - Updating voltage widget...
16:03:59 - Starting task "Configure modules"
16:03:59 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
16:03:59 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
16:03:59 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
16:03:59 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
16:03:59 - Configuring modules with configuration /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy4_nd681.NMC.xml
16:03:59 - Switching off high voltages in configuration
16:04:03 - Successfully configured 2 module(s)
16:04:03 - All front-end boards are programmed with firmware 61210216
16:04:03 - All backplanes are programmed with firmware 15
16:04:04 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:04:04 - Found 0 PPS errors.
16:04:04 - Finished task "Configure modules"
16:04:07 - Starting task "Switch HVPA voltage state"
16:04:07 - Setting HVPA current limit to 12489.75 uA
16:04:08 - Setting HVPA ramp speed to 25 V/s
16:04:08 - Switching HVPA to state Nominal
16:04:15 - Setting HVPA current limits...
16:04:16 - Finished task "Switch HVPA voltage state"
16:04:17 - Checking for high voltage locked pixels...
16:04:28 - Checking status of calibration box...
16:04:29 - Calibration box is configured with 0 leds at a frequency of 10.0 Hz and a voltage of 10.49 V
16:04:47 - Checking for high voltage locked pixels...
16:05:10 - Starting task "Check high voltages"
16:05:10 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:05:10 - Actual voltage is between 984.54 V and 1117.52 V.
16:05:11 - Low voltages range between 300.00 V and 300.00 V. 
16:05:11 - Reference voltages range between 984.98 V and 1117.51 V. 
16:05:11 - Maximum difference between expected and actual voltages is 0.45 V
16:05:12 - Maximum of current limits is 4840.96 uA
16:05:12 - Checking status of HVPA module in 2 drawer(s)...
16:05:12 - Checking status of HVPA channels in 2 drawer(s)...
16:05:12 - HV is stabilized in all channels.
16:05:12 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy4_nd681.NMC.xml
16:05:12 - Done
16:05:13 - Finished task "Check high voltages"
16:05:16 - Starting NMC
16:05:16 - Clearing PPS error counters
16:05:17 - Checking for high voltage locked pixels...
16:05:47 - Checking for high voltage locked pixels...
16:05:51 - Calling method FSM.gotoReady in object FSM
16:05:58 - Calling method FSM.gotoObserving in object FSM
16:06:17 - Checking for high voltage locked pixels...
16:06:26 - Checking UCTS clock...
16:06:26 - UCTS clock is late by 12 seconds!
16:06:26 - Configuring UCTS
16:06:26 - Configuring TIB...
16:06:26 - Setting TIB forced mode to False
16:06:26 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:06:26 - Status: TibState.PpsStopped
16:06:26 - Alarms: AlarmVector.BufferFull|AlmostFull
16:06:26 - Connection status: False TXclient_alive: False
16:06:26 - Entering set_external_delay
16:06:26 - Setting ExternalDelayLocal to 27.000 ns
16:06:26 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:06:27 - Entering set_external_delay
16:06:27 - Setting ExternalDelayCalibration to 58.000 ns
16:06:27 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:06:27 - Entering set_external_delay
16:06:27 - Setting ExternalDelaySphe to 150.000 ns
16:06:27 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:06:27 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
16:06:27 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:06:27 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:06:27 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:06:27 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:06:27 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:06:27 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:06:27 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:06:27 - Status: TibState.PpsStopped
16:06:27 - Alarms: AlarmVector.BufferFull|AlmostFull
16:06:27 - Connection status: False TXclient_alive: False
16:06:27 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:06:27 - Writing 5000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:06:27 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:06:27 - Writing True to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:06:27 - Writing 5000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:06:27 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:06:27 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:06:27 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:06:27 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:06:27 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:06:28 - Connecting TIB to camera server at 10.10.4.12:222
16:06:29 - Starting TIB...
16:06:29 - Status: TibState.PpsStopped
16:06:29 - Alarms: AlarmVector.BufferFull|AlmostFull
16:06:29 - Connection status: False TXclient_alive: False
16:06:29 - Resetting run
16:06:29 - Wait for UCTS external trigger before enabling trigger...
16:06:29 - Status: TibState.Standby
16:06:29 - Alarms: AlarmVector.NoAlarm
16:06:29 - Connection status: False TXclient_alive: True
16:06:29 - Status: TibState.Standby
16:06:29 - Alarms: AlarmVector.NoAlarm
16:06:29 - Connection status: False TXclient_alive: True
16:06:30 - Status: TibState.Armed
16:06:30 - Alarms: AlarmVector.NoAlarm
16:06:30 - Connection status: False TXclient_alive: True
16:06:32 - Starting TIB triggers...
16:06:32 - Enabling trigger
16:06:32 - Status: TibState.Running
16:06:32 - Alarms: AlarmVector.NoAlarm
16:06:32 - Connection status: False TXclient_alive: True
16:06:47 - Checking for high voltage locked pixels...
16:07:03 - Stopping TIB...
16:07:03 - Status: TibState.Running
16:07:03 - Alarms: AlarmVector.BufferFull|AlmostFull
16:07:03 - Connection status: False TXclient_alive: True
16:07:03 - Disabling trigger
16:07:04 - Disabling PPS
16:07:05 - Status: TibState.PpsStopped
16:07:05 - Alarms: AlarmVector.BufferFull|AlmostFull
16:07:05 - Connection status: False TXclient_alive: True
16:07:05 - Closing TIB connection to camera server
16:07:06 - Status: TibState.PpsStopped
16:07:06 - Alarms: AlarmVector.BufferFull|AlmostFull
16:07:06 - Connection status: False TXclient_alive: False
16:07:06 - Run duration: 0:00:34
16:07:06 - Local camera triggers: 0
16:07:06 - Slow control triggers: 0
16:07:06 - Single photo-electron triggers: 16
16:07:06 - Calibration triggers: 9
16:07:06 - Software triggers from UCTS: 0
16:07:06 - Pedestal triggers: 218070
16:07:06 - Collected input triggers: 205375
16:07:06 - Busy triggers: 140
16:07:06 - Camera event triggers sent to clusters: 205235
16:07:08 - Calling method FSM.gotoReady in object FSM
16:07:17 - Checking for high voltage locked pixels...
16:07:47 - Checking for high voltage locked pixels...
16:08:17 - Checking for high voltage locked pixels...
16:08:47 - Checking for high voltage locked pixels...