15:01:00 - Successfully configured 2 module(s)
15:01:01 - All front-end boards are programmed with firmware F55D2001
15:01:01 - All backplanes are programmed with firmware 15
15:01:01 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
15:01:01 - Found PPS errors: 3 in drawer 118, 3 in drawer 119
15:01:01 - Finished task "Configure modules"
15:01:04 - Starting task "Switch HVPA voltage state"
15:01:04 - Setting HVPA current limit to 12489.75 uA
15:01:04 - Setting HVPA ramp speed to 25 V/s
15:01:05 - Switching HVPA to state Nominal
15:01:12 - Setting HVPA current limits...
15:01:13 - Finished task "Switch HVPA voltage state"
15:01:38 - Starting task "Check high voltages"
15:01:38 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:01:38 - Actual voltage is between 77.47 V and 868.03 V.
15:01:38 - Low voltages range between 300.00 V and 300.00 V. 
15:01:39 - Reference voltages range between 0.00 V and 1058.82 V. 
15:01:39 - Maximum difference between expected and actual voltages is 181.64 V
15:01:39 - Maximum of current limits is 4379.49 uA
15:01:39 - Checking status of HVPA module in 2 drawer(s)...
15:01:40 - HVPA module in drawer 119 has a status of 0x77!
15:01:40 - Checking status of HVPA channels in 2 drawer(s)...
15:01:40 - HVPA channel 3 of drawer 119 has status 0x8003!
15:01:40 - HV is locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 13 channel(s)
15:01:40 - Resetting 1 channel(s)...
15:01:40 - Resetting HVPA channel 3 of drawer 119...
15:01:48 - Stopping TIB...
15:01:48 - Status: TibState.Running
15:01:48 - Alarms: AlarmVector.BufferFull|AlmostFull
15:01:48 - Connection status: False TXclient_alive: True
15:01:48 - Disabling trigger
15:01:49 - Disabling PPS
15:01:50 - Status: TibState.PpsStopped
15:01:50 - Alarms: AlarmVector.BufferFull|AlmostFull
15:01:50 - Connection status: False TXclient_alive: True
15:01:50 - Closing TIB connection to camera server
15:01:51 - Resetting TIB...
15:01:51 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv5_nd704_dacl.NMC.xml
15:01:51 - Done
15:01:51 - Finished task "Check high voltages"
15:02:12 - Starting task "Check high voltages"
15:02:12 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:02:13 - Actual voltage is between 35.99 V and 1058.35 V.
15:02:13 - Low voltages range between 300.00 V and 300.00 V. 
15:02:13 - Reference voltages range between 952.50 V and 1058.82 V. 
15:02:14 - Maximum difference between expected and actual voltages is 998.87 V
15:02:14 - Maximum of current limits is 4379.49 uA
15:02:14 - Checking status of HVPA module in 2 drawer(s)...
15:02:14 - HVPA module in drawer 119 has a status of 0x77!
15:02:14 - Checking status of HVPA channels in 2 drawer(s)...
15:02:14 - HVPA channel 3 of drawer 119 has status 0x8003!
15:02:14 - HV is locked in 1 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s)
15:02:14 - Resetting 1 channel(s)...
15:02:15 - Resetting HVPA channel 3 of drawer 119...
15:02:17 - High voltage locked channels will be checked every 30 s
15:02:25 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv5_nd704_dacl.NMC.xml
15:02:26 - Done
15:02:26 - Finished task "Check high voltages"
15:02:47 - Checking for high voltage locked pixels...
15:02:57 - Calling method FSM.gotoReady in object FSM
15:03:07 - Calling method FSM.gotoObserving in object FSM
15:03:17 - Checking for high voltage locked pixels...
15:03:32 - Starting task "Check high voltages"
15:03:32 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:03:33 - Actual voltage is between 952.82 V and 1058.96 V.
15:03:33 - Low voltages range between 300.00 V and 300.00 V. 
15:03:33 - Reference voltages range between 952.50 V and 1058.82 V. 
15:03:34 - Maximum difference between expected and actual voltages is 0.48 V
15:03:34 - Maximum of current limits is 4379.49 uA
15:03:34 - Checking status of HVPA module in 2 drawer(s)...
15:03:34 - Checking status of HVPA channels in 2 drawer(s)...
15:03:34 - HV is stabilized in all channels.
15:03:34 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv5_nd704_dacl.NMC.xml
15:03:35 - Done
15:03:35 - Finished task "Check high voltages"
15:03:39 - Starting NMC
15:03:39 - Clearing PPS error counters
15:03:47 - Checking for high voltage locked pixels...
15:03:55 - Configuring calibration box...
15:03:55 - Configuring calibration box with leds=0x0 voltage=10.50 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
15:03:57 - Starting flashes...
15:04:01 - Checking UCTS clock...
15:04:01 - UCTS clock is late by 12 seconds!
15:04:01 - Configuring UCTS
15:04:01 - Configuring TIB...
15:04:01 - Setting TIB forced mode to False
15:04:01 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:04:01 - Status: TibState.RunStopped
15:04:01 - Alarms: AlarmVector.NoAlarm
15:04:01 - Connection status: False TXclient_alive: False
15:04:01 - Disabling PPS
15:04:03 - Status: TibState.PpsStopped
15:04:03 - Alarms: AlarmVector.NoAlarm
15:04:03 - Connection status: False TXclient_alive: False
15:04:03 - Entering set_external_delay
15:04:03 - Setting ExternalDelayLocal to 27.000 ns
15:04:03 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:04:04 - Entering set_external_delay
15:04:04 - Setting ExternalDelayCalibration to 58.000 ns
15:04:04 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:04:04 - Entering set_external_delay
15:04:04 - Setting ExternalDelaySphe to 150.000 ns
15:04:04 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:04:04 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:04:04 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:04:04 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:04:04 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:04:04 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:04:04 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:04:04 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:04:04 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:04:04 - Status: TibState.PpsStopped
15:04:04 - Alarms: AlarmVector.NoAlarm
15:04:04 - Connection status: False TXclient_alive: False
15:04:04 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:04:04 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:04:04 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:04:04 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:04:04 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:04:04 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:04:04 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:04:04 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:04:04 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:04:04 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:04:06 - Connecting TIB to camera server at 10.10.4.12:222
15:04:06 - Starting TIB...
15:04:06 - Status: TibState.PpsStopped
15:04:06 - Alarms: AlarmVector.NoAlarm
15:04:06 - Connection status: False TXclient_alive: True
15:04:06 - Resetting run
15:04:06 - Wait for UCTS external trigger before enabling trigger...
15:04:06 - Status: TibState.Standby
15:04:06 - Alarms: AlarmVector.NoAlarm
15:04:06 - Connection status: False TXclient_alive: True
15:04:06 - Status: TibState.Standby
15:04:06 - Alarms: AlarmVector.NoAlarm
15:04:06 - Connection status: False TXclient_alive: True
15:04:07 - Status: TibState.Armed
15:04:07 - Alarms: AlarmVector.NoAlarm
15:04:07 - Connection status: False TXclient_alive: True
15:04:09 - Starting TIB triggers...
15:04:09 - Enabling trigger
15:04:09 - Status: TibState.Running
15:04:09 - Alarms: AlarmVector.NoAlarm
15:04:09 - Connection status: False TXclient_alive: True
15:04:11 - Status: TibState.Running ConnectionStatus: False TXclient_alive: True
15:04:11 - Alarms: AlarmVector.BufferFull|AlmostFull
15:04:11 - Temperature: 34.25
15:04:11 - Local camera rate: 0.0 Hz
15:04:11 - Stereo trigger rate: 0.0 Hz
15:04:11 - SPE trigger rate: 0.0 Hz
15:04:11 - Calibration trigger rate: 8556.0 Hz
15:04:11 - Software trigger rate: 0.0 Hz
15:04:11 - Pedestal trigger rate: 0.0 Hz
15:04:11 - Collected trigger rate: 7845.0 Hz
15:04:11 - Busy rate: 430.0 Hz
15:04:11 - Camera trigger rate: 7415.0 Hz
15:04:12 - Status: TibState.Running ConnectionStatus: False TXclient_alive: True
15:04:12 - Alarms: AlarmVector.BufferFull|AlmostFull
15:04:12 - Temperature: 34.25
15:04:12 - Local camera rate: 0.0 Hz
15:04:12 - Stereo trigger rate: 0.0 Hz
15:04:12 - SPE trigger rate: 0.0 Hz
15:04:12 - Calibration trigger rate: 8580.0 Hz
15:04:12 - Software trigger rate: 0.0 Hz
15:04:12 - Pedestal trigger rate: 0.0 Hz
15:04:12 - Collected trigger rate: 8527.0 Hz
15:04:12 - Busy rate: 475.0 Hz
15:04:12 - Camera trigger rate: 8052.0 Hz
15:04:17 - Checking for high voltage locked pixels...
15:04:23 - Stopping TIB...
15:04:23 - Status: TibState.Running
15:04:23 - Alarms: AlarmVector.BufferFull|AlmostFull
15:04:23 - Connection status: False TXclient_alive: True
15:04:23 - Disabling trigger
15:04:24 - Disabling PPS
15:04:25 - Status: TibState.PpsStopped
15:04:25 - Alarms: AlarmVector.BufferFull|AlmostFull
15:04:25 - Connection status: False TXclient_alive: True
15:04:25 - Closing TIB connection to camera server
15:04:25 - Status: TibState.PpsStopped
15:04:25 - Alarms: AlarmVector.BufferFull|AlmostFull
15:04:25 - Connection status: False TXclient_alive: False
15:04:25 - Run duration: 0:00:17
15:04:25 - Local camera triggers: 0
15:04:25 - Slow control triggers: 0
15:04:25 - Single photo-electron triggers: 6
15:04:25 - Calibration triggers: 141236
15:04:25 - Software triggers from UCTS: 0
15:04:25 - Pedestal triggers: 0
15:04:25 - Collected input triggers: 121470
15:04:25 - Busy triggers: 7070
15:04:25 - Camera event triggers sent to clusters: 114400
15:04:36 - Calling method FSM.gotoReady in object FSM
15:04:38 - Stopping NMC
15:04:38 - Found 0 PPS errors.