13:44:42 - Checking for high voltage locked pixels...
13:44:54 - Starting task "Configure modules"
13:44:54 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
13:44:54 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
13:44:54 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
13:44:54 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
13:44:54 - Configuring modules with configuration /data/config/2021/20210325/config_tower_2modules_FEBv5_nd704.NMC.xml
13:44:54 - Switching off high voltages in configuration
13:44:58 - Successfully configured 2 module(s)
13:44:58 - All front-end boards are programmed with firmware F55D2001
13:44:58 - All backplanes are programmed with firmware 15
13:44:59 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
13:44:59 - Found 0 PPS errors.
13:44:59 - Finished task "Configure modules"
13:45:01 - Starting task "Switch HVPA voltage state"
13:45:01 - Setting HVPA current limit to 12489.75 uA
13:45:01 - Setting HVPA ramp speed to 25 V/s
13:45:01 - Switching HVPA to state Nominal
13:45:09 - Setting HVPA current limits...
13:45:10 - Finished task "Switch HVPA voltage state"
13:45:12 - Updating voltage widget...
13:45:13 - Checking for high voltage locked pixels...
13:45:17 - Starting task "Check high voltages"
13:45:17 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:45:18 - Actual voltage is between 952.82 V and 1058.35 V.
13:45:18 - Low voltages range between 300.00 V and 300.00 V. 
13:45:18 - Reference voltages range between 952.50 V and 1058.82 V. 
13:45:19 - Maximum difference between expected and actual voltages is 0.50 V
13:45:19 - Maximum of current limits is 4379.49 uA
13:45:19 - Checking status of HVPA module in 2 drawer(s)...
13:45:19 - Checking status of HVPA channels in 2 drawer(s)...
13:45:20 - HV is stabilized in all channels.
13:45:20 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv5_nd704.NMC.xml
13:45:20 - Done
13:45:20 - Finished task "Check high voltages"
13:45:29 - Starting NMC
13:45:29 - Clearing PPS error counters
13:45:34 - Status: TibState.PpsStopped
13:45:34 - Alarms: AlarmVector.BufferFull|AlmostFull
13:45:34 - Connection status: False TXclient_alive: False
13:45:34 - External delays: Local=27.000 ns, Calibration=58.000 ns, Sphe=150.000 ns
13:45:34 - Trigger mask: 0x54 = TriggerMask.SlowControl|Software|Calibration
13:45:34 - Input mask: 0x1
13:45:34 - Disable BUSY: False
13:45:34 - Extra BUSY Delay: 0.0
13:45:34 - Temperature: 34.62
13:45:37 - Resetting TIB...
13:45:40 - Could not invoke the MethodCall service: BadTimeout
13:45:42 - Checking for high voltage locked pixels...
13:45:42 - Calling method FSM.gotoObserving in object FSM
13:46:02 - Configuring calibration box...
13:46:02 - Configuring calibration box with leds=0x358 voltage=10.50 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
13:46:07 - Checking UCTS clock...
13:46:07 - UCTS clock is late by 11 seconds!
13:46:07 - Configuring UCTS
13:46:08 - Configuring TIB...
13:46:08 - Setting TIB forced mode to False
13:46:08 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:46:08 - Status: TibState.RunStopped
13:46:08 - Alarms: AlarmVector.NoAlarm
13:46:08 - Connection status: False TXclient_alive: False
13:46:08 - Disabling PPS
13:46:10 - Status: TibState.PpsStopped
13:46:10 - Alarms: AlarmVector.NoAlarm
13:46:10 - Connection status: False TXclient_alive: False
13:46:10 - Entering set_external_delay
13:46:10 - Setting ExternalDelayLocal to 27.000 ns
13:46:10 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:46:10 - Entering set_external_delay
13:46:10 - Setting ExternalDelayCalibration to 58.000 ns
13:46:10 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:46:10 - Entering set_external_delay
13:46:10 - Setting ExternalDelaySphe to 150.000 ns
13:46:10 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:46:10 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
13:46:10 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:46:10 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:46:10 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:46:10 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:46:10 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:46:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:46:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:46:10 - Status: TibState.PpsStopped
13:46:10 - Alarms: AlarmVector.NoAlarm
13:46:10 - Connection status: False TXclient_alive: False
13:46:10 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:46:10 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:46:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:46:10 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:46:10 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:46:10 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:46:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:46:10 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:46:10 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:46:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:46:12 - Connecting TIB to camera server at 10.10.4.12:222
13:46:12 - Starting TIB...
13:46:12 - Status: TibState.PpsStopped
13:46:12 - Alarms: AlarmVector.NoAlarm
13:46:12 - Connection status: False TXclient_alive: True
13:46:12 - Resetting run
13:46:12 - Wait for UCTS external trigger before enabling trigger...
13:46:12 - Status: TibState.Standby
13:46:12 - Alarms: AlarmVector.NoAlarm
13:46:12 - Connection status: False TXclient_alive: True
13:46:12 - Status: TibState.Standby
13:46:12 - Alarms: AlarmVector.NoAlarm
13:46:12 - Connection status: False TXclient_alive: True
13:46:13 - Status: TibState.Armed
13:46:13 - Alarms: AlarmVector.NoAlarm
13:46:13 - Connection status: True TXclient_alive: True
13:46:13 - Checking for high voltage locked pixels...
13:46:14 - Starting TIB triggers...
13:46:14 - Enabling trigger
13:46:14 - Status: TibState.Running
13:46:14 - Alarms: AlarmVector.NoAlarm
13:46:14 - Connection status: True TXclient_alive: True
13:46:29 - Stopping TIB...
13:46:29 - Status: TibState.Running
13:46:29 - Alarms: AlarmVector.NoAlarm
13:46:29 - Connection status: True TXclient_alive: True
13:46:29 - Disabling trigger
13:46:29 - Disabling PPS
13:46:30 - Status: TibState.PpsStopped
13:46:30 - Alarms: AlarmVector.NoAlarm
13:46:30 - Connection status: True TXclient_alive: True
13:46:30 - Closing TIB connection to camera server
13:46:31 - Status: TibState.PpsStopped
13:46:31 - Alarms: AlarmVector.NoAlarm
13:46:31 - Connection status: False TXclient_alive: False
13:46:31 - Run duration: 0:00:16
13:46:31 - Local camera triggers: 0
13:46:31 - Slow control triggers: 0
13:46:31 - Single photo-electron triggers: 0
13:46:31 - Calibration triggers: 133593
13:46:31 - Software triggers from UCTS: 0
13:46:31 - Pedestal triggers: 0
13:46:31 - Collected input triggers: 121947
13:46:31 - Busy triggers: 7000
13:46:31 - Camera event triggers sent to clusters: 114947
13:46:33 - Calling method FSM.gotoReady in object FSM
13:46:36 - Stopping NMC
13:46:36 - Found 0 PPS errors.