11:35:00 - Starting task "Configure modules"
11:35:00 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
11:35:00 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
11:35:00 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
11:35:00 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
11:35:00 - Configuring modules with configuration /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy0_nd681.NMC.xml
11:35:00 - Switching off high voltages in configuration
11:35:03 - Successfully configured 2 module(s)
11:35:04 - All front-end boards are programmed with firmware 61210216
11:35:04 - All backplanes are programmed with firmware 15
11:35:04 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
11:35:05 - Found 0 PPS errors.
11:35:05 - Finished task "Configure modules"
11:35:09 - Starting task "Switch HVPA voltage state"
11:35:09 - Setting HVPA current limit to 12489.75 uA
11:35:10 - Setting HVPA ramp speed to 25 V/s
11:35:10 - Switching HVPA to state Nominal
11:35:14 - Stopping flashes...
11:35:17 - Setting HVPA current limits...
11:35:18 - Finished task "Switch HVPA voltage state"
11:35:30 - Starting task "Check high voltages"
11:35:30 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:35:30 - Actual voltage is between 557.54 V and 583.16 V.
11:35:31 - Low voltages range between 300.00 V and 300.00 V. 
11:35:31 - Reference voltages range between 984.98 V and 1117.51 V. 
11:35:31 - Maximum difference between expected and actual voltages is 508.12 V
11:35:32 - Maximum of current limits is 4840.96 uA
11:35:32 - Checking status of HVPA module in 2 drawer(s)...
11:35:32 - Checking status of HVPA channels in 2 drawer(s)...
11:35:32 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 14 channel(s)
11:35:32 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy0_nd681.NMC.xml
11:35:32 - Done
11:35:33 - Finished task "Check high voltages"
11:35:48 - Starting task "Check high voltages"
11:35:48 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:35:49 - Actual voltage is between 984.54 V and 1090.68 V.
11:35:49 - Low voltages range between 300.00 V and 300.00 V. 
11:35:49 - Reference voltages range between 984.98 V and 1117.51 V. 
11:35:50 - Maximum difference between expected and actual voltages is 8.53 V
11:35:50 - Maximum of current limits is 4840.96 uA
11:35:50 - Checking status of HVPA module in 2 drawer(s)...
11:35:50 - Checking status of HVPA channels in 2 drawer(s)...
11:35:50 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 2 channel(s)
11:35:50 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy0_nd681.NMC.xml
11:35:51 - Done
11:35:51 - Finished task "Check high voltages"
11:36:05 - Starting task "Check high voltages"
11:36:05 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:36:06 - Actual voltage is between 985.15 V and 1117.52 V.
11:36:06 - Low voltages range between 300.00 V and 300.00 V. 
11:36:06 - Reference voltages range between 984.98 V and 1117.51 V. 
11:36:07 - Maximum difference between expected and actual voltages is 0.45 V
11:36:07 - Maximum of current limits is 4840.96 uA
11:36:07 - Checking status of HVPA module in 2 drawer(s)...
11:36:07 - Checking status of HVPA channels in 2 drawer(s)...
11:36:07 - HV is stabilized in all channels.
11:36:07 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy0_nd681.NMC.xml
11:36:08 - Done
11:36:08 - Finished task "Check high voltages"
11:36:14 - Starting task "Set L0 trigger thresholds"
11:36:14 - Setting L0 thresholds to 3.0 p.e. using /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:36:15 - Setting L0 thresholds to 3.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:36:15 - Thresholds saved in configuration file /data/config/2021/20210325/config_2021-03-25_11-36-15.NMC.xml
11:36:15 - Finished task "Set L0 trigger thresholds"
11:36:30 - Updating L0 scaler widget...
11:36:33 - Updating L1 scaler widget...
11:36:42 - Starting task "Set L0 trigger thresholds"
11:36:42 - Setting L0 thresholds to 5.0 p.e. using /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:36:43 - Setting L0 thresholds to 5.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:36:43 - Thresholds saved in configuration file /data/config/2021/20210325/config_2021-03-25_11-36-43.NMC.xml
11:36:43 - Finished task "Set L0 trigger thresholds"
11:36:47 - Updating L0 scaler widget...
11:36:50 - Updating L1 scaler widget...
11:36:53 - Updating L1 scaler widget...
11:37:01 - Starting task "Set L0 trigger thresholds"
11:37:01 - Setting L0 thresholds to 10.0 p.e. using /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:37:02 - Setting L0 thresholds to 10.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:37:02 - Thresholds saved in configuration file /data/config/2021/20210325/config_2021-03-25_11-37-02.NMC.xml
11:37:02 - Finished task "Set L0 trigger thresholds"
11:37:04 - Updating L0 scaler widget...
11:37:06 - Updating L0 scaler widget...
11:37:08 - Updating L1 scaler widget...
11:37:12 - Updating L1 scaler widget...
11:37:13 - Updating L1 scaler widget...
11:37:14 - Updating L1 scaler widget...
11:37:18 - Updating L0 scaler widget...
11:37:20 - Updating L0 scaler widget...
11:37:24 - Updating L0 scaler widget...
11:37:44 - Updating L0 scaler widget...
11:37:47 - Updating L1 scaler widget...
11:37:55 - Starting task "Set L0 trigger thresholds"
11:37:55 - Setting L0 thresholds to 8.0 p.e. using /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:37:56 - Setting L0 thresholds to 8.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:37:56 - Thresholds saved in configuration file /data/config/2021/20210325/config_2021-03-25_11-37-56.NMC.xml
11:37:56 - Finished task "Set L0 trigger thresholds"
11:37:57 - Updating L0 scaler widget...
11:38:00 - Updating L1 scaler widget...
11:38:01 - Updating L1 scaler widget...
11:38:03 - Updating L1 scaler widget...
11:38:04 - Updating L1 scaler widget...
11:38:05 - Updating L1 scaler widget...
11:38:06 - Updating L1 scaler widget...
11:38:08 - Updating L1 scaler widget...
11:38:21 - Starting task "Set L0 trigger thresholds"
11:38:21 - Setting L0 thresholds to 6.0 p.e. using /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:38:22 - Setting L0 thresholds to 6.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
11:38:22 - Thresholds saved in configuration file /data/config/2021/20210325/config_2021-03-25_11-38-22.NMC.xml
11:38:22 - Finished task "Set L0 trigger thresholds"
11:38:23 - Updating L1 scaler widget...
11:38:25 - Updating L1 scaler widget...
11:38:26 - Updating L1 scaler widget...
11:38:49 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:38:49 - Alarms: AlarmVector.NoAlarm
11:38:49 - Temperature: 35.12
11:38:49 - Local camera rate: 1.0 Hz
11:38:49 - Stereo trigger rate: 0.0 Hz
11:38:49 - SPE trigger rate: 0.0 Hz
11:38:49 - Calibration trigger rate: 8382.0 Hz
11:38:49 - Software trigger rate: 0.0 Hz
11:38:49 - Pedestal trigger rate: 0.0 Hz
11:38:49 - Collected trigger rate: 0.0 Hz
11:38:49 - Busy rate: 0.0 Hz
11:38:49 - Camera trigger rate: 0.0 Hz
11:38:51 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:38:51 - Alarms: AlarmVector.NoAlarm
11:38:51 - Temperature: 35.06
11:38:51 - Local camera rate: 1.0 Hz
11:38:51 - Stereo trigger rate: 0.0 Hz
11:38:51 - SPE trigger rate: 0.0 Hz
11:38:51 - Calibration trigger rate: 8382.0 Hz
11:38:51 - Software trigger rate: 0.0 Hz
11:38:51 - Pedestal trigger rate: 0.0 Hz
11:38:51 - Collected trigger rate: 0.0 Hz
11:38:51 - Busy rate: 0.0 Hz
11:38:51 - Camera trigger rate: 0.0 Hz
11:38:56 - Stopping flashes...
11:38:59 - Configuring calibration box...
11:38:59 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
11:39:03 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:39:03 - Alarms: AlarmVector.NoAlarm
11:39:03 - Temperature: 35.12
11:39:03 - Local camera rate: 1.0 Hz
11:39:03 - Stereo trigger rate: 0.0 Hz
11:39:03 - SPE trigger rate: 0.0 Hz
11:39:03 - Calibration trigger rate: 0.0 Hz
11:39:03 - Software trigger rate: 0.0 Hz
11:39:03 - Pedestal trigger rate: 0.0 Hz
11:39:03 - Collected trigger rate: 0.0 Hz
11:39:03 - Busy rate: 0.0 Hz
11:39:03 - Camera trigger rate: 0.0 Hz
11:39:04 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:39:04 - Alarms: AlarmVector.NoAlarm
11:39:04 - Temperature: 35.12
11:39:04 - Local camera rate: 1.0 Hz
11:39:04 - Stereo trigger rate: 0.0 Hz
11:39:04 - SPE trigger rate: 0.0 Hz
11:39:04 - Calibration trigger rate: 0.0 Hz
11:39:04 - Software trigger rate: 0.0 Hz
11:39:04 - Pedestal trigger rate: 0.0 Hz
11:39:04 - Collected trigger rate: 0.0 Hz
11:39:04 - Busy rate: 0.0 Hz
11:39:04 - Camera trigger rate: 0.0 Hz
11:39:07 - Updating L1 scaler widget...
11:39:33 - Configuring calibration box...
11:39:33 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=False fiber1_out=False fiber2_out=False lemo_in=True enabled=True
11:39:36 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:39:36 - Alarms: AlarmVector.NoAlarm
11:39:36 - Temperature: 35.12
11:39:36 - Local camera rate: 1.0 Hz
11:39:36 - Stereo trigger rate: 0.0 Hz
11:39:36 - SPE trigger rate: 0.0 Hz
11:39:36 - Calibration trigger rate: 0.0 Hz
11:39:36 - Software trigger rate: 0.0 Hz
11:39:36 - Pedestal trigger rate: 0.0 Hz
11:39:36 - Collected trigger rate: 0.0 Hz
11:39:36 - Busy rate: 0.0 Hz
11:39:36 - Camera trigger rate: 0.0 Hz
11:39:37 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:39:37 - Alarms: AlarmVector.NoAlarm
11:39:37 - Temperature: 35.12
11:39:37 - Local camera rate: 1.0 Hz
11:39:37 - Stereo trigger rate: 0.0 Hz
11:39:37 - SPE trigger rate: 0.0 Hz
11:39:37 - Calibration trigger rate: 0.0 Hz
11:39:37 - Software trigger rate: 0.0 Hz
11:39:37 - Pedestal trigger rate: 0.0 Hz
11:39:37 - Collected trigger rate: 0.0 Hz
11:39:37 - Busy rate: 0.0 Hz
11:39:37 - Camera trigger rate: 0.0 Hz
11:39:51 - Configuring calibration box...
11:39:51 - Configuring calibration box with leds=0x358 voltage=10.50 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=False fiber1_out=False fiber2_out=False lemo_in=True enabled=True
11:39:53 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:39:53 - Alarms: AlarmVector.NoAlarm
11:39:53 - Temperature: 35.06
11:39:53 - Local camera rate: 1.0 Hz
11:39:53 - Stereo trigger rate: 0.0 Hz
11:39:53 - SPE trigger rate: 0.0 Hz
11:39:53 - Calibration trigger rate: 0.0 Hz
11:39:53 - Software trigger rate: 0.0 Hz
11:39:53 - Pedestal trigger rate: 0.0 Hz
11:39:53 - Collected trigger rate: 0.0 Hz
11:39:53 - Busy rate: 0.0 Hz
11:39:53 - Camera trigger rate: 0.0 Hz
11:39:54 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:39:54 - Alarms: AlarmVector.NoAlarm
11:39:54 - Temperature: 35.06
11:39:54 - Local camera rate: 1.0 Hz
11:39:54 - Stereo trigger rate: 0.0 Hz
11:39:54 - SPE trigger rate: 0.0 Hz
11:39:54 - Calibration trigger rate: 0.0 Hz
11:39:54 - Software trigger rate: 0.0 Hz
11:39:54 - Pedestal trigger rate: 0.0 Hz
11:39:54 - Collected trigger rate: 0.0 Hz
11:39:54 - Busy rate: 0.0 Hz
11:39:54 - Camera trigger rate: 0.0 Hz
11:40:01 - Checking status of calibration box...
11:40:02 - Calibration box is configured with 5 leds at a frequency of 10.0 Hz and a voltage of 10.49 V
11:40:09 - Starting task "Check high voltages"
11:40:09 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:40:10 - Actual voltage is between 984.54 V and 1117.52 V.
11:40:10 - Low voltages range between 300.00 V and 300.00 V. 
11:40:10 - Reference voltages range between 984.98 V and 1117.51 V. 
11:40:11 - Maximum difference between expected and actual voltages is 0.39 V
11:40:11 - Maximum of current limits is 4840.96 uA
11:40:11 - Checking status of HVPA module in 2 drawer(s)...
11:40:11 - Checking status of HVPA channels in 2 drawer(s)...
11:40:11 - HV is stabilized in all channels.
11:40:11 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy0_nd681.NMC.xml
11:40:12 - Done
11:40:12 - Finished task "Check high voltages"
11:40:12 - High voltage locked channels will be checked every 30 s
11:40:16 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:40:16 - Alarms: AlarmVector.NoAlarm
11:40:16 - Temperature: 35.12
11:40:16 - Local camera rate: 1.0 Hz
11:40:16 - Stereo trigger rate: 0.0 Hz
11:40:16 - SPE trigger rate: 0.0 Hz
11:40:16 - Calibration trigger rate: 2.0 Hz
11:40:16 - Software trigger rate: 0.0 Hz
11:40:16 - Pedestal trigger rate: 0.0 Hz
11:40:16 - Collected trigger rate: 0.0 Hz
11:40:16 - Busy rate: 0.0 Hz
11:40:16 - Camera trigger rate: 0.0 Hz
11:40:18 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:40:18 - Alarms: AlarmVector.NoAlarm
11:40:18 - Temperature: 35.06
11:40:18 - Local camera rate: 1.0 Hz
11:40:18 - Stereo trigger rate: 0.0 Hz
11:40:18 - SPE trigger rate: 0.0 Hz
11:40:18 - Calibration trigger rate: 0.0 Hz
11:40:18 - Software trigger rate: 0.0 Hz
11:40:18 - Pedestal trigger rate: 0.0 Hz
11:40:18 - Collected trigger rate: 0.0 Hz
11:40:18 - Busy rate: 0.0 Hz
11:40:18 - Camera trigger rate: 0.0 Hz
11:40:20 - Updating L1 scaler widget...
11:40:23 - Updating L1 scaler widget...
11:40:24 - Updating L1 scaler widget...
11:40:25 - Updating L1 scaler widget...
11:40:26 - Updating L1 scaler widget...
11:40:35 - Calling method FSM.gotoObserving in object FSM
11:40:42 - Checking for high voltage locked pixels...
11:40:45 - Starting NMC
11:40:45 - Clearing PPS error counters
11:40:48 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
11:40:48 - Alarms: AlarmVector.NoAlarm
11:40:48 - Temperature: 35.12
11:40:48 - Local camera rate: 1.0 Hz
11:40:48 - Stereo trigger rate: 0.0 Hz
11:40:48 - SPE trigger rate: 0.0 Hz
11:40:48 - Calibration trigger rate: 0.0 Hz
11:40:48 - Software trigger rate: 0.0 Hz
11:40:49 - Pedestal trigger rate: 0.0 Hz
11:40:49 - Collected trigger rate: 0.0 Hz
11:40:49 - Busy rate: 0.0 Hz
11:40:49 - Camera trigger rate: 0.0 Hz
11:41:03 - Checking UCTS clock...
11:41:04 - UCTS clock is late by 12 seconds!
11:41:04 - Configuring UCTS
11:41:04 - Configuring TIB...
11:41:04 - Setting TIB forced mode to False
11:41:04 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:41:04 - Status: TibState.PpsStopped
11:41:04 - Alarms: AlarmVector.NoAlarm
11:41:04 - Connection status: False TXclient_alive: False
11:41:04 - Entering set_external_delay
11:41:04 - Setting ExternalDelayLocal to 27.000 ns
11:41:04 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:41:04 - Entering set_external_delay
11:41:04 - Setting ExternalDelayCalibration to 58.000 ns
11:41:04 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:41:04 - Entering set_external_delay
11:41:04 - Setting ExternalDelaySphe to 150.000 ns
11:41:04 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:41:04 - Setting TIB trigger mode to 0x51 = TriggerMask.SlowControl|Software|Mono
11:41:04 - Writing 81 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:41:05 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:41:06 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:41:06 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:41:06 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:41:06 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:41:06 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:41:06 - Status: TibState.PpsStopped
11:41:06 - Alarms: AlarmVector.NoAlarm
11:41:06 - Connection status: False TXclient_alive: False
11:41:06 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:41:06 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:41:06 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:41:06 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:41:06 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:41:06 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:41:06 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:41:06 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:41:06 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:41:06 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:41:07 - Connecting TIB to camera server at 10.10.4.12:222
11:41:07 - Starting TIB...
11:41:07 - Status: TibState.PpsStopped
11:41:07 - Alarms: AlarmVector.NoAlarm
11:41:08 - Connection status: False TXclient_alive: True
11:41:08 - Resetting run
11:41:08 - Wait for UCTS external trigger before enabling trigger...
11:41:08 - Status: TibState.Standby
11:41:08 - Alarms: AlarmVector.NoAlarm
11:41:08 - Connection status: False TXclient_alive: True
11:41:08 - Status: TibState.Standby
11:41:08 - Alarms: AlarmVector.NoAlarm
11:41:08 - Connection status: False TXclient_alive: True
11:41:09 - Status: TibState.Armed
11:41:09 - Alarms: AlarmVector.NoAlarm
11:41:09 - Connection status: True TXclient_alive: True
11:41:11 - Starting TIB triggers...
11:41:11 - Enabling trigger
11:41:11 - Status: TibState.Running
11:41:11 - Alarms: AlarmVector.NoAlarm
11:41:11 - Connection status: True TXclient_alive: True
11:41:12 - Checking for high voltage locked pixels...
11:41:13 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
11:41:13 - Alarms: AlarmVector.NoAlarm
11:41:13 - Temperature: 35.12
11:41:13 - Local camera rate: 1.0 Hz
11:41:13 - Stereo trigger rate: 0.0 Hz
11:41:13 - SPE trigger rate: 0.0 Hz
11:41:13 - Calibration trigger rate: 0.0 Hz
11:41:13 - Software trigger rate: 0.0 Hz
11:41:13 - Pedestal trigger rate: 0.0 Hz
11:41:13 - Collected trigger rate: 62734.0 Hz
11:41:13 - Busy rate: 46496.0 Hz
11:41:13 - Camera trigger rate: 16238.0 Hz
11:41:21 - Stopping TIB...
11:41:21 - Status: TibState.Running
11:41:21 - Alarms: AlarmVector.NoAlarm
11:41:21 - Connection status: True TXclient_alive: True
11:41:21 - Disabling trigger
11:41:21 - Disabling PPS
11:41:22 - Status: TibState.PpsStopped
11:41:22 - Alarms: AlarmVector.NoAlarm
11:41:22 - Connection status: True TXclient_alive: True
11:41:22 - Closing TIB connection to camera server
11:41:26 - Status: TibState.PpsStopped
11:41:26 - Alarms: AlarmVector.NoAlarm
11:41:26 - Connection status: False TXclient_alive: False
11:41:26 - Run duration: 0:00:12
11:41:26 - Local camera triggers: 1
11:41:26 - Slow control triggers: 0
11:41:26 - Single photo-electron triggers: 0
11:41:26 - Calibration triggers: 0
11:41:26 - Software triggers from UCTS: 0
11:41:26 - Pedestal triggers: 0
11:41:26 - Collected input triggers: 622418
11:41:26 - Busy triggers: 462347
11:41:26 - Camera event triggers sent to clusters: 160071
11:41:42 - Checking for high voltage locked pixels...
11:41:49 - Calling method FSM.gotoReady in object FSM
11:41:52 - Stopping NMC
11:41:52 - Found 0 PPS errors.
11:42:12 - Checking for high voltage locked pixels...