11:06:18 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
11:06:18 - Found 0 PPS errors.
11:06:21 - Starting task "Configure modules"
11:06:21 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
11:06:21 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
11:06:21 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
11:06:21 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
11:06:21 - Configuring modules with configuration /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy14_nd681.NMC.xml
11:06:21 - Switching off high voltages in configuration
11:06:24 - Checking for high voltage locked pixels...
11:06:24 - Successfully configured 2 module(s)
11:06:25 - All front-end boards are programmed with firmware 61210216
11:06:25 - All backplanes are programmed with firmware 15
11:06:26 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
11:06:26 - Found 0 PPS errors.
11:06:26 - Finished task "Configure modules"
11:06:27 - Starting task "Switch HVPA voltage state"
11:06:27 - Setting HVPA current limit to 12489.75 uA
11:06:27 - Setting HVPA ramp speed to 25 V/s
11:06:27 - Switching HVPA to state Nominal
11:06:35 - Setting HVPA current limits...
11:06:36 - Finished task "Switch HVPA voltage state"
11:06:44 - Starting task "Check high voltages"
11:06:44 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:06:45 - Actual voltage is between 982.71 V and 1114.47 V.
11:06:45 - Low voltages range between 300.00 V and 300.00 V. 
11:06:45 - Reference voltages range between 984.98 V and 1117.51 V. 
11:06:46 - Maximum difference between expected and actual voltages is 1.21 V
11:06:46 - Maximum of current limits is 4840.96 uA
11:06:46 - Checking status of HVPA module in 2 drawer(s)...
11:06:46 - Checking status of HVPA channels in 2 drawer(s)...
11:06:46 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
11:06:46 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy14_nd681.NMC.xml
11:06:47 - Done
11:06:47 - Finished task "Check high voltages"
11:06:50 - Starting NMC
11:06:50 - Clearing PPS error counters
11:06:53 - Calling method FSM.gotoObserving in object FSM
11:06:56 - Checking for high voltage locked pixels...
11:07:13 - Calling method FSM.gotoReady in object FSM
11:07:17 - Calling method FSM.gotoObserving in object FSM
11:07:24 - Checking for high voltage locked pixels...
11:07:27 - Configuring calibration box...
11:07:27 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
11:07:29 - Checking UCTS clock...
11:07:30 - UCTS clock is late by 12 seconds!
11:07:30 - Configuring UCTS
11:07:30 - Configuring TIB...
11:07:30 - Setting TIB forced mode to False
11:07:30 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:07:30 - Status: TibState.PpsStopped
11:07:30 - Alarms: AlarmVector.NoAlarm
11:07:30 - Connection status: False TXclient_alive: False
11:07:30 - Entering set_external_delay
11:07:30 - Setting ExternalDelayLocal to 27.000 ns
11:07:30 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:07:30 - Entering set_external_delay
11:07:30 - Setting ExternalDelayCalibration to 58.000 ns
11:07:30 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:07:30 - Entering set_external_delay
11:07:30 - Setting ExternalDelaySphe to 150.000 ns
11:07:30 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:07:30 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
11:07:30 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:07:30 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:07:30 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:07:30 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:07:30 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:07:30 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:07:30 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:07:30 - Status: TibState.PpsStopped
11:07:30 - Alarms: AlarmVector.NoAlarm
11:07:30 - Connection status: False TXclient_alive: False
11:07:30 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:07:31 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:07:31 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:07:31 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:07:31 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:07:31 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:07:31 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:07:31 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:07:31 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:07:31 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:07:32 - Connecting TIB to camera server at 10.10.4.12:222
11:07:32 - Starting TIB...
11:07:32 - Status: TibState.PpsStopped
11:07:32 - Alarms: AlarmVector.NoAlarm
11:07:32 - Connection status: False TXclient_alive: True
11:07:32 - Resetting run
11:07:32 - Wait for UCTS external trigger before enabling trigger...
11:07:32 - Status: TibState.Standby
11:07:32 - Alarms: AlarmVector.NoAlarm
11:07:32 - Connection status: False TXclient_alive: True
11:07:32 - Status: TibState.Standby
11:07:32 - Alarms: AlarmVector.NoAlarm
11:07:32 - Connection status: False TXclient_alive: True
11:07:33 - Status: TibState.CoutingPps
11:07:33 - Alarms: AlarmVector.NoAlarm
11:07:33 - Connection status: False TXclient_alive: True
11:07:35 - Starting TIB triggers...
11:07:35 - Enabling trigger
11:07:35 - Status: TibState.Running
11:07:35 - Alarms: AlarmVector.NoAlarm
11:07:35 - Connection status: True TXclient_alive: True
11:07:36 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
11:07:36 - Alarms: AlarmVector.NoAlarm
11:07:36 - Temperature: 35.25
11:07:36 - Local camera rate: 0.0 Hz
11:07:36 - Stereo trigger rate: 0.0 Hz
11:07:36 - SPE trigger rate: 0.0 Hz
11:07:36 - Calibration trigger rate: 8428.0 Hz
11:07:36 - Software trigger rate: 0.0 Hz
11:07:36 - Pedestal trigger rate: 0.0 Hz
11:07:36 - Collected trigger rate: 0.0 Hz
11:07:36 - Busy rate: 0.0 Hz
11:07:36 - Camera trigger rate: 0.0 Hz
11:07:54 - Checking for high voltage locked pixels...
11:08:00 - Stopping TIB...
11:08:00 - Status: TibState.Running
11:08:00 - Alarms: AlarmVector.NoAlarm
11:08:00 - Connection status: True TXclient_alive: True
11:08:00 - Disabling trigger
11:08:00 - Disabling PPS
11:08:01 - Status: TibState.PpsStopped
11:08:01 - Alarms: AlarmVector.NoAlarm
11:08:01 - Connection status: True TXclient_alive: True
11:08:01 - Closing TIB connection to camera server
11:08:01 - Status: TibState.PpsStopped
11:08:02 - Alarms: AlarmVector.NoAlarm
11:08:02 - Connection status: False TXclient_alive: False
11:08:02 - Run duration: 0:00:27
11:08:02 - Local camera triggers: 0
11:08:02 - Slow control triggers: 0
11:08:02 - Single photo-electron triggers: 0
11:08:02 - Calibration triggers: 225002
11:08:02 - Software triggers from UCTS: 0
11:08:02 - Pedestal triggers: 0
11:08:02 - Collected input triggers: 208135
11:08:02 - Busy triggers: 2138
11:08:02 - Camera event triggers sent to clusters: 205997
11:08:05 - Calling method FSM.gotoReady in object FSM
11:08:07 - Stopping NMC
11:08:07 - Found 0 PPS errors.
11:08:24 - Checking for high voltage locked pixels...