10:55:36 - Starting task "Configure modules"
10:55:36 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
10:55:36 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
10:55:36 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
10:55:36 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
10:55:36 - Configuring modules with configuration /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy8_nd681.NMC.xml
10:55:36 - Switching off high voltages in configuration
10:55:39 - Successfully configured 2 module(s)
10:55:40 - All front-end boards are programmed with firmware 61210216
10:55:40 - All backplanes are programmed with firmware 15
10:55:41 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
10:55:41 - Found 0 PPS errors.
10:55:41 - Finished task "Configure modules"
10:55:42 - Starting task "Switch HVPA voltage state"
10:55:42 - Setting HVPA current limit to 12489.75 uA
10:55:42 - Setting HVPA ramp speed to 25 V/s
10:55:43 - Switching HVPA to state Nominal
10:55:44 - Starting NMC
10:55:44 - Clearing PPS error counters
10:55:47 - Calling method FSM.gotoObserving in object FSM
10:55:50 - Setting HVPA current limits...
10:55:51 - Finished task "Switch HVPA voltage state"
10:55:54 - Checking for high voltage locked pixels...
10:56:02 - Configuring calibration box...
10:56:02 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=300.0/30 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
10:56:04 - Starting task "Check high voltages"
10:56:04 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:56:05 - Actual voltage is between 984.54 V and 1117.52 V.
10:56:05 - Low voltages range between 300.00 V and 300.00 V. 
10:56:05 - Reference voltages range between 984.98 V and 1117.51 V. 
10:56:06 - Maximum difference between expected and actual voltages is 0.45 V
10:56:06 - Maximum of current limits is 4840.96 uA
10:56:06 - Checking status of HVPA module in 2 drawer(s)...
10:56:06 - Checking status of HVPA channels in 2 drawer(s)...
10:56:06 - HV is stabilized in all channels.
10:56:06 - Checking reference and low voltages against /data/config/2021/20210325/config_tower_2modules_FEBv6_pingpong_DelayBusy8_nd681.NMC.xml
10:56:07 - Done
10:56:07 - Finished task "Check high voltages"
10:56:08 - Checking UCTS clock...
10:56:09 - UCTS clock is late by 12 seconds!
10:56:09 - Configuring UCTS
10:56:09 - Configuring TIB...
10:56:09 - Setting TIB forced mode to False
10:56:09 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:56:09 - Status: TibState.PpsStopped
10:56:09 - Alarms: AlarmVector.NoAlarm
10:56:09 - Connection status: False TXclient_alive: False
10:56:09 - Entering set_external_delay
10:56:09 - Setting ExternalDelayLocal to 27.000 ns
10:56:09 - Writing 27.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:56:09 - Entering set_external_delay
10:56:09 - Setting ExternalDelayCalibration to 58.000 ns
10:56:09 - Writing 58.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:56:09 - Entering set_external_delay
10:56:09 - Setting ExternalDelaySphe to 150.000 ns
10:56:09 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:56:09 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:56:09 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:56:09 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:56:09 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:56:09 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:56:09 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:56:09 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:56:09 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:56:09 - Status: TibState.PpsStopped
10:56:09 - Alarms: AlarmVector.NoAlarm
10:56:09 - Connection status: False TXclient_alive: False
10:56:09 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:56:09 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:56:09 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:56:09 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:56:09 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:56:09 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:56:09 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:56:09 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:56:09 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:56:09 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:56:11 - Connecting TIB to camera server at 10.10.4.12:222
10:56:11 - Starting TIB...
10:56:11 - Status: TibState.PpsStopped
10:56:11 - Alarms: AlarmVector.NoAlarm
10:56:11 - Connection status: False TXclient_alive: True
10:56:11 - Resetting run
10:56:11 - Wait for UCTS external trigger before enabling trigger...
10:56:11 - Status: TibState.Standby
10:56:11 - Alarms: AlarmVector.NoAlarm
10:56:11 - Connection status: False TXclient_alive: True
10:56:11 - Status: TibState.Standby
10:56:11 - Alarms: AlarmVector.NoAlarm
10:56:11 - Connection status: False TXclient_alive: True
10:56:12 - Status: TibState.Armed
10:56:12 - Alarms: AlarmVector.NoAlarm
10:56:12 - Connection status: True TXclient_alive: True
10:56:14 - Starting TIB triggers...
10:56:14 - Enabling trigger
10:56:14 - Status: TibState.Running
10:56:14 - Alarms: AlarmVector.NoAlarm
10:56:14 - Connection status: True TXclient_alive: True
10:56:15 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
10:56:15 - Alarms: AlarmVector.NoAlarm
10:56:15 - Temperature: 35.25
10:56:15 - Local camera rate: 0.0 Hz
10:56:15 - Stereo trigger rate: 0.0 Hz
10:56:15 - SPE trigger rate: 0.0 Hz
10:56:15 - Calibration trigger rate: 8321.0 Hz
10:56:15 - Software trigger rate: 0.0 Hz
10:56:15 - Pedestal trigger rate: 0.0 Hz
10:56:15 - Collected trigger rate: 1515.0 Hz
10:56:15 - Busy rate: 9.0 Hz
10:56:15 - Camera trigger rate: 1506.0 Hz
10:56:24 - Checking for high voltage locked pixels...
10:56:46 - Stopping TIB...
10:56:46 - Status: TibState.Running
10:56:46 - Alarms: AlarmVector.NoAlarm
10:56:46 - Connection status: True TXclient_alive: True
10:56:46 - Disabling trigger
10:56:46 - Disabling PPS
10:56:47 - Status: TibState.PpsStopped
10:56:47 - Alarms: AlarmVector.NoAlarm
10:56:47 - Connection status: True TXclient_alive: True
10:56:47 - Closing TIB connection to camera server
10:56:48 - Status: TibState.PpsStopped
10:56:48 - Alarms: AlarmVector.NoAlarm
10:56:48 - Connection status: False TXclient_alive: False
10:56:48 - Run duration: 0:00:34
10:56:48 - Local camera triggers: 0
10:56:48 - Slow control triggers: 0
10:56:48 - Single photo-electron triggers: 0
10:56:48 - Calibration triggers: 277925
10:56:48 - Software triggers from UCTS: 0
10:56:48 - Pedestal triggers: 0
10:56:48 - Collected input triggers: 268470
10:56:48 - Busy triggers: 1890
10:56:48 - Camera event triggers sent to clusters: 266580
10:56:52 - Calling method FSM.gotoReady in object FSM
10:56:54 - Checking for high voltage locked pixels...
10:56:54 - Stopping NMC
10:56:54 - Found 0 PPS errors.