10:27:48 - Checking for high voltage locked pixels...
10:27:49 - Stopping NMC
10:27:49 - Found 0 PPS errors.
10:27:50 - Starting NMC
10:27:50 - Clearing PPS error counters
10:27:51 - Starting task "Check high voltages"
10:27:51 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:27:52 - Actual voltage is between 984.54 V and 1116.91 V.
10:27:52 - Low voltages range between 300.00 V and 300.00 V. 
10:27:52 - Reference voltages range between 984.98 V and 1117.51 V. 
10:27:53 - Maximum difference between expected and actual voltages is 0.45 V
10:27:53 - Maximum of current limits is 4840.96 uA
10:27:53 - Checking status of HVPA module in 2 drawer(s)...
10:27:53 - Checking status of HVPA channels in 2 drawer(s)...
10:27:53 - HV is stabilized in all channels.
10:27:53 - Checking reference and low voltages against /data/config/2021/20210315/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newDACL_newHV2.NMC.xml
10:27:54 - Done
10:27:54 - Finished task "Check high voltages"
10:28:18 - Checking for high voltage locked pixels...
10:28:37 - Starting task "Set L0 trigger thresholds"
10:28:37 - Setting L0 thresholds to 20.0 p.e. using /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
10:28:38 - Setting L0 thresholds to 20.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20200708.h5
10:28:38 - Thresholds saved in configuration file /data/config/2021/20210316/config_2021-03-16_10-28-38.NMC.xml
10:28:38 - Finished task "Set L0 trigger thresholds"
10:28:44 - Starting task "Set DTC trigger masks"
10:28:44 - Configuring DTC trigger masks for 2 configured module(s)
10:28:44 - Setting DTC slot 1 trigger mask to 0x0000
10:28:44 - Setting DTC slot 5 trigger mask to 0x0000
10:28:44 - Setting DTC slot 6 trigger mask to 0x0000
10:28:44 - Setting DTC slot 9 trigger mask to 0x0000
10:28:44 - Setting DTC slot 13 trigger mask to 0x0000
10:28:44 - Setting DTC slot 14 trigger mask to 0x0000
10:28:44 - Setting DTC slot 15 trigger mask to 0x0000
10:28:45 - Setting DTC slot 19 trigger mask to 0x9000
10:28:45 - Finished task "Set DTC trigger masks"
10:28:48 - Checking for high voltage locked pixels...
10:29:18 - Checking for high voltage locked pixels...
10:29:48 - Checking for high voltage locked pixels...
10:29:52 - Configuring calibration box...
10:29:52 - Configuring calibration box with leds=0x358 voltage=10.50 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
10:29:56 - Updating L0 scaler widget...
10:29:58 - Updating L0 scaler widget...
10:30:01 - Updating L1 scaler widget...
10:30:11 - Calling method FSM.gotoObserving in object FSM
10:30:18 - Checking for high voltage locked pixels...
10:30:34 - Checking UCTS clock...
10:30:34 - UCTS clock is late by 5 seconds!
10:30:34 - Configuring UCTS
10:30:34 - Configuring TIB...
10:30:34 - Setting TIB forced mode to False
10:30:34 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:30:34 - Status: TibState.PpsStopped
10:30:34 - Alarms: AlarmVector.NoAlarm
10:30:35 - Connection status: False TXclient_alive: False
10:30:35 - Entering set_external_delay
10:30:35 - Setting ExternalDelayLocal to 0.000 ns
10:30:35 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:30:35 - Entering set_external_delay
10:30:35 - Setting ExternalDelayCalibration to 65.000 ns
10:30:35 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:30:35 - Entering set_external_delay
10:30:35 - Setting ExternalDelaySphe to 150.000 ns
10:30:35 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:30:35 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
10:30:35 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:30:35 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:30:35 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:30:35 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:30:35 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:30:35 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:30:35 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:30:35 - Status: TibState.PpsStopped
10:30:35 - Alarms: AlarmVector.NoAlarm
10:30:35 - Connection status: False TXclient_alive: False
10:30:35 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:30:35 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:30:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:30:36 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:30:36 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:30:36 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:30:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:30:36 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:30:36 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:30:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:30:46 - Connecting TIB to camera server at 10.10.4.12:222
10:30:46 - Starting TIB...
10:30:46 - Status: TibState.PpsStopped
10:30:46 - Alarms: AlarmVector.NoAlarm
10:30:46 - Connection status: False TXclient_alive: True
10:30:46 - Resetting run
10:30:46 - Wait for UCTS external trigger before enabling trigger...
10:30:46 - Status: TibState.Standby
10:30:46 - Alarms: AlarmVector.NoAlarm
10:30:46 - Connection status: False TXclient_alive: True
10:30:46 - Status: TibState.Standby
10:30:46 - Alarms: AlarmVector.NoAlarm
10:30:46 - Connection status: False TXclient_alive: True
10:30:47 - Status: TibState.Armed
10:30:47 - Alarms: AlarmVector.NoAlarm
10:30:47 - Connection status: True TXclient_alive: True
10:30:48 - Checking for high voltage locked pixels...
10:30:54 - Starting TIB triggers...
10:30:54 - Enabling trigger
10:30:54 - Status: TibState.Running
10:30:54 - Alarms: AlarmVector.NoAlarm
10:30:54 - Connection status: True TXclient_alive: True
10:30:56 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
10:30:56 - Alarms: AlarmVector.NoAlarm
10:30:56 - Temperature: 33.94
10:30:56 - Local camera rate: 7188.0 Hz
10:30:56 - Stereo trigger rate: 0.0 Hz
10:30:56 - SPE trigger rate: 0.0 Hz
10:30:56 - Calibration trigger rate: 7351.0 Hz
10:30:56 - Software trigger rate: 0.0 Hz
10:30:56 - Pedestal trigger rate: 100.0 Hz
10:30:56 - Collected trigger rate: 7287.0 Hz
10:30:56 - Busy rate: 2.0 Hz
10:30:56 - Camera trigger rate: 7285.0 Hz
10:31:18 - Checking for high voltage locked pixels...
10:31:24 - Stopping TIB...
10:31:24 - Status: TibState.Running
10:31:24 - Alarms: AlarmVector.NoAlarm
10:31:24 - Connection status: True TXclient_alive: True
10:31:24 - Disabling trigger
10:31:24 - Disabling PPS
10:31:25 - Status: TibState.PpsStopped
10:31:25 - Alarms: AlarmVector.NoAlarm
10:31:25 - Connection status: True TXclient_alive: True
10:31:25 - Closing TIB connection to camera server
10:31:29 - Status: TibState.PpsStopped
10:31:29 - Alarms: AlarmVector.NoAlarm
10:31:29 - Connection status: False TXclient_alive: False
10:31:29 - Run duration: 0:00:37
10:31:29 - Local camera triggers: 264508
10:31:29 - Slow control triggers: 0
10:31:29 - Single photo-electron triggers: 0
10:31:29 - Calibration triggers: 270558
10:31:29 - Software triggers from UCTS: 0
10:31:29 - Pedestal triggers: 3659
10:31:29 - Collected input triggers: 221452
10:31:29 - Busy triggers: 97
10:31:29 - Camera event triggers sent to clusters: 221355
10:31:31 - Calling method FSM.gotoReady in object FSM
10:31:33 - Stopping NMC
10:31:33 - Found 0 PPS errors.