15:27:09 - Checking for high voltage locked pixels...
15:27:10 - ("NmcError: Failed to read 'NectarFrontEnd_076.Hvpa.SwitchVoltages': status Bad statuses are present, code 0xffffffff, status NmcStatus.Failed", 4294967295)
15:27:19 - Starting task "Power on channels corresponding to a module to configure"
15:27:19 - Powering on 2 DTC channel(s) corresponding modules listed in /data/config/2021/20210315/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newDACL_newHV2.NMC.xml
15:27:19 - Enabling power in channel 12 of CTDB slot 19
15:27:19 - Enabling power in channel 15 of CTDB slot 19
15:27:19 - Finished task "Power on channels corresponding to a module to configure"
15:27:25 - Stopped periodic check of locked high voltages
15:27:34 - Starting task "Configure modules"
15:27:35 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
15:27:35 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
15:27:35 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
15:27:35 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
15:27:35 - Configuring modules with configuration /data/config/2021/20210315/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newDACL_newHV2.NMC.xml
15:27:35 - Switching off high voltages in configuration
15:27:38 - Successfully configured 2 module(s)
15:27:39 - All front-end boards are programmed with firmware 61210216
15:27:39 - All backplanes are programmed with firmware 15
15:27:39 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
15:27:39 - Found 0 PPS errors.
15:27:39 - Finished task "Configure modules"
15:27:43 - Starting task "Check high voltages"
15:27:43 - Found 0 drawer(s) in Nominal state, 0 in Low state and 2 in Wait state
15:27:43 - Actual voltage is between 0.00 V and 3.66 V.
15:27:43 - Low voltages range between 300.00 V and 300.00 V. 
15:27:44 - Reference voltages range between 984.98 V and 1117.51 V. 
15:27:44 - Maximum difference between expected and actual voltages is 3.66 V
15:27:44 - Maximum of current limits is 4840.96 uA
15:27:44 - Checking status of HVPA module in 2 drawer(s)...
15:27:44 - Checking status of HVPA channels in 2 drawer(s)...
15:27:45 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 14 channel(s)
15:27:45 - Finished task "Check high voltages"
15:28:16 - Updating voltage widget...
15:28:41 - Starting NMC
15:28:41 - Clearing PPS error counters
15:29:08 - Calling method FSM.gotoReady in object FSM
15:29:15 - Calling method FSM.gotoObserving in object FSM
15:30:07 - Checking UCTS clock...
15:30:07 - UCTS and control PC clocks differ by 4.8 seconds
15:30:07 - Configuring UCTS
15:30:07 - Configuring TIB...
15:30:07 - Setting TIB forced mode to False
15:30:07 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:30:08 - Status: TibState.PpsStopped
15:30:08 - Alarms: AlarmVector.ReadError
15:30:08 - Connection status: False TXclient_alive: False
15:30:08 - Entering set_external_delay
15:30:08 - Setting ExternalDelayLocal to 0.000 ns
15:30:08 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:30:08 - Entering set_external_delay
15:30:08 - Setting ExternalDelayCalibration to 65.000 ns
15:30:08 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:30:08 - Entering set_external_delay
15:30:08 - Setting ExternalDelaySphe to 150.000 ns
15:30:08 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:30:08 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
15:30:08 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:30:08 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:30:08 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:30:08 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:30:08 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:30:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:30:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:30:08 - Status: TibState.PpsStopped
15:30:08 - Alarms: AlarmVector.ReadError
15:30:08 - Connection status: False TXclient_alive: False
15:30:08 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:30:08 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:30:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:30:08 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:30:08 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:30:08 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:30:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:30:08 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:30:08 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:30:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:30:10 - Connecting TIB to camera server at 10.10.4.12:222
15:30:10 - Starting TIB...
15:30:10 - Status: TibState.PpsStopped
15:30:10 - Alarms: AlarmVector.ReadError
15:30:10 - Connection status: False TXclient_alive: True
15:30:10 - Resetting run
15:30:10 - Wait for UCTS external trigger before enabling trigger...
15:30:10 - Status: TibState.Standby
15:30:10 - Alarms: AlarmVector.NoAlarm
15:30:10 - Connection status: False TXclient_alive: True
15:30:10 - Status: TibState.Standby
15:30:10 - Alarms: AlarmVector.NoAlarm
15:30:10 - Connection status: False TXclient_alive: True
15:30:11 - Status: TibState.Armed
15:30:11 - Alarms: AlarmVector.NoAlarm
15:30:11 - Connection status: True TXclient_alive: True
15:30:17 - Starting TIB triggers...
15:30:17 - Enabling trigger
15:30:17 - Status: TibState.Running
15:30:17 - Alarms: AlarmVector.ReadError
15:30:17 - Connection status: True TXclient_alive: True
15:31:08 - Stopping TIB...
15:31:08 - Status: TibState.Running
15:31:08 - Alarms: AlarmVector.ReadError
15:31:08 - Connection status: True TXclient_alive: True
15:31:08 - Disabling trigger
15:31:08 - Disabling PPS
15:31:09 - Status: TibState.PpsStopped
15:31:09 - Alarms: AlarmVector.ReadError
15:31:09 - Connection status: True TXclient_alive: True
15:31:09 - Closing TIB connection to camera server
15:31:10 - Status: TibState.PpsStopped
15:31:10 - Alarms: AlarmVector.ReadError
15:31:10 - Connection status: False TXclient_alive: False
15:31:10 - Run duration: 0:00:57
15:31:10 - Local camera triggers: 0
15:31:10 - Slow control triggers: 0
15:31:10 - Single photo-electron triggers: 0
15:31:10 - Calibration triggers: 0
15:31:10 - Software triggers from UCTS: 0
15:31:10 - Pedestal triggers: 56817
15:31:10 - Collected input triggers: 50871
15:31:10 - Busy triggers: 0
15:31:10 - Camera event triggers sent to clusters: 50871
15:31:12 - Calling method FSM.gotoReady in object FSM
15:31:14 - Stopping NMC
15:31:14 - Found 0 PPS errors.