14:52:49 - Starting task "Configure modules"
14:52:49 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
14:52:49 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
14:52:49 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
14:52:49 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
14:52:49 - Configuring modules with configuration /data/config/2021/20210315/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newDACL_newHV2.NMC.xml
14:52:49 - Switching off high voltages in configuration
14:52:53 - Successfully configured 2 module(s)
14:52:53 - All front-end boards are programmed with firmware 61210216
14:52:53 - All backplanes are programmed with firmware 15
14:52:54 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
14:52:54 - Found 0 PPS errors.
14:52:54 - Finished task "Configure modules"
14:53:15 - Starting task "Switch HVPA voltage state"
14:53:15 - Setting HVPA current limit to 12489.75 uA
14:53:15 - Setting HVPA ramp speed to 25 V/s
14:53:15 - Switching HVPA to state Nominal
14:53:22 - Setting HVPA current limits...
14:53:24 - Finished task "Switch HVPA voltage state"
14:53:36 - Updating voltage widget...
14:53:43 - Updating voltage widget...
14:54:11 - Updating voltage widget...
14:54:13 - Updating voltage widget...
14:54:15 - Updating voltage widget...
14:54:30 - Starting task "Check high voltages"
14:54:30 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:54:30 - Actual voltage is between 984.54 V and 1116.91 V.
14:54:30 - Low voltages range between 300.00 V and 300.00 V. 
14:54:31 - Reference voltages range between 984.98 V and 1117.51 V. 
14:54:31 - Maximum difference between expected and actual voltages is 0.45 V
14:54:32 - Maximum of current limits is 4840.96 uA
14:54:32 - Checking status of HVPA module in 2 drawer(s)...
14:54:32 - Checking status of HVPA channels in 2 drawer(s)...
14:54:32 - HV is stabilized in all channels.
14:54:32 - Checking reference and low voltages against /data/config/2021/20210315/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newDACL_newHV2.NMC.xml
14:54:32 - Done
14:54:33 - Finished task "Check high voltages"
14:54:56 - Stopping NMC
14:54:56 - Found 0 PPS errors.
14:54:58 - Starting NMC
14:54:58 - Clearing PPS error counters
14:55:00 - Calling method FSM.gotoObserving in object FSM
14:56:32 - Checking UCTS clock...
14:56:32 - UCTS and control PC clocks differ by 4.9 seconds
14:56:32 - Configuring UCTS
14:56:33 - Configuring TIB...
14:56:33 - Setting TIB forced mode to False
14:56:33 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:56:33 - Status: TibState.PpsStopped
14:56:33 - Alarms: AlarmVector.ReadError
14:56:33 - Connection status: False TXclient_alive: False
14:56:33 - Entering set_external_delay
14:56:33 - Setting ExternalDelayLocal to 0.000 ns
14:56:33 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:56:33 - Entering set_external_delay
14:56:33 - Setting ExternalDelayCalibration to 65.000 ns
14:56:33 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:56:33 - Entering set_external_delay
14:56:33 - Setting ExternalDelaySphe to 150.000 ns
14:56:33 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:56:33 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
14:56:33 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:56:33 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:56:33 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:56:33 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:56:33 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:56:33 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:56:33 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:56:33 - Status: TibState.PpsStopped
14:56:33 - Alarms: AlarmVector.ReadError
14:56:33 - Connection status: False TXclient_alive: False
14:56:33 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:56:33 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:56:34 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:56:34 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:56:34 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:56:34 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:56:34 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:56:34 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:56:34 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:56:34 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:56:41 - Connecting TIB to camera server at 10.10.4.12:222
14:56:41 - Starting TIB...
14:56:41 - Status: TibState.PpsStopped
14:56:41 - Alarms: AlarmVector.ReadError
14:56:41 - Connection status: False TXclient_alive: True
14:56:41 - Resetting run
14:56:41 - Wait for UCTS external trigger before enabling trigger...
14:56:41 - Status: TibState.Standby
14:56:41 - Alarms: AlarmVector.NoAlarm
14:56:41 - Connection status: False TXclient_alive: True
14:56:41 - Status: TibState.Standby
14:56:41 - Alarms: AlarmVector.NoAlarm
14:56:42 - Connection status: False TXclient_alive: True
14:56:43 - Status: TibState.Armed
14:56:43 - Alarms: AlarmVector.NoAlarm
14:56:43 - Connection status: True TXclient_alive: True
14:56:48 - Starting TIB triggers...
14:56:48 - Enabling trigger
14:56:48 - Status: TibState.Running
14:56:48 - Alarms: AlarmVector.ReadError
14:56:48 - Connection status: True TXclient_alive: True
14:57:42 - Stopping TIB...
14:57:42 - Status: TibState.Running
14:57:42 - Alarms: AlarmVector.ReadError
14:57:42 - Connection status: True TXclient_alive: True
14:57:42 - Disabling trigger
14:57:42 - Disabling PPS
14:57:43 - Status: TibState.PpsStopped
14:57:43 - Alarms: AlarmVector.ReadError
14:57:43 - Connection status: True TXclient_alive: True
14:57:43 - Closing TIB connection to camera server
14:57:45 - Status: TibState.PpsStopped
14:57:45 - Alarms: AlarmVector.ReadError
14:57:45 - Connection status: False TXclient_alive: False
14:57:45 - Run duration: 0:00:59
14:57:45 - Local camera triggers: 0
14:57:45 - Slow control triggers: 0
14:57:45 - Single photo-electron triggers: 0
14:57:45 - Calibration triggers: 0
14:57:45 - Software triggers from UCTS: 0
14:57:45 - Pedestal triggers: 58903
14:57:45 - Collected input triggers: 53929
14:57:45 - Busy triggers: 0
14:57:45 - Camera event triggers sent to clusters: 53929