15:44:11 - Resetting NMC
15:44:12 - Starting task "Configure modules"
15:44:12 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
15:44:12 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
15:44:12 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
15:44:12 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
15:44:12 - Configuring modules with configuration /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newHV2.NMC.xml
15:44:12 - Switching off high voltages in configuration
15:44:14 - Checking for high voltage locked pixels...
15:44:16 - Successfully configured 2 module(s)
15:44:16 - All front-end boards are programmed with firmware 61201223
15:44:16 - All backplanes are programmed with firmware 15
15:44:17 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
15:44:17 - Found 0 PPS errors.
15:44:17 - Finished task "Configure modules"
15:44:20 - Starting task "Switch HVPA voltage state"
15:44:20 - Setting HVPA current limit to 12489.75 uA
15:44:20 - Setting HVPA ramp speed to 25 V/s
15:44:20 - Switching HVPA to state Nominal
15:44:26 - Calling method FSM.gotoObserving in object FSM
15:44:27 - Setting HVPA current limits...
15:44:29 - Finished task "Switch HVPA voltage state"
15:44:43 - Updating voltage widget...
15:44:44 - Checking for high voltage locked pixels...
15:44:47 - Starting task "Check high voltages"
15:44:47 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:44:48 - Actual voltage is between 986.37 V and 1125.45 V.
15:44:48 - Low voltages range between 300.00 V and 300.00 V. 
15:44:48 - Reference voltages range between 986.23 V and 1125.46 V. 
15:44:49 - Maximum difference between expected and actual voltages is 0.54 V
15:44:49 - Maximum of current limits is 4840.96 uA
15:44:49 - Checking status of HVPA module in 2 drawer(s)...
15:44:49 - Checking status of HVPA channels in 2 drawer(s)...
15:44:50 - HV is stabilized in all channels.
15:44:50 - Checking reference and low voltages against /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong_DelayBusy0_newHV2.NMC.xml
15:44:50 - Done
15:44:50 - Finished task "Check high voltages"
15:44:52 - Starting NMC
15:44:52 - Clearing PPS error counters
15:45:12 - Checking UCTS clock...
15:45:13 - UCTS clock is late by -7 seconds!
15:45:13 - Configuring UCTS
15:45:13 - Configuring TIB...
15:45:13 - Setting TIB forced mode to False
15:45:13 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:45:13 - Status: TibState.PpsStopped
15:45:13 - Alarms: AlarmVector.BufferFull|AlmostFull
15:45:13 - Connection status: False TXclient_alive: False
15:45:13 - Entering set_external_delay
15:45:13 - Setting ExternalDelayLocal to 0.000 ns
15:45:13 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:45:13 - Entering set_external_delay
15:45:13 - Setting ExternalDelayCalibration to 65.000 ns
15:45:13 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:45:13 - Entering set_external_delay
15:45:13 - Setting ExternalDelaySphe to 150.000 ns
15:45:13 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:45:13 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:45:13 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:45:13 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:45:13 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:45:13 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:45:13 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:45:13 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:45:14 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:45:14 - Status: TibState.PpsStopped
15:45:14 - Alarms: AlarmVector.BufferFull|AlmostFull
15:45:14 - Connection status: False TXclient_alive: False
15:45:14 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:45:14 - Writing 9000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:45:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:45:14 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:45:14 - Writing 9000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:45:14 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:45:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:45:14 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:45:14 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:45:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:45:14 - Checking for high voltage locked pixels...
15:45:14 - Connecting TIB to camera server at 10.10.4.12:222
15:45:14 - Starting TIB...
15:45:14 - Status: TibState.PpsStopped
15:45:14 - Alarms: AlarmVector.BufferFull|AlmostFull
15:45:14 - Connection status: False TXclient_alive: False
15:45:14 - Resetting run
15:45:14 - Wait for UCTS external trigger before enabling trigger...
15:45:14 - Status: TibState.Standby
15:45:14 - Alarms: AlarmVector.NoAlarm
15:45:15 - Connection status: False TXclient_alive: True
15:45:15 - Status: TibState.Standby
15:45:15 - Alarms: AlarmVector.NoAlarm
15:45:15 - Connection status: False TXclient_alive: True
15:45:16 - Status: TibState.Armed
15:45:16 - Alarms: AlarmVector.NoAlarm
15:45:16 - Connection status: False TXclient_alive: True
15:45:16 - Starting TIB triggers...
15:45:16 - Enabling trigger
15:45:16 - Status: TibState.Running
15:45:16 - Alarms: AlarmVector.NoAlarm
15:45:17 - Connection status: False TXclient_alive: True
15:45:20 - Configuring calibration box...
15:45:20 - Configuring calibration box with leds=0x40 voltage=9.50 frequency=1000.0/1 central_current=0.0 duration=510 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
15:45:21 - Starting flashes...
15:45:44 - Checking for high voltage locked pixels...
15:46:14 - Checking for high voltage locked pixels...
15:46:16 - Stopping TIB...
15:46:16 - Status: TibState.Running
15:46:16 - Alarms: AlarmVector.BufferFull|AlmostFull
15:46:16 - Connection status: False TXclient_alive: True
15:46:16 - Disabling trigger
15:46:16 - Disabling PPS
15:46:17 - Status: TibState.PpsStopped
15:46:17 - Alarms: AlarmVector.BufferFull|AlmostFull
15:46:17 - Connection status: False TXclient_alive: True
15:46:17 - Closing TIB connection to camera server
15:46:18 - Status: TibState.PpsStopped
15:46:18 - Alarms: AlarmVector.BufferFull|AlmostFull
15:46:18 - Connection status: False TXclient_alive: False
15:46:18 - Run duration: 0:01:01
15:46:18 - Local camera triggers: 0
15:46:18 - Slow control triggers: 0
15:46:18 - Single photo-electron triggers: 9
15:46:18 - Calibration triggers: 50948
15:46:18 - Software triggers from UCTS: 0
15:46:18 - Pedestal triggers: 0
15:46:18 - Collected input triggers: 50947
15:46:18 - Busy triggers: 0
15:46:18 - Camera event triggers sent to clusters: 50947
15:46:20 - Calling method FSM.gotoReady in object FSM
15:46:23 - Stopping NMC
15:46:23 - Found 0 PPS errors.