14:37:05 - Starting task "Configure modules"
14:37:05 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
14:37:05 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
14:37:05 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
14:37:05 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
14:37:05 - Configuring modules with configuration /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong_DelayBusy0.NMC.xml
14:37:05 - Switching off high voltages in configuration
14:37:09 - Successfully configured 2 module(s)
14:37:09 - All front-end boards are programmed with firmware 61201223
14:37:09 - All backplanes are programmed with firmware 15
14:37:10 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
14:37:10 - Found 0 PPS errors.
14:37:10 - Finished task "Configure modules"
14:37:14 - Checking status of calibration box...
14:37:15 - Calibration box is configured with 0 leds at a frequency of 200.0 Hz and a voltage of 8.00 V
14:37:50 - Configuring calibration box...
14:37:50 - Configuring calibration box with leds=0x1fff voltage=9.50 frequency=1000.0/1 central_current=0.0 duration=510 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:37:55 - Starting task "Switch HVPA voltage state"
14:37:55 - Setting HVPA current limit to 12489.75 uA
14:37:56 - Setting HVPA ramp speed to 25 V/s
14:37:56 - Switching HVPA to state Low
14:38:03 - Setting HVPA current limits...
14:38:04 - Finished task "Switch HVPA voltage state"
14:40:11 - High voltage locked channels will be checked every 30 s
14:40:14 - Starting task "Switch HVPA voltage state"
14:40:14 - Setting HVPA current limit to 12489.75 uA
14:40:15 - Setting HVPA ramp speed to 25 V/s
14:40:15 - Switching HVPA to state Nominal
14:40:22 - Setting HVPA current limits...
14:40:23 - Finished task "Switch HVPA voltage state"
14:40:34 - Updating voltage widget...
14:40:36 - Updating voltage widget...
14:40:41 - Updating voltage widget...
14:40:42 - Checking for high voltage locked pixels...
14:40:43 - Updating voltage widget...
14:40:48 - Starting task "Check high voltages"
14:40:48 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:40:48 - Actual voltage is between 989.42 V and 1167.54 V.
14:40:48 - Low voltages range between 300.00 V and 300.00 V. 
14:40:49 - Reference voltages range between 989.87 V and 1168.35 V. 
14:40:49 - Maximum difference between expected and actual voltages is 0.52 V
14:40:50 - Maximum of current limits is 4840.96 uA
14:40:50 - Checking status of HVPA module in 2 drawer(s)...
14:40:50 - Checking status of HVPA channels in 2 drawer(s)...
14:40:50 - HV is stabilized in all channels.
14:40:50 - Checking reference and low voltages against /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong_DelayBusy0.NMC.xml
14:40:50 - Done
14:40:50 - Finished task "Check high voltages"
14:41:12 - Checking for high voltage locked pixels...
14:41:35 - Starting NMC
14:41:35 - Clearing PPS error counters
14:41:39 - Calling method FSM.gotoObserving in object FSM
14:41:42 - Checking for high voltage locked pixels...
14:42:03 - Resetting TIB...
14:42:06 - Could not invoke the MethodCall service: BadTimeout
14:42:12 - Checking for high voltage locked pixels...
14:42:12 - Checking UCTS clock...
14:42:12 - UCTS clock is late by -7 seconds!
14:42:12 - Configuring UCTS
14:42:13 - Configuring TIB...
14:42:13 - Setting TIB forced mode to False
14:42:13 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:42:13 - Status: TibState.RunStopped
14:42:13 - Alarms: AlarmVector.NoAlarm
14:42:13 - Connection status: False TXclient_alive: False
14:42:13 - Disabling PPS
14:42:15 - Status: TibState.PpsStopped
14:42:15 - Alarms: AlarmVector.NoAlarm
14:42:15 - Connection status: False TXclient_alive: False
14:42:15 - Entering set_external_delay
14:42:15 - Setting ExternalDelayLocal to 0.000 ns
14:42:15 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:42:15 - Entering set_external_delay
14:42:15 - Setting ExternalDelayCalibration to 65.000 ns
14:42:15 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:42:15 - Entering set_external_delay
14:42:15 - Setting ExternalDelaySphe to 150.000 ns
14:42:15 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:42:15 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
14:42:15 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:42:15 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:42:15 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:42:15 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:42:15 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:42:15 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:42:15 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:42:15 - Status: TibState.PpsStopped
14:42:15 - Alarms: AlarmVector.NoAlarm
14:42:15 - Connection status: False TXclient_alive: False
14:42:15 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:42:15 - Writing 9000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:42:15 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:42:15 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:42:15 - Writing 9000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:42:15 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:42:15 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:42:15 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:42:15 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:42:15 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:42:19 - Connecting TIB to camera server at 10.10.4.12:222
14:42:19 - Starting TIB...
14:42:19 - Status: TibState.PpsStopped
14:42:19 - Alarms: AlarmVector.NoAlarm
14:42:19 - Connection status: False TXclient_alive: True
14:42:19 - Resetting run
14:42:19 - Wait for UCTS external trigger before enabling trigger...
14:42:19 - Status: TibState.Standby
14:42:19 - Alarms: AlarmVector.NoAlarm
14:42:19 - Connection status: False TXclient_alive: True
14:42:19 - Status: TibState.Standby
14:42:19 - Alarms: AlarmVector.NoAlarm
14:42:19 - Connection status: False TXclient_alive: True
14:42:20 - Status: TibState.Armed
14:42:20 - Alarms: AlarmVector.NoAlarm
14:42:20 - Connection status: False TXclient_alive: True
14:42:26 - Starting TIB triggers...
14:42:26 - Enabling trigger
14:42:26 - Status: TibState.Running
14:42:26 - Alarms: AlarmVector.NoAlarm
14:42:26 - Connection status: False TXclient_alive: True
14:42:42 - Checking for high voltage locked pixels...
14:42:50 - Configuring calibration box...
14:42:50 - Configuring calibration box with leds=0x40 voltage=9.50 frequency=1000.0/1 central_current=0.0 duration=510 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:42:56 - Starting flashes...
14:43:12 - Checking for high voltage locked pixels...
14:43:42 - Checking for high voltage locked pixels...
14:43:54 - Stopping TIB...
14:43:54 - Status: TibState.Running
14:43:54 - Alarms: AlarmVector.BufferFull|AlmostFull
14:43:54 - Connection status: False TXclient_alive: True
14:43:54 - Disabling trigger
14:43:54 - Disabling PPS
14:43:55 - Status: TibState.PpsStopped
14:43:55 - Alarms: AlarmVector.BufferFull|AlmostFull
14:43:55 - Connection status: False TXclient_alive: True
14:43:55 - Closing TIB connection to camera server
14:43:56 - Status: TibState.PpsStopped
14:43:56 - Alarms: AlarmVector.BufferFull|AlmostFull
14:43:56 - Connection status: False TXclient_alive: False
14:43:56 - Run duration: 0:01:34
14:43:56 - Local camera triggers: 0
14:43:56 - Slow control triggers: 0
14:43:56 - Single photo-electron triggers: 8
14:43:56 - Calibration triggers: 50981
14:43:56 - Software triggers from UCTS: 0
14:43:56 - Pedestal triggers: 0
14:43:56 - Collected input triggers: 50981
14:43:56 - Busy triggers: 0
14:43:56 - Camera event triggers sent to clusters: 50981
14:43:58 - Calling method FSM.gotoReady in object FSM
14:44:01 - Stopping NMC
14:44:01 - Found 0 PPS errors.²:wq