09:26:49 - Starting task "Power on channels corresponding to a module to configure"
09:26:49 - Powering on 2 DTC channel(s) corresponding modules listed in /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong.NMC.xml
09:26:49 - Enabling power in channel 12 of CTDB slot 19
09:26:49 - Enabling power in channel 15 of CTDB slot 19
09:26:50 - Finished task "Power on channels corresponding to a module to configure"
09:26:53 - Scanning interface enp2s0 for non configured modules...
09:26:56 - Found 2 MAC address(es)
09:27:03 - Starting task "Configure modules"
09:27:03 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
09:27:03 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
09:27:03 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
09:27:03 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
09:27:03 - Configuring modules with configuration /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong.NMC.xml
09:27:03 - Switching off high voltages in configuration
09:27:06 - Successfully configured 2 module(s)
09:27:07 - All front-end boards are programmed with firmware 61201223
09:27:07 - All backplanes are programmed with firmware 15
09:27:08 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
09:27:08 - Found 0 PPS errors.
09:27:08 - Finished task "Configure modules"
09:28:02 - Status: TibState.RunStopped ConnectionStatus: False TXclient_alive: False
09:28:02 - Alarms: AlarmVector.BufferFull
09:28:02 - Temperature: 32.12
09:28:02 - Local camera rate: 0.0 Hz
09:28:02 - Stereo trigger rate: 0.0 Hz
09:28:02 - SPE trigger rate: 0.0 Hz
09:28:02 - Calibration trigger rate: 9329.0 Hz
09:28:02 - Software trigger rate: 0.0 Hz
09:28:02 - Pedestal trigger rate: 0.0 Hz
09:28:02 - Collected trigger rate: 0.0 Hz
09:28:02 - Busy rate: 0.0 Hz
09:28:02 - Camera trigger rate: 0.0 Hz
09:28:27 - Stopping flashes...
09:28:32 - Starting task "Switch HVPA voltage state"
09:28:33 - Setting HVPA current limit to 12489.75 uA
09:28:33 - Setting HVPA ramp speed to 25 V/s
09:28:33 - Switching HVPA to state Low
09:28:40 - High voltage locked channels will be checked every 30 s
09:28:40 - Setting HVPA current limits...
09:28:42 - Finished task "Switch HVPA voltage state"
09:28:52 - Updating voltage widget...
09:28:56 - Starting task "Switch HVPA voltage state"
09:28:56 - Setting HVPA current limit to 12489.75 uA
09:28:56 - Setting HVPA ramp speed to 25 V/s
09:28:57 - Switching HVPA to state Nominal
09:29:04 - Setting HVPA current limits...
09:29:05 - Finished task "Switch HVPA voltage state"
09:29:11 - Checking for high voltage locked pixels...
09:29:36 - Updating voltage widget...
09:29:40 - Starting task "Check high voltages"
09:29:40 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
09:29:40 - Actual voltage is between 989.42 V and 1168.15 V.
09:29:40 - Low voltages range between 300.00 V and 300.00 V. 
09:29:41 - Checking for high voltage locked pixels...
09:29:41 - Reference voltages range between 989.87 V and 1168.35 V. 
09:29:41 - Maximum difference between expected and actual voltages is 0.60 V
09:29:42 - Maximum of current limits is 4840.96 uA
09:29:42 - Checking status of HVPA module in 2 drawer(s)...
09:29:42 - Checking status of HVPA channels in 2 drawer(s)...
09:29:42 - HV is stabilized in all channels.
09:29:42 - Checking reference and low voltages against /data/config/2021/20210127/config_tower_2modules_FEBv6_pingpong.NMC.xml
09:29:42 - Done
09:29:42 - Finished task "Check high voltages"
09:29:44 - Starting NMC
09:29:44 - Clearing PPS error counters
09:29:47 - Calling method FSM.gotoReady in object FSM
09:29:53 - Calling method FSM.gotoObserving in object FSM
09:30:11 - Checking for high voltage locked pixels...
09:30:17 - Checking UCTS clock...
09:30:17 - UCTS clock is late by -7 seconds!
09:30:17 - Configuring UCTS
09:30:18 - Configuring TIB...
09:30:18 - Setting TIB forced mode to False
09:30:18 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
09:30:18 - Status: TibState.RunStopped
09:30:18 - Alarms: AlarmVector.BufferFull
09:30:18 - Connection status: False TXclient_alive: False
09:30:18 - Disabling PPS
09:30:20 - Status: TibState.PpsStopped
09:30:20 - Alarms: AlarmVector.BufferFull
09:30:20 - Connection status: False TXclient_alive: False
09:30:20 - Entering set_external_delay
09:30:20 - Setting ExternalDelayLocal to 0.000 ns
09:30:20 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
09:30:21 - Entering set_external_delay
09:30:21 - Setting ExternalDelayCalibration to 65.000 ns
09:30:21 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
09:30:21 - Entering set_external_delay
09:30:21 - Setting ExternalDelaySphe to 150.000 ns
09:30:21 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
09:30:21 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
09:30:21 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
09:30:21 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
09:30:21 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
09:30:21 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
09:30:21 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
09:30:21 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
09:30:21 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
09:30:21 - Status: TibState.PpsStopped
09:30:21 - Alarms: AlarmVector.BufferFull
09:30:21 - Connection status: False TXclient_alive: False
09:30:21 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
09:30:21 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
09:30:21 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:30:21 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
09:30:21 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
09:30:21 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
09:30:21 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:30:21 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
09:30:21 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
09:30:21 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:30:22 - Connecting TIB to camera server at 10.10.4.12:222
09:30:22 - Starting TIB...
09:30:22 - Status: TibState.PpsStopped
09:30:22 - Alarms: AlarmVector.BufferFull
09:30:22 - Connection status: False TXclient_alive: False
09:30:22 - Resetting run
09:30:22 - Wait for UCTS external trigger before enabling trigger...
09:30:22 - Status: TibState.Standby
09:30:22 - Alarms: AlarmVector.NoAlarm
09:30:23 - Connection status: False TXclient_alive: True
09:30:23 - Status: TibState.Standby
09:30:23 - Alarms: AlarmVector.NoAlarm
09:30:23 - Connection status: False TXclient_alive: True
09:30:24 - Status: TibState.Armed
09:30:24 - Alarms: AlarmVector.NoAlarm
09:30:24 - Connection status: True TXclient_alive: True
09:30:25 - Starting TIB triggers...
09:30:25 - Enabling trigger
09:30:25 - Status: TibState.Running
09:30:25 - Alarms: AlarmVector.NoAlarm
09:30:25 - Connection status: True TXclient_alive: True
09:30:41 - Checking for high voltage locked pixels...
09:30:49 - Checking status of calibration box...
09:30:51 - Calibration box is configured with 13 leds at a frequency of 200.0 Hz and a voltage of 16.50 V
09:31:11 - Checking for high voltage locked pixels...
09:31:27 - Configuring calibration box...
09:31:27 - Configuring calibration box with leds=0x1fff voltage=16.50 frequency=400.0/2 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
09:31:41 - Checking for high voltage locked pixels...
09:32:11 - Checking for high voltage locked pixels...
09:32:41 - Checking for high voltage locked pixels...
09:33:11 - Checking for high voltage locked pixels...
09:33:15 - Stopping TIB...
09:33:15 - Status: TibState.Running
09:33:15 - Alarms: AlarmVector.NoAlarm
09:33:15 - Connection status: True TXclient_alive: True
09:33:15 - Disabling trigger
09:33:16 - Disabling PPS
09:33:17 - Status: TibState.PpsStopped
09:33:17 - Alarms: AlarmVector.NoAlarm
09:33:17 - Connection status: True TXclient_alive: True
09:33:17 - Closing TIB connection to camera server
09:33:18 - Status: TibState.PpsStopped
09:33:18 - Alarms: AlarmVector.NoAlarm
09:33:18 - Connection status: False TXclient_alive: False
09:33:18 - Run duration: 0:02:52
09:33:18 - Local camera triggers: 0
09:33:18 - Slow control triggers: 0
09:33:18 - Single photo-electron triggers: 0
09:33:18 - Calibration triggers: 1593103
09:33:18 - Software triggers from UCTS: 0
09:33:18 - Pedestal triggers: 0
09:33:18 - Collected input triggers: 1575065
09:33:18 - Busy triggers: 11754
09:33:18 - Camera event triggers sent to clusters: 1563311
09:33:20 - Calling method FSM.gotoReady in object FSM
09:33:23 - Stopping NMC
09:33:23 - Found 0 PPS errors.