16:29:09 - ECC is in state EccState.Safe with status EccStatus.NoError
16:29:09 - Average temperature: 20.5 deg C
16:29:09 - Air temperature (T1-T6 and T9-T10): 20.5, -838.0, -838.0, 1254.0, 1254.0, 1254.0, -838.0, -838.0 deg C
16:29:09 - Air differential pressure: 0.0 Pa
16:29:09 - Water temperature (T11-T12): -838.0, -838.0 deg C
16:29:09 - Back doors are closed.
16:29:09 - Shutter is in state PartiallyOpen (error 0)
16:29:09 - Light sensors: [1.64, 1.96, 2.25, 2.51] V
16:29:09 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:29:09 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:29:09 - 24 V power supply no. 1 is disabled with a current of 6.210 A.
16:29:21 - Starting task "Prepare ECC"
16:29:21 - Preparing ECC...
16:29:21 - Setting ECC temperature range for Ready state to [16.000000, 36.000000]
16:29:21 - Setting ECC mode to EccTransition.Ready
16:29:22 - Received ECC state change notification: EccState.Safe
16:29:27 - Received ECC state change notification: EccState.Ready
16:29:28 - Setting power supply box SPE relay to True
16:29:28 - Finished task "Prepare ECC"
16:33:57 - Starting task "Configure modules"
16:33:57 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
16:33:57 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
16:33:57 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
16:33:57 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
16:33:57 - Configuring modules with configuration /data/config/2020/20201208/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy7.NMC.xml
16:33:57 - Switching off high voltages in configuration
16:33:58 - ("NmcError: Failed to call 'Configure': status Bad statuses are present, code 0xfffffffe, status NmcStatus.Timeout", 4294967294)
16:33:58 - NMC is in state NmcState.Ready and knows of 0 drawer(s)
16:33:59 - Found 0 PPS errors.
16:33:59 - Finished task "Configure modules"
16:34:03 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:03 - Average temperature: 20.6 deg C
16:34:03 - Air temperature (T1-T6 and T9-T10): 20.6, 1255.0, 1254.0, 1254.0, -838.0, -838.0, -838.0, 1253.0 deg C
16:34:03 - Air differential pressure: 0.0 Pa
16:34:03 - Water temperature (T11-T12): -838.0, 1254.0 deg C
16:34:03 - Back doors are closed.
16:34:03 - Shutter is in state PartiallyOpen (error 0)
16:34:03 - Light sensors: [1.63, 1.95, 2.24, 2.5] V
16:34:03 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:03 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:03 - 24 V power supply no. 1 is enabled with a current of 0.450 A.
16:34:08 - Starting task "Powering modules..."
16:34:08 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_on' on Digital Trigger Crate at 10.10.4.57
16:34:10 - Finished task "Powering modules..."
16:34:11 - Starting task "Powering modules..."
16:34:11 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
16:34:13 - Finished task "Powering modules..."
16:34:17 - Starting task "Powering modules..."
16:34:17 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_on' on Digital Trigger Crate at 10.10.4.57
16:34:19 - Finished task "Powering modules..."
16:34:21 - Module 85 is connected to channel 15 of DTC slot 19
16:34:24 - Starting task "Powering modules..."
16:34:24 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
16:34:25 - Finished task "Powering modules..."
16:34:27 - Starting task "Powering modules..."
16:34:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_on' on Digital Trigger Crate at 10.10.4.57
16:34:29 - Finished task "Powering modules..."
16:34:32 - Scanning interface enp2s0 for non configured modules...
16:34:32 - Found 1 MAC address(es)
16:34:33 - Scanning interface enp2s0 for non configured modules...
16:34:34 - Found 1 MAC address(es)
16:34:34 - Scanning interface enp2s0 for non configured modules...
16:34:35 - Found 2 MAC address(es)
16:34:39 - Starting task "Configure modules"
16:34:39 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
16:34:39 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
16:34:39 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
16:34:39 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
16:34:39 - Configuring modules with configuration /data/config/2020/20201208/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy7.NMC.xml
16:34:39 - Switching off high voltages in configuration
16:34:42 - Successfully configured 2 module(s)
16:34:43 - All front-end boards are programmed with firmware 61201209
16:34:43 - All backplanes are programmed with firmware 15
16:34:44 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:34:44 - Found 0 PPS errors.
16:34:44 - Finished task "Configure modules"
16:34:47 - Starting NMC
16:34:47 - Clearing PPS error counters
16:34:51 - Stopping NMC
16:34:51 - Found 0 PPS errors.
16:34:58 - Starting task "Configure modules"
16:34:58 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
16:34:58 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
16:34:58 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
16:34:58 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
16:34:58 - Configuring modules with configuration /data/config/2020/20201208/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy4_newDacl.NMC.xml
16:34:58 - Switching off high voltages in configuration
16:35:01 - Successfully configured 2 module(s)
16:35:02 - All front-end boards are programmed with firmware 61201209
16:35:02 - All backplanes are programmed with firmware 15
16:35:02 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:35:02 - Found 0 PPS errors.
16:35:03 - Finished task "Configure modules"
16:35:05 - Starting NMC
16:35:05 - Clearing PPS error counters
16:35:16 - Calling method FSM.gotoObserving in object FSM
16:35:34 - Checking UCTS clock...
16:35:35 - UCTS and control PC clocks differ by 4.2 seconds
16:35:35 - Configuring UCTS
16:35:35 - Configuring TIB...
16:35:35 - Setting TIB forced mode to False
16:35:35 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:35:35 - Status: TibState.RunStopped
16:35:35 - Alarms: AlarmVector.BufferFull
16:35:35 - Connection status: False TXclient_alive: False
16:35:35 - Disabling PPS
16:35:37 - Status: TibState.PpsStopped
16:35:37 - Alarms: AlarmVector.BufferFull
16:35:37 - Connection status: False TXclient_alive: False
16:35:37 - Entering set_external_delay
16:35:37 - Setting ExternalDelayLocal to 0.000 ns
16:35:37 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:35:37 - Entering set_external_delay
16:35:37 - Setting ExternalDelayCalibration to 65.000 ns
16:35:37 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:35:37 - Entering set_external_delay
16:35:37 - Setting ExternalDelaySphe to 150.000 ns
16:35:37 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:35:37 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
16:35:37 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:35:37 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:35:37 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:35:37 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:35:37 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:35:37 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:35:37 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:35:38 - Status: TibState.PpsStopped
16:35:38 - Alarms: AlarmVector.BufferFull
16:35:38 - Connection status: False TXclient_alive: False
16:35:38 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:35:38 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:35:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:35:38 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:35:38 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:35:38 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:35:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:35:38 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:35:38 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:35:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:35:40 - Connecting TIB to camera server at 10.10.4.12:222
16:35:40 - Starting TIB...
16:35:40 - Status: TibState.PpsStopped
16:35:40 - Alarms: AlarmVector.BufferFull
16:35:40 - Connection status: False TXclient_alive: False
16:35:40 - Resetting run
16:35:40 - Wait for UCTS external trigger before enabling trigger...
16:35:40 - Status: TibState.Standby
16:35:40 - Alarms: AlarmVector.NoAlarm
16:35:40 - Connection status: False TXclient_alive: True
16:35:40 - Status: TibState.Standby
16:35:40 - Alarms: AlarmVector.NoAlarm
16:35:40 - Connection status: False TXclient_alive: True
16:35:41 - Status: TibState.Armed
16:35:41 - Alarms: AlarmVector.NoAlarm
16:35:41 - Connection status: True TXclient_alive: True
16:35:44 - Starting TIB triggers...
16:35:44 - Enabling trigger
16:35:44 - Status: TibState.Running
16:35:44 - Alarms: AlarmVector.NoAlarm
16:35:44 - Connection status: True TXclient_alive: True
16:35:47 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
16:35:47 - Alarms: AlarmVector.NoAlarm
16:35:47 - Temperature: 34.06
16:35:47 - Local camera rate: 0.0 Hz
16:35:47 - Stereo trigger rate: 0.0 Hz
16:35:47 - SPE trigger rate: 0.0 Hz
16:35:47 - Calibration trigger rate: 8566.0 Hz
16:35:47 - Software trigger rate: 0.0 Hz
16:35:47 - Pedestal trigger rate: 100.0 Hz
16:35:47 - Collected trigger rate: 8611.0 Hz
16:35:47 - Busy rate: 47.0 Hz
16:35:47 - Camera trigger rate: 8564.0 Hz
16:35:50 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
16:35:50 - Alarms: AlarmVector.NoAlarm
16:35:50 - Temperature: 34.06
16:35:50 - Local camera rate: 0.0 Hz
16:35:50 - Stereo trigger rate: 0.0 Hz
16:35:50 - SPE trigger rate: 0.0 Hz
16:35:50 - Calibration trigger rate: 8529.0 Hz
16:35:50 - Software trigger rate: 0.0 Hz
16:35:50 - Pedestal trigger rate: 100.0 Hz
16:35:50 - Collected trigger rate: 8576.0 Hz
16:35:50 - Busy rate: 40.0 Hz
16:35:50 - Camera trigger rate: 8536.0 Hz
16:36:44 - Stopping TIB...
16:36:44 - Status: TibState.Running
16:36:44 - Alarms: AlarmVector.NoAlarm
16:36:44 - Connection status: True TXclient_alive: True
16:36:44 - Disabling trigger
16:36:44 - Disabling PPS
16:36:45 - Status: TibState.PpsStopped
16:36:45 - Alarms: AlarmVector.NoAlarm
16:36:45 - Connection status: True TXclient_alive: True
16:36:45 - Closing TIB connection to camera server
16:36:47 - Status: TibState.PpsStopped
16:36:47 - Alarms: AlarmVector.NoAlarm
16:36:47 - Connection status: False TXclient_alive: False
16:36:47 - Run duration: 0:01:02
16:36:47 - Local camera triggers: 0
16:36:47 - Slow control triggers: 0
16:36:47 - Single photo-electron triggers: 0
16:36:47 - Calibration triggers: 525721
16:36:47 - Software triggers from UCTS: 0
16:36:47 - Pedestal triggers: 6181
16:36:47 - Collected input triggers: 512194
16:36:47 - Busy triggers: 2790
16:36:47 - Camera event triggers sent to clusters: 509404
16:36:53 - Calling method FSM.gotoReady in object FSM
16:36:58 - Stopping NMC
16:36:58 - Found 0 PPS errors.