10:23:56 - Stopping flashes...
10:25:41 - Resetting NMC
10:25:44 - Starting task "Powering modules..."
10:25:44 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:25:46 - Finished task "Powering modules..."
10:25:47 - Starting task "Powering modules..."
10:25:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_on' on Digital Trigger Crate at 10.10.4.57
10:25:49 - Finished task "Powering modules..."
10:25:50 - Module 84 is connected to channel 12 of DTC slot 19
10:25:52 - Starting task "Powering modules..."
10:25:52 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:25:54 - Finished task "Powering modules..."
10:25:55 - Starting task "Powering modules..."
10:25:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_on' on Digital Trigger Crate at 10.10.4.57
10:25:57 - Finished task "Powering modules..."
10:26:04 - Starting task "Configure modules"
10:26:04 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
10:26:04 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
10:26:04 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
10:26:04 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
10:26:04 - Configuring modules with configuration /data/config/2020/20201208/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy8.NMC.xml
10:26:04 - Switching off high voltages in configuration
10:26:07 - Successfully configured 2 module(s)
10:26:08 - All front-end boards are programmed with firmware 61201208
10:26:08 - All backplanes are programmed with firmware 15
10:26:08 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
10:26:08 - Found 0 PPS errors.
10:26:09 - Finished task "Configure modules"
10:26:15 - Starting task "Switch HVPA voltage state"
10:26:15 - Setting HVPA current limit to 12489.75 uA
10:26:15 - Setting HVPA ramp speed to 500 V/s
10:26:15 - Switching HVPA to state Low
10:26:17 - High voltage locked channels will be checked every 30 s
10:26:22 - Setting HVPA current limits...
10:26:24 - Finished task "Switch HVPA voltage state"
10:26:27 - Updating voltage widget...
10:26:32 - Updating voltage widget...
10:26:36 - Starting task "Switch HVPA voltage state"
10:26:36 - Setting HVPA current limit to 12489.75 uA
10:26:36 - Setting HVPA ramp speed to 25 V/s
10:26:36 - Switching HVPA to state Nominal
10:26:44 - Setting HVPA current limits...
10:26:45 - Finished task "Switch HVPA voltage state"
10:26:48 - Checking for high voltage locked pixels...
10:27:09 - Calling method FSM.gotoObserving in object FSM
10:27:11 - Updating voltage widget...
10:27:14 - Starting task "Check high voltages"
10:27:14 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:27:14 - Actual voltage is between 990.03 V and 1168.15 V.
10:27:14 - Low voltages range between 300.00 V and 300.00 V. 
10:27:15 - Reference voltages range between 989.87 V and 1168.35 V. 
10:27:15 - Maximum difference between expected and actual voltages is 0.52 V
10:27:15 - Maximum of current limits is 4840.96 uA
10:27:15 - Checking status of HVPA module in 2 drawer(s)...
10:27:15 - Checking status of HVPA channels in 2 drawer(s)...
10:27:16 - HV is stabilized in all channels.
10:27:16 - Checking reference and low voltages against /data/config/2020/20201208/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy8.NMC.xml
10:27:16 - Done
10:27:16 - Finished task "Check high voltages"
10:27:18 - Checking for high voltage locked pixels...
10:27:19 - Starting NMC
10:27:19 - Clearing PPS error counters
10:27:28 - Configuring calibration box...
10:27:28 - Configuring calibration box with leds=0x40 voltage=15.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
10:27:33 - Checking UCTS clock...
10:27:33 - UCTS and control PC clocks differ by 3.7 seconds
10:27:33 - Configuring UCTS
10:27:33 - Configuring TIB...
10:27:33 - Setting TIB forced mode to False
10:27:33 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:27:33 - Status: TibState.PpsStopped
10:27:33 - Alarms: AlarmVector.NoAlarm
10:27:33 - Connection status: False TXclient_alive: False
10:27:33 - Entering set_external_delay
10:27:33 - Setting ExternalDelayLocal to 0.000 ns
10:27:33 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:27:34 - Entering set_external_delay
10:27:34 - Setting ExternalDelayCalibration to 65.000 ns
10:27:34 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:27:35 - Entering set_external_delay
10:27:35 - Setting ExternalDelaySphe to 150.000 ns
10:27:35 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:27:35 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
10:27:35 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:27:35 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:27:35 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:27:35 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:27:35 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:27:35 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:27:35 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:27:35 - Status: TibState.PpsStopped
10:27:35 - Alarms: AlarmVector.NoAlarm
10:27:35 - Connection status: False TXclient_alive: False
10:27:35 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:27:35 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:27:35 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:27:35 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:27:35 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:27:35 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:27:35 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:27:35 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:27:35 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:27:35 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:27:37 - Connecting TIB to camera server at 10.10.4.12:222
10:27:37 - Starting TIB...
10:27:37 - Status: TibState.PpsStopped
10:27:37 - Alarms: AlarmVector.NoAlarm
10:27:37 - Connection status: False TXclient_alive: True
10:27:37 - Resetting run
10:27:37 - Wait for UCTS external trigger before enabling trigger...
10:27:37 - Status: TibState.Standby
10:27:37 - Alarms: AlarmVector.NoAlarm
10:27:37 - Connection status: False TXclient_alive: True
10:27:37 - Status: TibState.Standby
10:27:37 - Alarms: AlarmVector.NoAlarm
10:27:37 - Connection status: False TXclient_alive: True
10:27:38 - Status: TibState.Armed
10:27:38 - Alarms: AlarmVector.NoAlarm
10:27:38 - Connection status: True TXclient_alive: True
10:27:41 - Starting TIB triggers...
10:27:41 - Enabling trigger
10:27:41 - Status: TibState.Running
10:27:41 - Alarms: AlarmVector.ReadError
10:27:41 - Connection status: True TXclient_alive: True
10:27:46 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
10:27:46 - Alarms: AlarmVector.ReadError
10:27:46 - Temperature: 34.94
10:27:46 - Local camera rate: 0.0 Hz
10:27:46 - Stereo trigger rate: 0.0 Hz
10:27:46 - SPE trigger rate: 0.0 Hz
10:27:46 - Calibration trigger rate: 8806.0 Hz
10:27:46 - Software trigger rate: 0.0 Hz
10:27:46 - Pedestal trigger rate: 100.0 Hz
10:27:46 - Collected trigger rate: 8838.0 Hz
10:27:46 - Busy rate: 8838.0 Hz
10:27:46 - Camera trigger rate: 0.0 Hz
10:27:48 - Checking for high voltage locked pixels...
10:27:50 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
10:27:50 - Alarms: AlarmVector.ReadError
10:27:50 - Temperature: 35.00
10:27:50 - Local camera rate: 0.0 Hz
10:27:50 - Stereo trigger rate: 0.0 Hz
10:27:50 - SPE trigger rate: 0.0 Hz
10:27:50 - Calibration trigger rate: 8906.0 Hz
10:27:50 - Software trigger rate: 0.0 Hz
10:27:50 - Pedestal trigger rate: 100.0 Hz
10:27:50 - Collected trigger rate: 8945.0 Hz
10:27:50 - Busy rate: 8945.0 Hz
10:27:50 - Camera trigger rate: 0.0 Hz
10:28:18 - Checking for high voltage locked pixels...
10:28:34 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
10:28:34 - Alarms: AlarmVector.ReadError
10:28:34 - Temperature: 35.00
10:28:34 - Local camera rate: 0.0 Hz
10:28:34 - Stereo trigger rate: 0.0 Hz
10:28:34 - SPE trigger rate: 0.0 Hz
10:28:34 - Calibration trigger rate: 8770.0 Hz
10:28:34 - Software trigger rate: 0.0 Hz
10:28:34 - Pedestal trigger rate: 100.0 Hz
10:28:34 - Collected trigger rate: 8779.0 Hz
10:28:34 - Busy rate: 8779.0 Hz
10:28:34 - Camera trigger rate: 0.0 Hz
10:28:39 - Stopping TIB...
10:28:39 - Status: TibState.Running
10:28:39 - Alarms: AlarmVector.ReadError
10:28:39 - Connection status: True TXclient_alive: True
10:28:39 - Disabling trigger
10:28:39 - Disabling PPS
10:28:40 - Status: TibState.PpsStopped
10:28:40 - Alarms: AlarmVector.ReadError
10:28:40 - Connection status: True TXclient_alive: True
10:28:40 - Closing TIB connection to camera server
10:28:43 - Status: TibState.PpsStopped
10:28:43 - Alarms: AlarmVector.ReadError
10:28:43 - Connection status: False TXclient_alive: False
10:28:43 - Run duration: 0:01:01
10:28:43 - Local camera triggers: 0
10:28:43 - Slow control triggers: 0
10:28:43 - Single photo-electron triggers: 0
10:28:43 - Calibration triggers: 537953
10:28:43 - Software triggers from UCTS: 0
10:28:43 - Pedestal triggers: 6038
10:28:43 - Collected input triggers: 523360
10:28:43 - Busy triggers: 523358
10:28:43 - Camera event triggers sent to clusters: 2
10:28:48 - Checking for high voltage locked pixels...
10:28:51 - Calling method FSM.gotoReady in object FSM
10:28:59 - Stopping NMC
10:28:59 - Found 0 PPS errors.
10:29:18 - Checking for high voltage locked pixels...
10:29:48 - Checking for high voltage locked pixels...