16:52:13 - Updating FEB temperature widget...
16:52:16 - Updating voltage widget...
16:52:51 - Updating L0 scaler widget...
16:52:53 - Updating L1 scaler widget...
16:53:14 - Checking UCTS clock...
16:53:15 - UCTS and control PC clocks differ by 0.2 seconds
16:53:15 - Configuring UCTS
16:53:15 - Configuring TIB...
16:53:15 - Setting TIB forced mode to False
16:53:15 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:53:15 - Status: TibState.RunStopped
16:53:15 - Alarms: AlarmVector.NoAlarm
16:53:15 - Connection status: False TXclient_alive: False
16:53:15 - Disabling PPS
16:53:17 - Status: TibState.PpsStopped
16:53:17 - Alarms: AlarmVector.NoAlarm
16:53:17 - Connection status: False TXclient_alive: False
16:53:17 - Entering set_external_delay
16:53:17 - Setting ExternalDelayLocal to 0.000 ns
16:53:17 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:53:17 - Entering set_external_delay
16:53:17 - Setting ExternalDelayCalibration to 65.000 ns
16:53:17 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:53:17 - Entering set_external_delay
16:53:17 - Setting ExternalDelaySphe to 150.000 ns
16:53:17 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:53:17 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
16:53:17 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:53:17 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:53:17 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:53:17 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:53:17 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:53:17 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:53:17 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:53:17 - Status: TibState.PpsStopped
16:53:18 - Alarms: AlarmVector.NoAlarm
16:53:18 - Connection status: False TXclient_alive: False
16:53:18 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:53:18 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:53:18 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:53:18 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:53:18 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:53:18 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:53:18 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:53:18 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:53:18 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:53:18 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:53:26 - Connecting TIB to camera server at 10.10.4.12:222
16:53:26 - Starting TIB...
16:53:26 - Status: TibState.PpsStopped
16:53:26 - Alarms: AlarmVector.NoAlarm
16:53:26 - Connection status: False TXclient_alive: False
16:53:26 - Resetting run
16:53:26 - Wait for UCTS external trigger before enabling trigger...
16:53:26 - Status: TibState.Standby
16:53:26 - Alarms: AlarmVector.NoAlarm
16:53:26 - Connection status: False TXclient_alive: True
16:53:26 - Status: TibState.Standby
16:53:26 - Alarms: AlarmVector.NoAlarm
16:53:26 - Connection status: False TXclient_alive: True
16:53:27 - Status: TibState.Armed
16:53:27 - Alarms: AlarmVector.NoAlarm
16:53:27 - Connection status: True TXclient_alive: True
16:54:02 - Module 83 is connected to channel 13 of DTC slot 19
16:54:06 - Starting task "Powering modules..."
16:54:06 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 13 --power_on' on Digital Trigger Crate at 10.10.4.57
16:54:08 - Finished task "Powering modules..."
16:54:15 - Starting task "Powering modules..."
16:54:15 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
16:54:17 - Finished task "Powering modules..."
16:54:17 - Module 84 is connected to channel 12 of DTC slot 19
16:54:20 - Starting task "Powering modules..."
16:54:20 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_on' on Digital Trigger Crate at 10.10.4.57
16:54:22 - Finished task "Powering modules..."
16:54:24 - Module 85 is connected to channel 15 of DTC slot 19
16:54:26 - Starting task "Powering modules..."
16:54:26 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_on' on Digital Trigger Crate at 10.10.4.57
16:54:28 - Finished task "Powering modules..."
16:54:33 - Scanning interface enp2s0 for non configured modules...
16:54:34 - Found 2 MAC address(es)
16:54:48 - Starting task "Configure modules"
16:54:48 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
16:54:48 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
16:54:48 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
16:54:48 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
16:54:48 - Configuring modules with configuration /data/config/2020/20201130/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy15.NMC.xml
16:54:48 - Switching off high voltages in configuration
16:54:51 - Successfully configured 2 module(s)
16:54:52 - All front-end boards are programmed with firmware 61201127
16:54:52 - All backplanes are programmed with firmware 15
16:54:52 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:54:53 - Found 0 PPS errors.
16:54:53 - Finished task "Configure modules"
16:54:57 - Starting task "Switch HVPA voltage state"
16:54:57 - Setting HVPA current limit to 12489.75 uA
16:54:58 - Setting HVPA ramp speed to 25 V/s
16:54:58 - Switching HVPA to state Nominal
16:55:05 - Setting HVPA current limits...
16:55:06 - Finished task "Switch HVPA voltage state"
16:55:12 - Updating FEB temperature widget...
16:55:14 - Updating voltage widget...
16:55:18 - High voltage locked channels will be checked every 30 s
16:55:24 - Checking status of calibration box...
16:55:25 - Calibration box is configured with 1 leds at a frequency of 1.0 Hz and a voltage of 15.98 V
16:55:49 - Checking for high voltage locked pixels...
16:55:54 - Starting task "Check high voltages"
16:55:54 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:55:54 - Actual voltage is between 989.42 V and 1167.54 V.
16:55:54 - Low voltages range between 300.00 V and 300.00 V. 
16:55:55 - Reference voltages range between 989.87 V and 1168.35 V. 
16:55:55 - Maximum difference between expected and actual voltages is 0.52 V
16:55:55 - Maximum of current limits is 4840.96 uA
16:55:56 - Checking status of HVPA module in 2 drawer(s)...
16:55:56 - Checking status of HVPA channels in 2 drawer(s)...
16:55:56 - HV is stabilized in all channels.
16:55:56 - Checking reference and low voltages against /data/config/2020/20201130/config_tower_2modules_FEBv6_pingpong_newDacl_DelayBusy15.NMC.xml
16:55:56 - Done
16:55:56 - Finished task "Check high voltages"
16:56:18 - Starting NMC
16:56:18 - Clearing PPS error counters
16:56:19 - Checking for high voltage locked pixels...
16:56:49 - Checking for high voltage locked pixels...
16:57:17 - Starting TIB triggers...
16:57:17 - Enabling trigger
16:57:17 - Status: TibState.Running
16:57:17 - Alarms: AlarmVector.NoAlarm
16:57:17 - Connection status: True TXclient_alive: True
16:57:19 - Checking for high voltage locked pixels...
16:57:20 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
16:57:20 - Alarms: AlarmVector.NoAlarm
16:57:20 - Temperature: 33.94
16:57:20 - Local camera rate: 0.0 Hz
16:57:20 - Stereo trigger rate: 0.0 Hz
16:57:20 - SPE trigger rate: 0.0 Hz
16:57:20 - Calibration trigger rate: 8050.0 Hz
16:57:20 - Software trigger rate: 0.0 Hz
16:57:20 - Pedestal trigger rate: 100.0 Hz
16:57:20 - Collected trigger rate: 8108.0 Hz
16:57:20 - Busy rate: 50.0 Hz
16:57:20 - Camera trigger rate: 8058.0 Hz
16:57:49 - Checking for high voltage locked pixels...
16:58:19 - Checking for high voltage locked pixels...
16:58:49 - Checking for high voltage locked pixels...
16:59:19 - Checking for high voltage locked pixels...
16:59:49 - Checking for high voltage locked pixels...
17:00:19 - Checking for high voltage locked pixels...
17:00:49 - Checking for high voltage locked pixels...
17:01:19 - Checking for high voltage locked pixels...
17:01:49 - Checking for high voltage locked pixels...
17:02:19 - Checking for high voltage locked pixels...
17:02:49 - Checking for high voltage locked pixels...
17:03:19 - Checking for high voltage locked pixels...
17:03:49 - Checking for high voltage locked pixels...
17:04:19 - Checking for high voltage locked pixels...
17:04:49 - Checking for high voltage locked pixels...
17:05:19 - Checking for high voltage locked pixels...
17:05:49 - Checking for high voltage locked pixels...
17:06:19 - Checking for high voltage locked pixels...
17:06:49 - Checking for high voltage locked pixels...
17:06:52 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
17:06:52 - Alarms: AlarmVector.NoAlarm
17:06:52 - Temperature: 34.38
17:06:52 - Local camera rate: 0.0 Hz
17:06:52 - Stereo trigger rate: 0.0 Hz
17:06:52 - SPE trigger rate: 0.0 Hz
17:06:52 - Calibration trigger rate: 8203.0 Hz
17:06:52 - Software trigger rate: 0.0 Hz
17:06:52 - Pedestal trigger rate: 100.0 Hz
17:06:52 - Collected trigger rate: 8246.0 Hz
17:06:52 - Busy rate: 53.0 Hz
17:06:52 - Camera trigger rate: 8193.0 Hz
17:07:19 - Checking for high voltage locked pixels...
17:07:49 - Checking for high voltage locked pixels...
17:08:19 - Checking for high voltage locked pixels...
17:08:49 - Checking for high voltage locked pixels...
17:08:51 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
17:08:51 - Alarms: AlarmVector.ReadError
17:08:51 - Temperature: 34.44
17:08:51 - Local camera rate: 0.0 Hz
17:08:51 - Stereo trigger rate: 0.0 Hz
17:08:51 - SPE trigger rate: 0.0 Hz
17:08:51 - Calibration trigger rate: 8041.0 Hz
17:08:51 - Software trigger rate: 0.0 Hz
17:08:51 - Pedestal trigger rate: 100.0 Hz
17:08:51 - Collected trigger rate: 8086.0 Hz
17:08:51 - Busy rate: 8086.0 Hz
17:08:51 - Camera trigger rate: 0.0 Hz
17:08:59 - Stopping TIB...
17:08:59 - Status: TibState.Running
17:08:59 - Alarms: AlarmVector.ReadError
17:08:59 - Connection status: True TXclient_alive: True
17:08:59 - Disabling trigger
17:08:59 - Disabling PPS
17:09:00 - Status: TibState.PpsStopped
17:09:00 - Alarms: AlarmVector.ReadError
17:09:00 - Connection status: True TXclient_alive: True
17:09:00 - Closing TIB connection to camera server
17:09:01 - Status: TibState.PpsStopped
17:09:01 - Alarms: AlarmVector.ReadError
17:09:01 - Connection status: False TXclient_alive: False
17:09:01 - Run duration: 0:15:32
17:09:01 - Local camera triggers: 0
17:09:01 - Slow control triggers: 0
17:09:01 - Single photo-electron triggers: 0
17:09:01 - Calibration triggers: 7595708
17:09:01 - Software triggers from UCTS: 0
17:09:01 - Pedestal triggers: 93130
17:09:01 - Collected input triggers: 5752687
17:09:01 - Busy triggers: 194489
17:09:01 - Camera event triggers sent to clusters: 5558198
17:09:19 - Checking for high voltage locked pixels...
17:09:49 - Checking for high voltage locked pixels...
17:10:19 - Checking for high voltage locked pixels...
17:10:49 - Checking for high voltage locked pixels...
17:10:54 - Calling method FSM.gotoReady in object FSM
17:10:56 - Stopping NMC
17:10:56 - Found 0 PPS errors.
17:11:19 - Checking for high voltage locked pixels...