16:24:30 - Starting task "Powering modules..."
16:24:30 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_on' on Digital Trigger Crate at 10.10.4.57
16:24:32 - Finished task "Powering modules..."
16:24:34 - Scanning interface enp2s0 for non configured modules...
16:24:38 - Found 1 MAC address(es)
16:24:40 - ECC is in state EccState.Ready with status EccStatus.NoError
16:24:40 - Average temperature: 20.1 deg C
16:24:40 - Air temperature (T1-T6 and T9-T10): 20.1, 1255.0, 1254.0, -838.0, -838.0, -838.0, 1254.0, 1253.0 deg C
16:24:40 - Air differential pressure: 0.0 Pa
16:24:40 - Water temperature (T11-T12): -838.0, 1254.0 deg C
16:24:40 - Back doors are closed.
16:24:40 - Shutter is in state PartiallyOpen (error 0)
16:24:40 - Light sensors: [1.68, 2.0, 2.3, 2.57] V
16:24:40 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:24:40 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:24:40 - 24 V power supply no. 1 is enabled with a current of 1.490 A.
16:25:31 - Starting task "Configure modules"
16:25:31 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
16:25:31 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
16:25:31 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
16:25:31 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
16:25:31 - Configuring modules with configuration /data/config/2020/20201126/config_tower_2modules_FEBv6_pingpong_Dacl.NMC.xml
16:25:31 - Switching off high voltages in configuration
16:25:34 - Successfully configured 2 module(s)
16:25:35 - All front-end boards are programmed with firmware 61201117
16:25:35 - All backplanes are programmed with firmware 15
16:25:36 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:25:36 - Found 0 PPS errors.
16:25:36 - Finished task "Configure modules"
16:25:40 - Starting NMC
16:25:40 - Clearing PPS error counters
16:25:57 - Resetting TIB...
16:26:04 - Configuring calibration box...
16:26:04 - Configuring calibration box with leds=0x40 voltage=15.98 frequency=300.0/300 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
16:26:08 - Checking UCTS clock...
16:26:08 - UCTS clock is late by 20 seconds!
16:26:08 - Configuring UCTS
16:26:08 - Configuring TIB...
16:26:08 - Setting TIB forced mode to False
16:26:08 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:26:08 - Status: TibState.RunStopped
16:26:08 - Alarms: AlarmVector.NoAlarm
16:26:08 - Connection status: False TXclient_alive: False
16:26:08 - Disabling PPS
16:26:10 - Status: TibState.PpsStopped
16:26:10 - Alarms: AlarmVector.NoAlarm
16:26:10 - Connection status: False TXclient_alive: False
16:26:10 - Entering set_external_delay
16:26:10 - Setting ExternalDelayLocal to 0.000 ns
16:26:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:26:11 - Entering set_external_delay
16:26:11 - Setting ExternalDelayCalibration to 65.000 ns
16:26:11 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:26:11 - Entering set_external_delay
16:26:11 - Setting ExternalDelaySphe to 150.000 ns
16:26:11 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:26:11 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
16:26:11 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:26:11 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:26:11 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:26:11 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:26:11 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:26:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:26:11 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:26:12 - Status: TibState.PpsStopped
16:26:12 - Alarms: AlarmVector.NoAlarm
16:26:12 - Connection status: False TXclient_alive: False
16:26:12 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:26:12 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:26:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:26:12 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:26:12 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:26:12 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:26:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:26:12 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:26:12 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:26:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:26:14 - Connecting TIB to camera server at 10.10.4.12:222
16:26:14 - Starting TIB...
16:26:15 - Status: TibState.PpsStopped
16:26:15 - Alarms: AlarmVector.NoAlarm
16:26:15 - Connection status: False TXclient_alive: True
16:26:15 - Resetting run
16:26:15 - Wait for UCTS external trigger before enabling trigger...
16:26:15 - Status: TibState.Standby
16:26:15 - Alarms: AlarmVector.NoAlarm
16:26:15 - Connection status: False TXclient_alive: True
16:26:15 - Status: TibState.Standby
16:26:15 - Alarms: AlarmVector.NoAlarm
16:26:15 - Connection status: False TXclient_alive: True
16:26:16 - Status: TibState.Armed
16:26:16 - Alarms: AlarmVector.NoAlarm
16:26:16 - Connection status: True TXclient_alive: True
16:26:25 - Starting TIB triggers...
16:26:25 - Enabling trigger
16:26:25 - Status: TibState.Running
16:26:25 - Alarms: AlarmVector.NoAlarm
16:26:25 - Connection status: True TXclient_alive: True
16:26:27 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
16:26:27 - Alarms: AlarmVector.NoAlarm
16:26:27 - Temperature: 35.06
16:26:27 - Local camera rate: 0.0 Hz
16:26:27 - Stereo trigger rate: 0.0 Hz
16:26:27 - SPE trigger rate: 0.0 Hz
16:26:27 - Calibration trigger rate: 9388.0 Hz
16:26:28 - Software trigger rate: 0.0 Hz
16:26:28 - Pedestal trigger rate: 1000.0 Hz
16:26:28 - Collected trigger rate: 9315.0 Hz
16:26:28 - Busy rate: 38.0 Hz
16:26:28 - Camera trigger rate: 9277.0 Hz
16:27:33 - Stopping TIB...
16:27:33 - Status: TibState.Running
16:27:33 - Alarms: AlarmVector.NoAlarm
16:27:33 - Connection status: True TXclient_alive: True
16:27:33 - Disabling trigger
16:27:33 - Disabling PPS
16:27:35 - Status: TibState.PpsStopped
16:27:35 - Alarms: AlarmVector.NoAlarm
16:27:35 - Connection status: True TXclient_alive: True
16:27:35 - Closing TIB connection to camera server
16:27:36 - Status: TibState.PpsStopped
16:27:36 - Alarms: AlarmVector.NoAlarm
16:27:36 - Connection status: False TXclient_alive: False
16:27:36 - Run duration: 0:01:18
16:27:36 - Local camera triggers: 0
16:27:36 - Slow control triggers: 0
16:27:36 - Single photo-electron triggers: 0
16:27:36 - Calibration triggers: 731259
16:27:36 - Software triggers from UCTS: 0
16:27:36 - Pedestal triggers: 77706
16:27:36 - Collected input triggers: 641344
16:27:36 - Busy triggers: 2687
16:27:36 - Camera event triggers sent to clusters: 638657
16:27:39 - Calling method FSM.gotoReady in object FSM
16:27:42 - Stopping NMC
16:27:42 - Found 0 PPS errors.