10:27:25 - Checking for high voltage locked pixels...
10:27:26 - Resetting NMC
10:27:30 - Starting task "Configure modules"
10:27:30 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/utils/branches/v5.5.1-40061 
10:27:30 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libNectarCam/branches/v5.5.1-40061 
10:27:30 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/libQNectarCam/branches/v5.5.1-40061 
10:27:30 - Version of NMC: svn+ssh://svn.in2p3.fr/cta/MST/NectarCAM/qNectarcamModuleController/branches/v5.5.1-40061
10:27:30 - Configuring modules with configuration /data/config/2020/20201027/config_tower_2modules_FEBv6_pingpong_Dacl.NMC.xml
10:27:30 - Switching off high voltages in configuration
10:27:34 - Successfully configured 2 module(s)
10:27:34 - All front-end boards are programmed with firmware F61D2010
10:27:35 - All backplanes are programmed with firmware 15
10:27:35 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
10:27:35 - Found 0 PPS errors.
10:27:35 - Finished task "Configure modules"
10:27:36 - Starting task "Switch HVPA voltage state"
10:27:36 - Setting HVPA current limit to 12489.75 uA
10:27:37 - Setting HVPA ramp speed to 25 V/s
10:27:37 - Switching HVPA to state Nominal
10:27:44 - Setting HVPA current limits...
10:27:45 - Finished task "Switch HVPA voltage state"
10:27:48 - Starting task "Check high voltages"
10:27:48 - Found 2 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:27:48 - Actual voltage is between 989.42 V and 1168.15 V.
10:27:48 - Low voltages range between 300.00 V and 300.00 V. 
10:27:49 - Reference voltages range between 989.87 V and 1168.35 V. 
10:27:49 - Maximum difference between expected and actual voltages is 0.52 V
10:27:50 - Maximum of current limits is 4840.96 uA
10:27:50 - Checking status of HVPA module in 2 drawer(s)...
10:27:50 - Checking status of HVPA channels in 2 drawer(s)...
10:27:50 - HV is stabilized in all channels.
10:27:50 - Checking reference and low voltages against /data/config/2020/20201027/config_tower_2modules_FEBv6_pingpong_Dacl.NMC.xml
10:27:50 - Done
10:27:50 - Finished task "Check high voltages"
10:27:52 - Starting NMC
10:27:52 - Clearing PPS error counters
10:27:55 - Checking for high voltage locked pixels...
10:27:55 - Calling method FSM.gotoReady in object FSM
10:28:02 - Calling method FSM.gotoObserving in object FSM
10:28:07 - Checking UCTS clock...
10:28:07 - UCTS clock is late by 28 seconds!
10:28:07 - Configuring UCTS
10:28:07 - Configuring TIB...
10:28:07 - Setting TIB forced mode to False
10:28:07 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:28:07 - Status: TibState.PpsStopped
10:28:07 - Alarms: AlarmVector.NoAlarm
10:28:07 - Connection status: False TXclient_alive: False
10:28:07 - Entering set_external_delay
10:28:07 - Setting ExternalDelayLocal to 0.000 ns
10:28:07 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:28:08 - Entering set_external_delay
10:28:08 - Setting ExternalDelayCalibration to 65.000 ns
10:28:08 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:28:08 - Entering set_external_delay
10:28:08 - Setting ExternalDelaySphe to 150.000 ns
10:28:08 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:28:08 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
10:28:08 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:28:08 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:28:08 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:28:08 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:28:08 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:28:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:28:08 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:28:08 - Status: TibState.PpsStopped
10:28:08 - Alarms: AlarmVector.NoAlarm
10:28:08 - Connection status: False TXclient_alive: False
10:28:08 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:28:08 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:28:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:28:08 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:28:08 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:28:08 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:28:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:28:08 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:28:08 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:28:08 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:28:10 - Connecting TIB to camera server at 10.10.4.12:222
10:28:10 - Starting TIB...
10:28:10 - Status: TibState.PpsStopped
10:28:10 - Alarms: AlarmVector.NoAlarm
10:28:10 - Connection status: False TXclient_alive: True
10:28:10 - Resetting run
10:28:10 - Wait for UCTS external trigger before enabling trigger...
10:28:10 - Status: TibState.Standby
10:28:10 - Alarms: AlarmVector.NoAlarm
10:28:10 - Connection status: False TXclient_alive: True
10:28:10 - Status: TibState.Standby
10:28:10 - Alarms: AlarmVector.NoAlarm
10:28:10 - Connection status: False TXclient_alive: True
10:28:11 - Status: TibState.Armed
10:28:11 - Alarms: AlarmVector.NoAlarm
10:28:11 - Connection status: True TXclient_alive: True
10:28:13 - Starting TIB triggers...
10:28:13 - Enabling trigger
10:28:13 - Status: TibState.Running
10:28:13 - Alarms: AlarmVector.NoAlarm
10:28:13 - Connection status: True TXclient_alive: True
10:28:25 - Checking for high voltage locked pixels...
10:28:26 - Stopping TIB...
10:28:26 - Status: TibState.Running
10:28:26 - Alarms: AlarmVector.NoAlarm
10:28:26 - Connection status: True TXclient_alive: True
10:28:26 - Disabling trigger
10:28:26 - Disabling PPS
10:28:27 - Status: TibState.PpsStopped
10:28:27 - Alarms: AlarmVector.NoAlarm
10:28:27 - Connection status: True TXclient_alive: True
10:28:27 - Closing TIB connection to camera server
10:28:28 - Status: TibState.PpsStopped
10:28:28 - Alarms: AlarmVector.NoAlarm
10:28:28 - Connection status: False TXclient_alive: False
10:28:28 - Run duration: 0:00:14
10:28:28 - Local camera triggers: 0
10:28:28 - Slow control triggers: 0
10:28:28 - Single photo-electron triggers: 0
10:28:28 - Calibration triggers: 0
10:28:28 - Software triggers from UCTS: 0
10:28:28 - Pedestal triggers: 138609
10:28:28 - Collected input triggers: 124601
10:28:28 - Busy triggers: 0
10:28:28 - Camera event triggers sent to clusters: 124601