13:16:54 - Starting task "Configure modules"
13:16:54 - Setting L0 thresholds to 15.0 p.e. per pixel using L0 slopes and offsets in /data/luts/l0_threshold_slope_and_offset_feb_20191203.h5
13:16:54 - Configuring modules with configuration /data/config/2020/20200706/config_2020-07-06_13-16-54.NMC.xml
13:16:54 - Switching off high voltages in configuration
13:16:58 - Successfully configured 53 module(s)
13:16:59 - All front-end boards are programmed with firmware F55D2001
13:17:00 - All backplanes are programmed with firmware 15
13:17:08 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
13:17:09 - Found 0 PPS errors.
13:17:10 - Finished task "Configure modules"
13:17:13 - Starting task "Switch HVPA voltage state"
13:17:13 - Setting HVPA current limit to 12489.75 uA
13:17:17 - Checking for high voltage locked pixels...
13:17:33 - Setting HVPA ramp speed to 25 V/s
13:17:36 - Switching HVPA to state Nominal
13:17:45 - Setting HVPA current limits...
13:17:47 - Checking for high voltage locked pixels...
13:18:13 - Finished task "Switch HVPA voltage state"
13:18:17 - Checking for high voltage locked pixels...
13:18:22 - Starting task "Check high voltages"
13:18:23 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:18:33 - Actual voltage is between 945.50 V and 1166.93 V.
13:18:34 - Low voltages range between 300.00 V and 300.00 V. 
13:18:47 - Checking for high voltage locked pixels...
13:18:48 - Reference voltages range between 945.26 V and 1167.15 V. 
13:18:59 - Maximum difference between expected and actual voltages is 0.78 V
13:19:06 - Maximum of current limits is 5647.07 uA
13:19:06 - Checking status of HVPA module in 53 drawer(s)...
13:19:07 - Checking status of HVPA channels in 53 drawer(s)...
13:19:11 - HV is stabilized in all channels.
13:19:11 - Checking reference and low voltages against /data/config/2020/20200701/config_tower_53modules.NMC.xml
13:19:17 - Checking for high voltage locked pixels...
13:19:19 - Done
13:19:19 - Finished task "Check high voltages"
13:19:47 - Checking for high voltage locked pixels...
13:20:17 - Checking for high voltage locked pixels...
13:20:47 - Checking for high voltage locked pixels...
13:21:17 - Checking for high voltage locked pixels...
13:21:47 - Checking for high voltage locked pixels...
13:22:17 - Checking for high voltage locked pixels...
13:22:47 - Checking for high voltage locked pixels...
13:23:17 - Checking for high voltage locked pixels...
13:23:47 - Checking for high voltage locked pixels...
13:24:17 - Checking for high voltage locked pixels...
13:24:47 - Checking for high voltage locked pixels...
13:25:17 - Checking for high voltage locked pixels...
13:25:47 - Checking for high voltage locked pixels...
13:26:17 - Checking for high voltage locked pixels...
13:26:47 - Checking for high voltage locked pixels...
13:26:59 - Calling method FSM.gotoReady in object FSM
13:27:17 - Checking for high voltage locked pixels...
13:27:47 - Checking for high voltage locked pixels...
13:28:17 - Checking for high voltage locked pixels...
13:28:24 - Calling method FSM.gotoObserving in object FSM
13:28:47 - Checking for high voltage locked pixels...
13:29:17 - Checking for high voltage locked pixels...
13:29:19 - Starting task "Set DTC trigger masks"
13:29:19 - Configuring DTC trigger masks for 53 configured module(s)
13:29:19 - Setting DTC slot 1 trigger mask to 0xf7ee
13:29:23 - Setting DTC slot 5 trigger mask to 0xfdb6
13:29:26 - Setting DTC slot 6 trigger mask to 0x0028
13:29:30 - Setting DTC slot 9 trigger mask to 0x0000
13:29:33 - Setting DTC slot 13 trigger mask to 0xdff8
13:29:37 - Setting DTC slot 14 trigger mask to 0x00d0
13:29:40 - Setting DTC slot 15 trigger mask to 0x0600
13:29:44 - Setting DTC slot 19 trigger mask to 0xb786
13:29:47 - Checking for high voltage locked pixels...
13:29:48 - Finished task "Set DTC trigger masks"
13:29:51 - Starting NMC
13:29:51 - Clearing PPS error counters
13:30:09 - Checking status of calibration box...
13:30:10 - Calibration box is configured with 1 leds at a frequency of 1000.0 Hz and a voltage of 8.99 V
13:30:17 - Checking for high voltage locked pixels...
13:30:47 - Checking for high voltage locked pixels...
13:30:49 - Configuring calibration box...
13:30:49 - Configuring calibration box with leds=0x40 voltage=9.00 frequency=4000.0/1 central_current=0.0 duration=0 width=1 lemo_out=False fiber1_out=False fiber2_out=False lemo_in=False enabled=False
13:30:50 - Starting flashes...
13:30:54 - Checking status of calibration box...
13:30:55 - Calibration box is configured with 1 leds at a frequency of 1000.0 Hz and a voltage of 15.99 V
13:31:15 - Configuring calibration box...
13:31:15 - Configuring calibration box with leds=0x40 voltage=12.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
13:31:17 - Checking for high voltage locked pixels...
13:31:22 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
13:31:22 - Alarms: AlarmVector.NoAlarm
13:31:22 - Temperature: 38.81
13:31:22 - Local camera rate: 8746.0 Hz
13:31:22 - Stereo trigger rate: 0.0 Hz
13:31:22 - SPE trigger rate: 0.0 Hz
13:31:22 - Calibration trigger rate: 4839.0 Hz
13:31:22 - Software trigger rate: 0.0 Hz
13:31:22 - Pedestal trigger rate: 999.0 Hz
13:31:22 - Collected trigger rate: 0.0 Hz
13:31:22 - Busy rate: 0.0 Hz
13:31:22 - Camera trigger rate: 0.0 Hz
13:31:30 - Status: TibState.PpsStopped ConnectionStatus: False TXclient_alive: False
13:31:30 - Alarms: AlarmVector.NoAlarm
13:31:30 - Temperature: 38.81
13:31:30 - Local camera rate: 8697.0 Hz
13:31:30 - Stereo trigger rate: 0.0 Hz
13:31:30 - SPE trigger rate: 0.0 Hz
13:31:30 - Calibration trigger rate: 4786.0 Hz
13:31:30 - Software trigger rate: 0.0 Hz
13:31:30 - Pedestal trigger rate: 1000.0 Hz
13:31:30 - Collected trigger rate: 0.0 Hz
13:31:30 - Busy rate: 0.0 Hz
13:31:30 - Camera trigger rate: 0.0 Hz
13:31:37 - Checking UCTS clock...
13:31:37 - UCTS clock is late by 8 seconds!
13:31:38 - Configuring UCTS
13:31:38 - Configuring TIB...
13:31:38 - Setting TIB forced mode to False
13:31:38 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:31:38 - Status: TibState.PpsStopped
13:31:38 - Alarms: AlarmVector.NoAlarm
13:31:38 - Connection status: False TXclient_alive: False
13:31:38 - Entering set_external_delay
13:31:38 - Setting ExternalDelayLocal to 0.000 ns
13:31:38 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:31:38 - Entering set_external_delay
13:31:38 - Setting ExternalDelayCalibration to 65.000 ns
13:31:38 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:31:38 - Entering set_external_delay
13:31:38 - Setting ExternalDelaySphe to 150.000 ns
13:31:38 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:31:38 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
13:31:38 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:31:38 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:31:38 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:31:38 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:31:38 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:31:38 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:31:38 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:31:38 - Status: TibState.PpsStopped
13:31:38 - Alarms: AlarmVector.NoAlarm
13:31:38 - Connection status: False TXclient_alive: False
13:31:38 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:31:38 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:31:38 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:31:38 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:31:38 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:31:39 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:31:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:31:39 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:31:39 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:31:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:31:43 - Connecting TIB to camera server at 10.10.4.12:222
13:31:44 - Starting TIB...
13:31:44 - Status: TibState.PpsStopped
13:31:44 - Alarms: AlarmVector.NoAlarm
13:31:44 - Connection status: False TXclient_alive: False
13:31:44 - Resetting run
13:31:44 - Wait for UCTS external trigger before enabling trigger...
13:31:44 - Status: TibState.Standby
13:31:44 - Alarms: AlarmVector.NoAlarm
13:31:44 - Connection status: False TXclient_alive: False
13:31:44 - Status: TibState.Standby
13:31:44 - Alarms: AlarmVector.NoAlarm
13:31:44 - Connection status: False TXclient_alive: False
13:31:45 - Status: TibState.Armed
13:31:45 - Alarms: AlarmVector.NoAlarm
13:31:45 - Connection status: True TXclient_alive: True
13:31:47 - Checking for high voltage locked pixels...
13:32:17 - Checking for high voltage locked pixels...
13:32:26 - Starting TIB triggers...
13:32:26 - Enabling trigger
13:32:26 - Status: TibState.Running
13:32:26 - Alarms: AlarmVector.NoAlarm
13:32:26 - Connection status: True TXclient_alive: True
13:32:32 - Stopping TIB...
13:32:32 - Status: TibState.Running
13:32:32 - Alarms: AlarmVector.NoAlarm
13:32:32 - Connection status: True TXclient_alive: True
13:32:32 - Disabling trigger
13:32:32 - Disabling PPS
13:32:33 - Status: TibState.PpsStopped
13:32:33 - Alarms: AlarmVector.NoAlarm
13:32:33 - Connection status: True TXclient_alive: True
13:32:33 - Closing TIB connection to camera server
13:32:37 - Status: TibState.PpsStopped
13:32:37 - Alarms: AlarmVector.NoAlarm
13:32:37 - Connection status: False TXclient_alive: False
13:32:37 - Run duration: 0:00:47
13:32:37 - Local camera triggers: 410654
13:32:37 - Slow control triggers: 0
13:32:37 - Single photo-electron triggers: 0
13:32:37 - Calibration triggers: 227214
13:32:37 - Software triggers from UCTS: 0
13:32:37 - Pedestal triggers: 4695
13:32:37 - Collected input triggers: 57372
13:32:37 - Busy triggers: 2541
13:32:37 - Camera event triggers sent to clusters: 54831
13:32:47 - Checking for high voltage locked pixels...
13:32:50 - Stopping NMC
13:32:51 - Found 0 PPS errors.