11:40:21 - ECC is in state EccState.Ready with status EccStatus.NoError
11:40:21 - Average temperature: 21.7 deg C
11:40:21 - Air temperature (T1-T6 and T9-T10): 21.7, -838.0, -838.0, -838.0, 1254.0, 1254.0, 1254.0, 1253.0 deg C
11:40:21 - Air differential pressure: 0.0 Pa
11:40:21 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
11:40:21 - Back doors are closed.
11:40:21 - Shutter is in state PartiallyOpen (error 0)
11:40:21 - Light sensors: [2.3, 2.75, 3.13, 3.44] V
11:40:21 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
11:40:21 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
11:40:21 - 24 V power supply no. 1 is enabled with a current of 39.000 A.
11:40:27 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
11:40:28 - Found 0 PPS errors.
12:58:49 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
12:58:49 - Found 0 PPS errors.
13:58:50 - Starting task "Switch HVPA voltage state"
13:58:50 - Setting HVPA current limit to 12489.75 uA
13:58:55 - High voltage locked channels will be checked every 30 s
13:59:07 - Setting HVPA ramp speed to 25 V/s
13:59:09 - Switching HVPA to state Nominal
13:59:18 - Setting HVPA current limits...
13:59:25 - Checking for high voltage locked pixels...
13:59:26 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
13:59:27 - Unlocking 1 channel(s)...
13:59:27 - Resetting HVPA channel 6 of drawer 81...
13:59:36 - Stopping flashes...
13:59:41 - Finished task "Switch HVPA voltage state"
13:59:43 - Configuring calibration box...
13:59:43 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=999.0/3 central_current=0.0 duration=0 width=1 lemo_out=False fiber1_out=False fiber2_out=False lemo_in=False enabled=False
13:59:45 - Starting flashes...
13:59:55 - Checking for high voltage locked pixels...
13:59:56 - Module 146 has 1 pixel(s) locked (HVPA status of 0x7d)!
13:59:57 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
13:59:57 - Unlocking 2 channel(s)...
13:59:57 - Resetting HVPA channel 1 of drawer 146...
13:59:57 - Resetting HVPA channel 3 of drawer 163...
14:00:26 - Checking for high voltage locked pixels...
14:00:50 - Starting task "Check high voltages"
14:00:51 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:00:55 - Checking for high voltage locked pixels...
14:00:59 - Actual voltage is between 944.89 V and 1167.54 V.
14:01:00 - Low voltages range between 300.00 V and 300.00 V. 
14:01:09 - Reference voltages range between 945.26 V and 1167.15 V. 
14:01:18 - Maximum difference between expected and actual voltages is 0.68 V
14:01:23 - Maximum of current limits is 5647.07 uA
14:01:23 - Checking status of HVPA module in 53 drawer(s)...
14:01:23 - Checking status of HVPA channels in 53 drawer(s)...
14:01:25 - Checking for high voltage locked pixels...
14:01:28 - HV is stabilized in all channels.
14:01:28 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
14:01:33 - Done
14:01:33 - Finished task "Check high voltages"
14:01:55 - Checking for high voltage locked pixels...
14:02:00 - Starting task "Set L0 trigger thresholds"
14:02:00 - Setting L0 thresholds to 15.0 p.e. using /local/home/cta_test_bench/data/2019/20191203/l0_threshold_slope_and_offset_feb.h5
14:02:06 - NumExpr defaulting to 4 threads.
14:02:42 - Checking for high voltage locked pixels...
14:02:55 - Checking for high voltage locked pixels...
14:02:57 - Setting L0 thresholds to 15.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20191203/l0_threshold_slope_and_offset_feb.h5
14:02:58 - Thresholds saved in configuration file /local/home/cta_test_bench/config/2020/20200625/config_2020-06-25_14-02-57.NMC.xml
14:02:58 - Finished task "Set L0 trigger thresholds"
14:03:25 - Checking for high voltage locked pixels...
14:03:33 - Configuring calibration box...
14:03:33 - Configuring calibration box with leds=0x40 voltage=9.00 frequency=999.0/3 central_current=0.0 duration=0 width=1 lemo_out=False fiber1_out=False fiber2_out=False lemo_in=False enabled=False
14:03:34 - Starting flashes...
14:03:55 - Checking for high voltage locked pixels...
14:04:17 - Starting NMC
14:04:17 - Clearing PPS error counters
14:04:24 - Calling method FSM.gotoObserving in object FSM
14:04:25 - Checking for high voltage locked pixels...
14:04:54 - Checking UCTS clock...
14:04:54 - UCTS and control PC clocks differ by 2.384758 seconds
14:04:54 - Configuring UCTS
14:04:54 - Configuring TIB...
14:04:54 - Setting TIB forced mode to False
14:04:54 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:04:54 - Status: TibState.RunStopped
14:04:54 - Alarms: AlarmVector.NoAlarm
14:04:54 - Connection status: False TXclient_alive: False
14:04:54 - Disabling PPS
14:04:56 - Status: TibState.PpsStopped
14:04:56 - Alarms: AlarmVector.NoAlarm
14:04:56 - Connection status: False TXclient_alive: False
14:04:56 - Entering set_external_delay
14:04:56 - Setting ExternalDelayLocal to 0.000 ns
14:04:56 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:04:57 - Entering set_external_delay
14:04:57 - Setting ExternalDelayCalibration to 65.000 ns
14:04:57 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:04:57 - Entering set_external_delay
14:04:57 - Setting ExternalDelaySphe to 150.000 ns
14:04:57 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:04:57 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
14:04:57 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:04:58 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:04:58 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:04:58 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:04:58 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:04:58 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:04:58 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:04:58 - Status: TibState.PpsStopped
14:04:58 - Alarms: AlarmVector.NoAlarm
14:04:58 - Connection status: False TXclient_alive: False
14:04:58 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:04:58 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:04:58 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:04:58 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:04:58 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:04:58 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:04:58 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:04:58 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:04:58 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:04:58 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:04:59 - Checking for high voltage locked pixels...
14:05:13 - Connecting TIB to camera server at 10.10.4.12:222
14:05:13 - Starting TIB...
14:05:13 - Status: TibState.PpsStopped
14:05:13 - Alarms: AlarmVector.NoAlarm
14:05:13 - Connection status: False TXclient_alive: False
14:05:13 - Resetting run
14:05:13 - Wait for UCTS external trigger before enabling trigger...
14:05:13 - Status: TibState.Standby
14:05:13 - Alarms: AlarmVector.NoAlarm
14:05:13 - Connection status: False TXclient_alive: False
14:05:13 - Status: TibState.Standby
14:05:13 - Alarms: AlarmVector.NoAlarm
14:05:13 - Connection status: False TXclient_alive: True
14:05:14 - Status: TibState.Armed
14:05:14 - Alarms: AlarmVector.NoAlarm
14:05:14 - Connection status: True TXclient_alive: True
14:05:17 - Starting TIB triggers...
14:05:17 - Enabling trigger
14:05:17 - Status: TibState.Running
14:05:17 - Alarms: AlarmVector.NoAlarm
14:05:17 - Connection status: True TXclient_alive: True
14:05:25 - Checking for high voltage locked pixels...
14:05:39 - Stopping TIB...
14:05:39 - Status: TibState.Running
14:05:39 - Alarms: AlarmVector.ReadError
14:05:39 - Connection status: True TXclient_alive: True
14:05:39 - Disabling trigger
14:05:39 - Disabling PPS
14:05:41 - Status: TibState.PpsStopped
14:05:41 - Alarms: AlarmVector.ReadError
14:05:41 - Connection status: True TXclient_alive: True
14:05:41 - Closing TIB connection to camera server
14:05:44 - Status: TibState.PpsStopped
14:05:44 - Alarms: AlarmVector.ReadError
14:05:44 - Connection status: False TXclient_alive: False
14:05:44 - Run duration: 0:00:25
14:05:44 - Local camera triggers: 1
14:05:44 - Slow control triggers: 0
14:05:44 - Single photo-electron triggers: 0
14:05:44 - Calibration triggers: 0
14:05:44 - Software triggers from UCTS: 0
14:05:44 - Pedestal triggers: 2448
14:05:44 - Collected input triggers: 9702
14:05:44 - Busy triggers: 11
14:05:44 - Camera event triggers sent to clusters: 9691
14:05:47 - Calling method FSM.gotoReady in object FSM
14:05:50 - Stopping NMC
14:05:51 - Found 0 PPS errors.