12:37:31 - Stopping flashes...
12:37:38 - Resetting NMC
12:37:41 - Starting task "Configure modules"
12:37:42 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
12:37:42 - Switching off high voltages in configuration
12:37:46 - Successfully configured 53 module(s)
12:37:47 - All front-end boards are programmed with firmware F55D2001
12:37:48 - All backplanes are programmed with firmware 15
12:37:53 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
12:37:54 - Found 0 PPS errors.
12:37:54 - Finished task "Configure modules"
12:37:56 - Stopping NMC
12:37:57 - Found 0 PPS errors.
12:38:00 - Starting NMC
12:38:00 - Clearing PPS error counters
12:38:06 - Starting task "Switch HVPA voltage state"
12:38:06 - Setting HVPA current limit to 12489.75 uA
12:38:13 - Calling method FSM.gotoObserving in object FSM
12:38:24 - Setting HVPA ramp speed to 25 V/s
12:38:26 - Switching HVPA to state Nominal
12:38:28 - Checking UCTS clock...
12:38:29 - UCTS and control PC clocks differ by 1.088337 seconds
12:38:29 - Configuring UCTS
12:38:29 - Configuring TIB...
12:38:29 - Setting TIB forced mode to False
12:38:29 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
12:38:29 - Status: TibState.PpsStopped
12:38:29 - Alarms: AlarmVector.ReadError
12:38:29 - Connection status: False TXclient_alive: False
12:38:29 - Entering set_external_delay
12:38:29 - Setting ExternalDelayLocal to 0.000 ns
12:38:29 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
12:38:29 - Entering set_external_delay
12:38:29 - Setting ExternalDelayCalibration to 65.000 ns
12:38:29 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
12:38:29 - Entering set_external_delay
12:38:29 - Setting ExternalDelaySphe to 150.000 ns
12:38:29 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
12:38:29 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
12:38:29 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
12:38:29 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
12:38:29 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
12:38:29 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
12:38:29 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
12:38:29 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
12:38:29 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
12:38:29 - Status: TibState.PpsStopped
12:38:29 - Alarms: AlarmVector.ReadError
12:38:29 - Connection status: False TXclient_alive: False
12:38:29 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
12:38:30 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
12:38:30 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:38:30 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
12:38:30 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
12:38:30 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
12:38:30 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:38:30 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
12:38:30 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
12:38:30 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:38:35 - Setting HVPA current limits...
12:38:57 - Finished task "Switch HVPA voltage state"
12:39:10 - High voltage locked channels will be checked every 30 s
12:39:40 - Checking for high voltage locked pixels...
12:39:40 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
12:39:41 - Module 146 has 1 pixel(s) locked (HVPA status of 0x7d)!
12:39:41 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
12:39:41 - Unlocking 3 channel(s)...
12:39:41 - Resetting HVPA channel 6 of drawer 81...
12:39:41 - Resetting HVPA channel 1 of drawer 146...
12:39:41 - Resetting HVPA channel 3 of drawer 163...
12:40:09 - Checking for high voltage locked pixels...
12:40:39 - Checking for high voltage locked pixels...
12:41:09 - Checking for high voltage locked pixels...
12:41:15 - Starting task "Check high voltages"
12:41:16 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
12:41:24 - Actual voltage is between 945.50 V and 1166.93 V.
12:41:25 - Low voltages range between 300.00 V and 300.00 V. 
12:41:34 - Reference voltages range between 945.26 V and 1167.15 V. 
12:41:39 - Checking for high voltage locked pixels...
12:41:43 - Maximum difference between expected and actual voltages is 0.67 V
12:41:47 - Maximum of current limits is 5647.07 uA
12:41:47 - Checking status of HVPA module in 53 drawer(s)...
12:41:48 - Checking status of HVPA channels in 53 drawer(s)...
12:41:52 - HV is stabilized in all channels.
12:41:52 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
12:41:57 - Done
12:41:58 - Finished task "Check high voltages"
12:42:05 - Stopping NMC
12:42:05 - Found 0 PPS errors.
12:42:06 - Starting NMC
12:42:06 - Clearing PPS error counters
12:42:09 - Checking for high voltage locked pixels...
12:42:11 - Connecting TIB to camera server at 10.10.4.12:222
12:42:11 - Starting TIB...
12:42:11 - Status: TibState.PpsStopped
12:42:11 - Alarms: AlarmVector.ReadError
12:42:11 - Connection status: False TXclient_alive: True
12:42:11 - Resetting run
12:42:11 - Wait for UCTS external trigger before enabling trigger...
12:42:11 - Status: TibState.Standby
12:42:11 - Alarms: AlarmVector.NoAlarm
12:42:11 - Connection status: False TXclient_alive: True
12:42:11 - Status: TibState.Standby
12:42:11 - Alarms: AlarmVector.NoAlarm
12:42:11 - Connection status: False TXclient_alive: True
12:42:12 - Status: TibState.Armed
12:42:12 - Alarms: AlarmVector.NoAlarm
12:42:12 - Connection status: True TXclient_alive: True
12:42:16 - Configuring calibration box...
12:42:16 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
12:42:17 - Starting flashes...
12:42:22 - Starting TIB triggers...
12:42:22 - Enabling trigger
12:42:22 - Status: TibState.Running
12:42:22 - Alarms: AlarmVector.NoAlarm
12:42:22 - Connection status: True TXclient_alive: True
12:42:32 - Stopping TIB...
12:42:32 - Status: TibState.Running
12:42:32 - Alarms: AlarmVector.ReadError
12:42:32 - Connection status: True TXclient_alive: True
12:42:32 - Disabling trigger
12:42:32 - Disabling PPS
12:42:33 - Status: TibState.PpsStopped
12:42:33 - Alarms: AlarmVector.ReadError
12:42:33 - Connection status: True TXclient_alive: True
12:42:33 - Closing TIB connection to camera server
12:42:34 - Status: TibState.PpsStopped
12:42:34 - Alarms: AlarmVector.ReadError
12:42:34 - Connection status: False TXclient_alive: False
12:42:34 - Run duration: 0:00:19
12:42:34 - Local camera triggers: 0
12:42:34 - Slow control triggers: 0
12:42:34 - Single photo-electron triggers: 0
12:42:34 - Calibration triggers: 13700
12:42:34 - Software triggers from UCTS: 0
12:42:34 - Pedestal triggers: 1888
12:42:34 - Collected input triggers: 10986
12:42:34 - Busy triggers: 0
12:42:34 - Camera event triggers sent to clusters: 10986
12:42:37 - Calling method FSM.gotoReady in object FSM
12:42:39 - Checking for high voltage locked pixels...
12:42:41 - Stopping NMC
12:42:42 - Found 0 PPS errors.