13:52:20 - Resetting NMC
13:52:26 - Starting task "Configure modules"
13:52:27 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
13:52:27 - Switching off high voltages in configuration
13:52:33 - Successfully configured 53 module(s)
13:52:34 - All front-end boards are programmed with firmware F55D2001
13:52:36 - All backplanes are programmed with firmware 15
13:52:40 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
13:52:41 - Found 0 PPS errors.
13:52:41 - Finished task "Configure modules"
13:52:49 - Starting task "Switch HVPA voltage state"
13:52:49 - Setting HVPA current limit to 12489.75 uA
13:52:51 - High voltage locked channels will be checked every 30 s
13:52:55 - Starting NMC
13:52:55 - Clearing PPS error counters
13:53:07 - Setting HVPA ramp speed to 25 V/s
13:53:09 - Switching HVPA to state Nominal
13:53:18 - Setting HVPA current limits...
13:53:22 - Checking for high voltage locked pixels...
13:53:22 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
13:53:23 - Unlocking 1 channel(s)...
13:53:23 - Resetting HVPA channel 6 of drawer 81...
13:53:41 - Finished task "Switch HVPA voltage state"
13:53:52 - Checking for high voltage locked pixels...
13:53:52 - Module 146 has 1 pixel(s) locked (HVPA status of 0x7d)!
13:53:53 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
13:54:10 - Unlocking 2 channel(s)...
13:54:10 - Resetting HVPA channel 1 of drawer 146...
13:54:11 - Resetting HVPA channel 3 of drawer 163...
13:54:22 - Checking for high voltage locked pixels...
13:54:36 - Starting task "Check high voltages"
13:54:36 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:54:45 - Actual voltage is between 945.50 V and 1167.54 V.
13:54:45 - Low voltages range between 300.00 V and 300.00 V. 
13:54:52 - Checking for high voltage locked pixels...
13:54:54 - Reference voltages range between 945.26 V and 1167.15 V. 
13:55:03 - Maximum difference between expected and actual voltages is 0.71 V
13:55:08 - Maximum of current limits is 5647.07 uA
13:55:08 - Checking status of HVPA module in 53 drawer(s)...
13:55:09 - Checking status of HVPA channels in 53 drawer(s)...
13:55:13 - HV is stabilized in all channels.
13:55:13 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
13:55:18 - Done
13:55:18 - Finished task "Check high voltages"
13:55:21 - Checking for high voltage locked pixels...
13:55:34 - Calling method FSM.gotoObserving in object FSM
13:55:52 - Checking for high voltage locked pixels...
13:56:07 - Configuring calibration box...
13:56:08 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
13:56:15 - Configuring UCTS
13:56:16 - Configuring TIB...
13:56:16 - Setting TIB forced mode to False
13:56:16 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:56:16 - Status: TibState.PpsStopped
13:56:16 - Alarms: AlarmVector.ReadError
13:56:16 - Connection status: False TXclient_alive: False
13:56:16 - Entering set_external_delay
13:56:16 - Setting ExternalDelayLocal to 0.000 ns
13:56:16 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:56:16 - Entering set_external_delay
13:56:16 - Setting ExternalDelayCalibration to 65.000 ns
13:56:16 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:56:16 - Entering set_external_delay
13:56:16 - Setting ExternalDelaySphe to 150.000 ns
13:56:16 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:56:16 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
13:56:16 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:56:16 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:56:16 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:56:16 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:56:17 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:56:17 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:56:17 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:56:17 - Status: TibState.PpsStopped
13:56:17 - Alarms: AlarmVector.ReadError
13:56:17 - Connection status: False TXclient_alive: False
13:56:17 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:56:17 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:56:17 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:56:17 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:56:17 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:56:17 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:56:17 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:56:17 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:56:17 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:56:17 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:56:21 - Connecting TIB to camera server at 10.10.4.12:222
13:56:21 - Starting TIB...
13:56:21 - Status: TibState.PpsStopped
13:56:21 - Alarms: AlarmVector.ReadError
13:56:21 - Connection status: False TXclient_alive: False
13:56:21 - Resetting run
13:56:21 - Wait for UCTS external trigger before enabling trigger...
13:56:21 - Status: TibState.Standby
13:56:21 - Alarms: AlarmVector.NoAlarm
13:56:21 - Connection status: False TXclient_alive: True
13:56:21 - Status: TibState.Standby
13:56:21 - Alarms: AlarmVector.NoAlarm
13:56:21 - Connection status: False TXclient_alive: True
13:56:22 - Status: TibState.Armed
13:56:22 - Alarms: AlarmVector.NoAlarm
13:56:22 - Connection status: True TXclient_alive: True
13:56:22 - Checking for high voltage locked pixels...
13:56:24 - Starting TIB triggers...
13:56:24 - Enabling trigger
13:56:24 - Status: TibState.Running
13:56:24 - Alarms: AlarmVector.NoAlarm
13:56:25 - Connection status: True TXclient_alive: True
13:56:27 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
13:56:27 - Alarms: AlarmVector.NoAlarm
13:56:27 - Temperature: 34.94
13:56:27 - Local camera rate: 0.0 Hz
13:56:27 - Stereo trigger rate: 0.0 Hz
13:56:27 - SPE trigger rate: 0.0 Hz
13:56:27 - Calibration trigger rate: 7461.0 Hz
13:56:27 - Software trigger rate: 0.0 Hz
13:56:27 - Pedestal trigger rate: 100.0 Hz
13:56:27 - Collected trigger rate: 7502.0 Hz
13:56:27 - Busy rate: 430.0 Hz
13:56:27 - Camera trigger rate: 7072.0 Hz
13:56:39 - Stopping TIB...
13:56:39 - Status: TibState.Running
13:56:39 - Alarms: AlarmVector.NoAlarm
13:56:39 - Connection status: True TXclient_alive: True
13:56:39 - Disabling trigger
13:56:39 - Disabling PPS
13:56:40 - Status: TibState.PpsStopped
13:56:40 - Alarms: AlarmVector.NoAlarm
13:56:40 - Connection status: True TXclient_alive: True
13:56:40 - Closing TIB connection to camera server
13:56:46 - Status: TibState.PpsStopped
13:56:46 - Alarms: AlarmVector.NoAlarm
13:56:46 - Connection status: False TXclient_alive: False
13:56:46 - Run duration: 0:00:17
13:56:46 - Local camera triggers: 0
13:56:46 - Slow control triggers: 0
13:56:46 - Single photo-electron triggers: 0
13:56:46 - Calibration triggers: 119930
13:56:46 - Software triggers from UCTS: 0
13:56:46 - Pedestal triggers: 1617
13:56:46 - Collected input triggers: 106186
13:56:46 - Busy triggers: 5499
13:56:46 - Camera event triggers sent to clusters: 100687
13:56:51 - Checking for high voltage locked pixels...
13:57:03 - Calling method FSM.gotoReady in object FSM
13:57:21 - Checking for high voltage locked pixels...