17:15:16 - ECC is in state EccState.Safe with status EccStatus.NoError
17:15:16 - Average temperature: 19.0 deg C
17:15:16 - Air temperature (T1-T6 and T9-T10): 19.0, -838.0, 1254.0, -838.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
17:15:16 - Air differential pressure: 0.0 Pa
17:15:16 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
17:15:16 - Back doors are closed.
17:15:16 - Shutter is in state PartiallyOpen (error 0)
17:15:16 - Light sensors: [2.32, 2.57, 2.76, 3.14] V
17:15:16 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
17:15:16 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
17:15:16 - 24 V power supply no. 1 is disabled with a current of 6.360 A.
09:27:56 - ECC is in state EccState.Safe with status EccStatus.NoError
09:27:56 - Average temperature: 17.6 deg C
09:27:56 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, 1254.0, 1254.0, -838.0, 1254.0, -838.0, -838.0 deg C
09:27:56 - Air differential pressure: 0.0 Pa
09:27:56 - Water temperature (T11-T12): 1253.0, -838.0 deg C
09:27:56 - Back doors are closed.
09:27:56 - Shutter is in state PartiallyOpen (error 0)
09:27:56 - Light sensors: [2.21, 2.65, 3.07, 3.43] V
09:27:56 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:27:56 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:27:56 - 24 V power supply no. 1 is disabled with a current of 6.410 A.
09:27:57 - Starting task "Prepare ECC"
09:27:57 - Preparing ECC...
09:27:57 - Setting ECC temperature range for Ready state to [16.000000, 36.000000]
09:27:58 - Setting ECC mode to EccTransition.Ready
09:27:58 - Received ECC state change notification: EccState.Safe
09:28:04 - Received ECC state change notification: EccState.Ready
09:28:05 - Received ECC state change notification: EccState.Ready
09:28:06 - Setting power supply box SPE relay to True
09:28:06 - Finished task "Prepare ECC"
09:28:10 - Starting task "Powering modules..."
09:28:10 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:16 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:22 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:26 - ECC is in state EccState.Ready with status EccStatus.NoError
09:28:26 - Average temperature: 17.6 deg C
09:28:26 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, -838.0, -838.0, 1254.0, -838.0, -838.0 deg C
09:28:27 - Air differential pressure: 0.0 Pa
09:28:27 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:28:27 - Back doors are closed.
09:28:27 - Shutter is in state PartiallyOpen (error 0)
09:28:27 - Light sensors: [2.23, 2.66, 3.1, 3.46] V
09:28:27 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:28:27 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:28:27 - 24 V power supply no. 1 is enabled with a current of 20.200 A.
09:28:28 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:33 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:39 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:45 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:51 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:28:56 - Finished task "Powering modules..."
09:29:01 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:01 - Average temperature: 17.6 deg C
09:29:01 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0, 1253.0 deg C
09:29:01 - Air differential pressure: 0.0 Pa
09:29:01 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:01 - Back doors are closed.
09:29:01 - Shutter is in state PartiallyOpen (error 0)
09:29:01 - Light sensors: [2.3, 2.72, 3.13, 3.48] V
09:29:01 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:01 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:01 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:03 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:03 - Average temperature: 17.6 deg C
09:29:03 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0, 1253.0 deg C
09:29:03 - Air differential pressure: 0.0 Pa
09:29:03 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:03 - Back doors are closed.
09:29:03 - Shutter is in state PartiallyOpen (error 0)
09:29:03 - Light sensors: [2.29, 2.72, 3.13, 3.48] V
09:29:03 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:03 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:03 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:05 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:05 - Average temperature: 17.6 deg C
09:29:05 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, 1254.0, -838.0, 1254.0, 1254.0, 1254.0, 1253.0 deg C
09:29:05 - Air differential pressure: 0.0 Pa
09:29:05 - Water temperature (T11-T12): -838.0, -838.0 deg C
09:29:05 - Back doors are closed.
09:29:05 - Shutter is in state PartiallyOpen (error 0)
09:29:05 - Light sensors: [2.31, 2.72, 3.14, 3.48] V
09:29:05 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:05 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:05 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:06 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:06 - Average temperature: 17.6 deg C
09:29:06 - Air temperature (T1-T6 and T9-T10): 17.6, -838.0, 1254.0, 1254.0, -838.0, -838.0, 1254.0, 1253.0 deg C
09:29:06 - Air differential pressure: 0.0 Pa
09:29:06 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:06 - Back doors are closed.
09:29:06 - Shutter is in state PartiallyOpen (error 0)
09:29:06 - Light sensors: [2.31, 2.72, 3.14, 3.48] V
09:29:06 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:06 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:06 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:07 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:07 - Average temperature: 17.6 deg C
09:29:07 - Air temperature (T1-T6 and T9-T10): 17.6, -838.0, 1254.0, 1254.0, -838.0, -838.0, 1254.0, 1253.0 deg C
09:29:07 - Air differential pressure: 0.0 Pa
09:29:07 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:07 - Back doors are closed.
09:29:07 - Shutter is in state PartiallyOpen (error 0)
09:29:07 - Light sensors: [2.31, 2.72, 3.14, 3.48] V
09:29:07 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:07 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:07 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:08 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:08 - Average temperature: 17.6 deg C
09:29:08 - Air temperature (T1-T6 and T9-T10): 17.6, -838.0, 1254.0, 1254.0, -838.0, 1254.0, 1254.0, 1253.0 deg C
09:29:08 - Air differential pressure: 0.0 Pa
09:29:08 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:08 - Back doors are closed.
09:29:08 - Shutter is in state PartiallyOpen (error 0)
09:29:08 - Light sensors: [2.31, 2.72, 3.14, 3.48] V
09:29:08 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:08 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:09 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:10 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:10 - Average temperature: 17.6 deg C
09:29:10 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, -838.0, -838.0, -838.0, 1253.0 deg C
09:29:10 - Air differential pressure: 0.0 Pa
09:29:10 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:10 - Back doors are closed.
09:29:10 - Shutter is in state PartiallyOpen (error 0)
09:29:10 - Light sensors: [2.29, 2.72, 3.13, 3.48] V
09:29:10 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:10 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:10 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:11 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:11 - Average temperature: 17.6 deg C
09:29:11 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, -838.0, -838.0, -838.0, 1253.0 deg C
09:29:11 - Air differential pressure: 0.0 Pa
09:29:11 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:11 - Back doors are closed.
09:29:11 - Shutter is in state PartiallyOpen (error 0)
09:29:11 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:11 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:11 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:11 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:12 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:12 - Average temperature: 17.6 deg C
09:29:12 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, -838.0, 1254.0, 1254.0, -838.0 deg C
09:29:12 - Air differential pressure: 0.0 Pa
09:29:12 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:12 - Back doors are closed.
09:29:12 - Shutter is in state PartiallyOpen (error 0)
09:29:12 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:12 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:12 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:12 - 24 V power supply no. 1 is enabled with a current of 41.200 A.
09:29:13 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:13 - Average temperature: 17.6 deg C
09:29:13 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, -838.0, 1254.0, 1254.0, -838.0 deg C
09:29:13 - Air differential pressure: 0.0 Pa
09:29:13 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:13 - Back doors are closed.
09:29:13 - Shutter is in state PartiallyOpen (error 0)
09:29:13 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:13 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:13 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:13 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:14 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:14 - Average temperature: 17.6 deg C
09:29:14 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
09:29:14 - Air differential pressure: 0.0 Pa
09:29:14 - Water temperature (T11-T12): 1253.0, -838.0 deg C
09:29:14 - Back doors are closed.
09:29:14 - Shutter is in state PartiallyOpen (error 0)
09:29:14 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:14 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:14 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:14 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:15 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:15 - Average temperature: 17.6 deg C
09:29:15 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
09:29:15 - Air differential pressure: 0.0 Pa
09:29:15 - Water temperature (T11-T12): 1253.0, -838.0 deg C
09:29:15 - Back doors are closed.
09:29:15 - Shutter is in state PartiallyOpen (error 0)
09:29:15 - Light sensors: [2.3, 2.73, 3.15, 3.49] V
09:29:15 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:15 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:15 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:17 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:17 - Average temperature: 17.6 deg C
09:29:17 - Air temperature (T1-T6 and T9-T10): 17.6, -838.0, 1254.0, 1254.0, -838.0, 1254.0, 1254.0, 1253.0 deg C
09:29:17 - Air differential pressure: 0.0 Pa
09:29:17 - Water temperature (T11-T12): -838.0, -838.0 deg C
09:29:17 - Back doors are closed.
09:29:17 - Shutter is in state PartiallyOpen (error 0)
09:29:17 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:17 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:17 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:17 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:21 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:21 - Average temperature: 17.6 deg C
09:29:21 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, -838.0, 1254.0, 1254.0, 1253.0 deg C
09:29:21 - Air differential pressure: 0.0 Pa
09:29:21 - Water temperature (T11-T12): 1253.0, -838.0 deg C
09:29:21 - Back doors are closed.
09:29:21 - Shutter is in state PartiallyOpen (error 0)
09:29:21 - Light sensors: [2.3, 2.73, 3.14, 3.49] V
09:29:21 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:21 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:21 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:23 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:23 - Average temperature: 17.6 deg C
09:29:23 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, -838.0, 1254.0, -838.0, 1254.0, 1253.0 deg C
09:29:23 - Air differential pressure: 0.0 Pa
09:29:23 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:23 - Back doors are closed.
09:29:23 - Shutter is in state PartiallyOpen (error 0)
09:29:23 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:23 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:23 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:23 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:24 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:24 - Average temperature: 17.6 deg C
09:29:24 - Air temperature (T1-T6 and T9-T10): 17.6, -838.0, 1254.0, -838.0, 1254.0, 1254.0, -838.0, 1253.0 deg C
09:29:24 - Air differential pressure: 0.0 Pa
09:29:24 - Water temperature (T11-T12): -838.0, 1254.0 deg C
09:29:24 - Back doors are closed.
09:29:24 - Shutter is in state PartiallyOpen (error 0)
09:29:24 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:29:24 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:24 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:24 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:25 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:25 - Average temperature: 17.6 deg C
09:29:25 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, -838.0, 1254.0, -838.0, 1254.0, 1253.0 deg C
09:29:25 - Air differential pressure: 0.0 Pa
09:29:25 - Water temperature (T11-T12): -838.0, 1254.0 deg C
09:29:25 - Back doors are closed.
09:29:25 - Shutter is in state PartiallyOpen (error 0)
09:29:25 - Light sensors: [2.3, 2.73, 3.14, 3.49] V
09:29:25 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:25 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:25 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:27 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:27 - Average temperature: 17.6 deg C
09:29:27 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, -838.0, 1254.0, -838.0, 1254.0, 1253.0 deg C
09:29:27 - Air differential pressure: 0.0 Pa
09:29:27 - Water temperature (T11-T12): -838.0, 1254.0 deg C
09:29:27 - Back doors are closed.
09:29:27 - Shutter is in state PartiallyOpen (error 0)
09:29:27 - Light sensors: [2.28, 2.72, 3.13, 3.48] V
09:29:27 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:27 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:27 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:28 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:28 - Average temperature: 17.6 deg C
09:29:28 - Air temperature (T1-T6 and T9-T10): 17.6, 1255.0, -838.0, 1254.0, 1254.0, -838.0, -838.0, 1253.0 deg C
09:29:28 - Air differential pressure: 0.0 Pa
09:29:28 - Water temperature (T11-T12): -838.0, -838.0 deg C
09:29:28 - Back doors are closed.
09:29:28 - Shutter is in state PartiallyOpen (error 0)
09:29:28 - Light sensors: [2.28, 2.72, 3.13, 3.48] V
09:29:28 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:28 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:28 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:29 - ECC is in state EccState.Ready with status EccStatus.NoError
09:29:29 - Average temperature: 17.6 deg C
09:29:29 - Air temperature (T1-T6 and T9-T10): 17.6, -838.0, 1254.0, 1254.0, 1254.0, -838.0, 1254.0, 1253.0 deg C
09:29:29 - Air differential pressure: 0.0 Pa
09:29:29 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
09:29:29 - Back doors are closed.
09:29:29 - Shutter is in state PartiallyOpen (error 0)
09:29:29 - Light sensors: [2.31, 2.73, 3.14, 3.49] V
09:29:29 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:29:29 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:29:29 - 24 V power supply no. 1 is enabled with a current of 41.300 A.
09:29:32 - Scanning interface p4p1 for non configured modules...
09:29:39 - Found 0 MAC address(es)
09:29:42 - Scanning interface p4p1 for non configured modules...
09:29:49 - Found 0 MAC address(es)
09:29:52 - Status: TibState.RunStopped
09:29:52 - Alarms: AlarmVector.NoAlarm
09:29:52 - Connection status: False TXclient_alive: False
09:29:52 - External delays: Local=3825.000 ns, Calibration=3825.000 ns, Sphe=3825.000 ns
09:29:52 - Trigger mask: 0x51 = TriggerMask.SlowControl|Software|Mono
09:29:52 - Input mask: 0x7
09:29:52 - Disable BUSY: False
09:29:52 - Extra BUSY Delay: 0.0
09:29:52 - Temperature: 21.44
09:30:05 - ECC is in state EccState.Ready with status EccStatus.NoError
09:30:05 - Average temperature: 17.7 deg C
09:30:05 - Air temperature (T1-T6 and T9-T10): 17.7, -838.0, -838.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
09:30:05 - Air differential pressure: 0.0 Pa
09:30:05 - Water temperature (T11-T12): -838.0, 1254.0 deg C
09:30:05 - Back doors are closed.
09:30:05 - Shutter is in state PartiallyOpen (error 0)
09:30:05 - Light sensors: [2.29, 2.72, 3.14, 3.48] V
09:30:05 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:30:05 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:30:05 - 24 V power supply no. 1 is enabled with a current of 45.300 A.
09:30:09 - Scanning interface p4p1 for non configured modules...
09:30:09 - Found 61 MAC address(es)
09:30:16 - Starting task "Configure modules"
09:30:16 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
09:30:16 - Switching off high voltages in configuration
09:30:21 - Successfully configured 53 module(s)
09:30:22 - All front-end boards are programmed with firmware F55D2001
09:30:23 - All backplanes are programmed with firmware 15
09:30:28 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
09:30:29 - Found 0 PPS errors.
09:30:29 - Finished task "Configure modules"
09:30:51 - Starting task "Power off channels not corresponding to a configured module"
09:30:51 - Powering off all but 53 DTC channel(s)
09:30:52 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
09:30:54 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
09:30:56 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
09:30:58 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
09:30:59 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:01 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:03 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:05 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:06 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:08 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:10 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:12 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:13 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:15 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:17 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:19 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:20 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:22 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:24 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:26 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:29 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:33 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:36 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:38 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:41 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:43 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:45 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:52 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:54 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:57 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
09:31:59 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:01 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:03 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:04 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:06 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:08 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:10 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:11 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:13 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:15 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:17 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:20 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:22 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:24 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:25 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:29 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:32 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:34 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:36 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:38 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:39 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:41 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:43 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:45 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:46 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
09:32:50 - Finished task "Power off channels not corresponding to a configured module"
10:37:54 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
10:37:55 - Found 0 PPS errors.
10:57:00 - Starting task "Switch HVPA voltage state"
10:57:00 - Setting HVPA current limit to 12489.75 uA
10:57:06 - High voltage locked channels will be checked every 30 s
10:57:18 - Calling method FSM.gotoObserving in object FSM
10:57:19 - Setting HVPA ramp speed to 25 V/s
10:57:21 - Switching HVPA to state Nominal
10:57:30 - Setting HVPA current limits...
10:57:36 - Checking for high voltage locked pixels...
10:57:36 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
10:57:37 - Unlocking 1 channel(s)...
10:57:38 - Resetting HVPA channel 6 of drawer 81...
10:57:53 - Finished task "Switch HVPA voltage state"
10:58:05 - Checking for high voltage locked pixels...
10:58:06 - Module 146 has 1 pixel(s) locked (HVPA status of 0x7d)!
10:58:07 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
10:58:07 - Unlocking 2 channel(s)...
10:58:07 - Resetting HVPA channel 1 of drawer 146...
10:58:07 - Resetting HVPA channel 3 of drawer 163...
10:58:35 - Checking for high voltage locked pixels...
10:58:37 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
10:58:37 - Unlocking 1 channel(s)...
10:58:37 - Resetting HVPA channel 3 of drawer 163...
10:59:06 - Checking for high voltage locked pixels...
10:59:17 - Starting task "Check high voltages"
10:59:17 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:59:26 - Actual voltage is between 945.50 V and 1167.54 V.
10:59:26 - Low voltages range between 300.00 V and 300.00 V. 
10:59:30 - Starting NMC
10:59:30 - Clearing PPS error counters
10:59:35 - Checking for high voltage locked pixels...
10:59:36 - Reference voltages range between 945.26 V and 1167.15 V. 
10:59:45 - Maximum difference between expected and actual voltages is 7.68 V
10:59:49 - Maximum of current limits is 5647.07 uA
10:59:49 - Checking status of HVPA module in 53 drawer(s)...
10:59:50 - Checking status of HVPA channels in 53 drawer(s)...
10:59:54 - HV is stabilized in all channels.
10:59:54 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
10:59:59 - Done
11:00:00 - Finished task "Check high voltages"
11:00:00 - Starting task "Check high voltages"
11:00:01 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
11:00:05 - Checking for high voltage locked pixels...
11:00:09 - Actual voltage is between 945.50 V and 1167.54 V.
11:00:10 - Low voltages range between 300.00 V and 300.00 V. 
11:00:19 - Reference voltages range between 945.26 V and 1167.15 V. 
11:00:28 - Maximum difference between expected and actual voltages is 1.07 V
11:00:32 - Maximum of current limits is 5647.07 uA
11:00:32 - Checking status of HVPA module in 53 drawer(s)...
11:00:33 - Checking status of HVPA channels in 53 drawer(s)...
11:00:35 - Checking for high voltage locked pixels...
11:00:37 - HV is stabilized in all channels.
11:00:37 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200610/config_tower_53modules.NMC.xml
11:00:42 - Done
11:00:43 - Finished task "Check high voltages"
11:00:47 - Configuring calibration box...
11:00:47 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=True enabled=True
11:00:53 - Configuring UCTS
11:00:53 - Configuring TIB...
11:00:53 - Setting TIB forced mode to False
11:00:53 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:00:53 - Status: TibState.RunStopped
11:00:53 - Alarms: AlarmVector.NoAlarm
11:00:53 - Connection status: False TXclient_alive: False
11:00:53 - Disabling PPS
11:00:55 - Status: TibState.PpsStopped
11:00:55 - Alarms: AlarmVector.NoAlarm
11:00:55 - Connection status: False TXclient_alive: False
11:00:55 - Entering set_external_delay
11:00:55 - Setting ExternalDelayLocal to 0.000 ns
11:00:55 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:00:56 - Entering set_external_delay
11:00:56 - Setting ExternalDelayCalibration to 65.000 ns
11:00:56 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:00:56 - Entering set_external_delay
11:00:56 - Setting ExternalDelaySphe to 150.000 ns
11:00:56 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:00:56 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
11:00:56 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:00:56 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:00:56 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:00:56 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:00:56 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:00:56 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:00:56 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:00:56 - Status: TibState.PpsStopped
11:00:56 - Alarms: AlarmVector.NoAlarm
11:00:56 - Connection status: False TXclient_alive: False
11:00:56 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:00:56 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:00:56 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:00:56 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:00:56 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:00:56 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:00:56 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:00:56 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:00:56 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:00:56 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:00:58 - Connecting TIB to camera server at 10.10.4.12:222
11:00:58 - Starting TIB...
11:00:58 - Status: TibState.PpsStopped
11:00:58 - Alarms: AlarmVector.NoAlarm
11:00:58 - Connection status: False TXclient_alive: False
11:00:58 - Resetting run
11:00:58 - Wait for UCTS external trigger before enabling trigger...
11:00:58 - Status: TibState.Standby
11:00:58 - Alarms: AlarmVector.NoAlarm
11:00:58 - Connection status: False TXclient_alive: False
11:00:58 - Status: TibState.Standby
11:00:58 - Alarms: AlarmVector.NoAlarm
11:00:58 - Connection status: False TXclient_alive: False
11:00:59 - Status: TibState.Armed
11:00:59 - Alarms: AlarmVector.NoAlarm
11:00:59 - Connection status: True TXclient_alive: True
11:01:00 - Starting TIB triggers...
11:01:00 - Enabling trigger
11:01:00 - Status: TibState.Running
11:01:00 - Alarms: AlarmVector.NoAlarm
11:01:00 - Connection status: True TXclient_alive: True
11:01:05 - Checking for high voltage locked pixels...
11:01:23 - Status: TibState.Running ConnectionStatus: True TXclient_alive: True
11:01:23 - Alarms: AlarmVector.ReadError
11:01:23 - Temperature: 32.56
11:01:23 - Local camera rate: 0.0 Hz
11:01:23 - Stereo trigger rate: 0.0 Hz
11:01:23 - SPE trigger rate: 0.0 Hz
11:01:23 - Calibration trigger rate: 5865.0 Hz
11:01:23 - Software trigger rate: 0.0 Hz
11:01:23 - Pedestal trigger rate: 100.0 Hz
11:01:23 - Collected trigger rate: 5901.0 Hz
11:01:23 - Busy rate: 281.0 Hz
11:01:23 - Camera trigger rate: 5620.0 Hz
11:01:27 - Stopping TIB...
11:01:27 - Status: TibState.Running
11:01:27 - Alarms: AlarmVector.ReadError
11:01:27 - Connection status: True TXclient_alive: True
11:01:27 - Disabling trigger
11:01:27 - Disabling PPS
11:01:28 - Status: TibState.PpsStopped
11:01:28 - Alarms: AlarmVector.ReadError
11:01:29 - Connection status: True TXclient_alive: True
11:01:29 - Closing TIB connection to camera server
11:01:36 - Checking for high voltage locked pixels...
11:01:39 - Status: TibState.PpsStopped
11:01:39 - Alarms: AlarmVector.ReadError
11:01:39 - Connection status: False TXclient_alive: False
11:01:39 - Run duration: 0:00:29
11:01:39 - Local camera triggers: 0
11:01:39 - Slow control triggers: 0
11:01:39 - Single photo-electron triggers: 0
11:01:39 - Calibration triggers: 169575
11:01:39 - Software triggers from UCTS: 0
11:01:39 - Pedestal triggers: 2824
11:01:39 - Collected input triggers: 165647
11:01:39 - Busy triggers: 7217
11:01:39 - Camera event triggers sent to clusters: 158430
11:02:06 - Checking for high voltage locked pixels...
11:02:22 - Calling method FSM.gotoReady in object FSM
11:02:35 - Checking for high voltage locked pixels...
11:03:05 - Checking for high voltage locked pixels...