09:27:19 - Stopping NMC
09:27:19 - Found 0 PPS errors.
09:27:22 - Resetting NMC
09:27:24 - Starting task "Configure modules"
09:27:24 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200610/config_tower_2modules.NMC.xml
09:27:24 - Switching off high voltages in configuration
09:27:24 - Checking for high voltage locked pixels...
09:27:27 - Successfully configured 2 module(s)
09:27:28 - All front-end boards are programmed with firmware F55D1907
09:27:28 - All backplanes are programmed with firmware 15
09:27:28 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
09:27:28 - Found PPS errors: 94 in drawer 93
09:27:29 - Finished task "Configure modules"
09:27:44 - Starting task "Switch HVPA voltage state"
09:27:44 - Setting HVPA current limit to 12489.75 uA
09:27:44 - Setting HVPA ramp speed to 25 V/s
09:27:44 - Switching HVPA to state Nominal
09:27:52 - Setting HVPA current limits...
09:27:53 - Finished task "Switch HVPA voltage state"
09:27:54 - Checking for high voltage locked pixels...
09:27:56 - Starting task "Check high voltages"
09:27:56 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
09:27:56 - Actual voltage is between 855.83 V and 1004.06 V.
09:27:56 - Low voltages range between 300.00 V and 300.00 V. 
09:27:56 - Reference voltages range between 970.31 V and 1125.07 V. 
09:27:57 - Maximum difference between expected and actual voltages is 718.70 V
09:27:57 - Maximum of current limits is 4871.16 uA
09:27:57 - Checking status of HVPA module in 2 drawer(s)...
09:27:57 - Checking status of HVPA channels in 2 drawer(s)...
09:27:57 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 14 channel(s)
09:27:57 - Finished task "Check high voltages"
09:28:21 - Calling method FSM.gotoObserving in object FSM
09:28:24 - Checking for high voltage locked pixels...
09:28:34 - Starting task "Check high voltages"
09:28:34 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
09:28:34 - Actual voltage is between 969.90 V and 1124.84 V.
09:28:34 - Low voltages range between 300.00 V and 300.00 V. 
09:28:35 - Reference voltages range between 970.31 V and 1125.07 V. 
09:28:35 - Maximum difference between expected and actual voltages is 824.84 V
09:28:35 - Maximum of current limits is 4871.16 uA
09:28:35 - Checking status of HVPA module in 2 drawer(s)...
09:28:35 - Checking status of HVPA channels in 2 drawer(s)...
09:28:35 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
09:28:36 - Finished task "Check high voltages"
09:28:48 - Starting task "Check high voltages"
09:28:48 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
09:28:49 - Actual voltage is between 969.90 V and 1124.84 V.
09:28:49 - Low voltages range between 300.00 V and 300.00 V. 
09:28:49 - Reference voltages range between 970.31 V and 1125.07 V. 
09:28:49 - Maximum difference between expected and actual voltages is 825.45 V
09:28:49 - Maximum of current limits is 4871.16 uA
09:28:49 - Checking status of HVPA module in 2 drawer(s)...
09:28:50 - Checking status of HVPA channels in 2 drawer(s)...
09:28:50 - HV is stabilized in all channels.
09:28:50 - Finished task "Check high voltages"
09:28:51 - Starting NMC
09:28:51 - Clearing PPS error counters
09:28:54 - Checking for high voltage locked pixels...
09:28:58 - Configuring UCTS
09:28:58 - Configuring TIB...
09:28:58 - Setting TIB forced mode to False
09:28:58 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
09:28:58 - Status: TibState.PpsStopped
09:28:58 - Alarms: AlarmVector.ReadError
09:28:58 - Connection status: False TXclient_alive: False
09:28:58 - Entering set_external_delay
09:28:58 - Setting ExternalDelayLocal to 0.000 ns
09:28:58 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
09:28:59 - Entering set_external_delay
09:28:59 - Setting ExternalDelayCalibration to 65.000 ns
09:28:59 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
09:28:59 - Entering set_external_delay
09:28:59 - Setting ExternalDelaySphe to 150.000 ns
09:28:59 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
09:28:59 - Setting TIB trigger mode to 0x55 = TriggerMask.SlowControl|Software|Calibration|Mono
09:28:59 - Writing 85 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
09:28:59 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
09:28:59 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
09:28:59 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
09:28:59 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
09:28:59 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
09:28:59 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
09:28:59 - Status: TibState.PpsStopped
09:28:59 - Alarms: AlarmVector.ReadError
09:28:59 - Connection status: False TXclient_alive: False
09:28:59 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
09:28:59 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
09:28:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:28:59 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
09:28:59 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
09:28:59 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
09:28:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:28:59 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
09:28:59 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
09:28:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:29:00 - Connecting TIB to camera server at 10.10.4.12:222
09:29:00 - Starting TIB...
09:29:00 - Status: TibState.PpsStopped
09:29:00 - Alarms: AlarmVector.ReadError
09:29:00 - Connection status: False TXclient_alive: False
09:29:00 - Resetting run
09:29:00 - Wait for UCTS external trigger before enabling trigger...
09:29:00 - Status: TibState.Standby
09:29:00 - Alarms: AlarmVector.NoAlarm
09:29:00 - Connection status: False TXclient_alive: True
09:29:00 - Status: TibState.Standby
09:29:00 - Alarms: AlarmVector.NoAlarm
09:29:00 - Connection status: False TXclient_alive: True
09:29:01 - Status: TibState.Armed
09:29:01 - Alarms: AlarmVector.NoAlarm
09:29:01 - Connection status: True TXclient_alive: True
09:29:02 - Starting TIB triggers...
09:29:02 - Enabling trigger
09:29:02 - Status: TibState.Running
09:29:02 - Alarms: AlarmVector.NoAlarm
09:29:02 - Connection status: True TXclient_alive: True
09:29:04 - Configuring calibration box...
09:29:04 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=200 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
09:29:06 - Starting flashes...
09:29:24 - Checking for high voltage locked pixels...
09:29:31 - Stopping TIB...
09:29:31 - Status: TibState.Running
09:29:31 - Alarms: AlarmVector.ReadError
09:29:31 - Connection status: True TXclient_alive: True
09:29:31 - Disabling trigger
09:29:31 - Disabling PPS
09:29:32 - Status: TibState.PpsStopped
09:29:32 - Alarms: AlarmVector.ReadError
09:29:32 - Connection status: True TXclient_alive: True
09:29:32 - Closing TIB connection to camera server
09:29:36 - Status: TibState.PpsStopped
09:29:36 - Alarms: AlarmVector.ReadError
09:29:36 - Connection status: False TXclient_alive: False
09:29:36 - Run duration: 0:00:30
09:29:36 - Local camera triggers: 0
09:29:36 - Slow control triggers: 0
09:29:36 - Single photo-electron triggers: 0
09:29:36 - Calibration triggers: 19921
09:29:36 - Software triggers from UCTS: 0
09:29:36 - Pedestal triggers: 0
09:29:36 - Collected input triggers: 19921
09:29:36 - Busy triggers: 0
09:29:36 - Camera event triggers sent to clusters: 19921
09:29:39 - Calling method FSM.gotoReady in object FSM
09:29:54 - Checking for high voltage locked pixels...
09:30:24 - Checking for high voltage locked pixels...