09:04:18 - Starting task "Configure modules"
09:04:18 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200609/config_tower_2modules_adlershof.NMC.xml
09:04:18 - Switching off high voltages in configuration
09:04:22 - Successfully configured 2 module(s)
09:04:22 - All front-end boards are programmed with firmware F55D1907
09:04:22 - All backplanes are programmed with firmware 15
09:04:22 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
09:04:22 - Found 0 PPS errors.
09:04:23 - Finished task "Configure modules"
09:04:27 - Starting task "Check high voltages"
09:04:27 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
09:04:28 - Actual voltage is between 0.00 V and 3.05 V.
09:04:28 - Low voltages range between 300.00 V and 300.00 V. 
09:04:28 - Reference voltages range between 978.32 V and 1112.69 V. 
09:04:28 - Maximum difference between expected and actual voltages is 300.00 V
09:04:28 - Maximum of current limits is 4871.16 uA
09:04:28 - Checking status of HVPA module in 2 drawer(s)...
09:04:28 - Checking status of HVPA channels in 2 drawer(s)...
09:04:29 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 14 channel(s)
09:04:29 - Finished task "Check high voltages"
09:04:49 - Starting task "Switch HVPA voltage state"
09:04:49 - Setting HVPA current limit to 12489.75 uA
09:04:50 - Setting HVPA ramp speed to 25 V/s
09:04:50 - Switching HVPA to state Nominal
09:04:57 - Setting HVPA current limits...
09:04:58 - Finished task "Switch HVPA voltage state"
09:06:24 - High voltage locked channels will be checked every 30 s
09:06:26 - Starting task "Check high voltages"
09:06:26 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
09:06:26 - Actual voltage is between 977.83 V and 1112.64 V.
09:06:26 - Low voltages range between 300.00 V and 300.00 V. 
09:06:26 - Reference voltages range between 978.32 V and 1112.69 V. 
09:06:26 - Maximum difference between expected and actual voltages is 813.25 V
09:06:27 - Maximum of current limits is 4871.16 uA
09:06:27 - Checking status of HVPA module in 2 drawer(s)...
09:06:27 - Checking status of HVPA channels in 2 drawer(s)...
09:06:27 - HV is stabilized in all channels.
09:06:27 - Finished task "Check high voltages"
09:06:32 - Stopping NMC
09:06:32 - Found PPS errors: 255 in drawer 93
09:06:34 - Starting NMC
09:06:34 - Clearing PPS error counters
09:06:41 - Calling method FSM.gotoStandby in object FSM
09:06:44 - Event builder is in state CameraServerState.Standby and has output 2458 event(s) (2458 complete).
09:06:46 - Calling method FSM.quit in object FSM
09:06:54 - Checking for high voltage locked pixels...
09:07:24 - Checking for high voltage locked pixels...
09:07:54 - Checking for high voltage locked pixels...
09:08:24 - Checking for high voltage locked pixels...
09:08:54 - Checking for high voltage locked pixels...
09:09:24 - Checking for high voltage locked pixels...
09:09:32 - Calling method FSM.gotoReady in object FSM
09:09:46 - Calling method FSM.gotoObserving in object FSM
09:09:54 - Checking for high voltage locked pixels...
09:09:59 - Configuring UCTS
09:09:59 - Configuring TIB...
09:09:59 - Setting TIB forced mode to False
09:09:59 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
09:09:59 - Status: TibState.PpsStopped
09:09:59 - Alarms: AlarmVector.ReadError
09:09:59 - Connection status: False TXclient_alive: False
09:09:59 - Entering set_external_delay
09:09:59 - Setting ExternalDelayLocal to 0.000 ns
09:09:59 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
09:10:00 - Entering set_external_delay
09:10:00 - Setting ExternalDelayCalibration to 65.000 ns
09:10:00 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
09:10:00 - Entering set_external_delay
09:10:00 - Setting ExternalDelaySphe to 150.000 ns
09:10:00 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
09:10:00 - Setting TIB trigger mode to 0x55 = TriggerMask.SlowControl|Software|Calibration|Mono
09:10:00 - Writing 85 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
09:10:00 - Writing 1 to Camera.TIB.InputsEnable.InputMask.InputMask_v
09:10:00 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
09:10:00 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
09:10:00 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
09:10:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
09:10:00 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
09:10:00 - Status: TibState.PpsStopped
09:10:00 - Alarms: AlarmVector.ReadError
09:10:00 - Connection status: False TXclient_alive: False
09:10:00 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
09:10:00 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
09:10:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:10:00 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
09:10:00 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
09:10:00 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
09:10:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:10:00 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
09:10:00 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
09:10:00 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
09:10:02 - Connecting TIB to camera server at 10.10.4.12:222
09:10:02 - Starting TIB...
09:10:02 - Status: TibState.PpsStopped
09:10:02 - Alarms: AlarmVector.ReadError
09:10:02 - Connection status: False TXclient_alive: False
09:10:02 - Resetting run
09:10:02 - Wait for UCTS external trigger before enabling trigger...
09:10:02 - Status: TibState.Standby
09:10:02 - Alarms: AlarmVector.NoAlarm
09:10:02 - Connection status: False TXclient_alive: True
09:10:02 - Status: TibState.Standby
09:10:02 - Alarms: AlarmVector.NoAlarm
09:10:02 - Connection status: False TXclient_alive: True
09:10:03 - Status: TibState.Armed
09:10:03 - Alarms: AlarmVector.NoAlarm
09:10:03 - Connection status: True TXclient_alive: True
09:10:05 - Starting TIB triggers...
09:10:05 - Enabling trigger
09:10:05 - Status: TibState.Running
09:10:05 - Alarms: AlarmVector.NoAlarm
09:10:05 - Connection status: True TXclient_alive: True
09:10:07 - Configuring calibration box...
09:10:07 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=200 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
09:10:12 - Starting flashes...
09:10:24 - Checking for high voltage locked pixels...
09:10:37 - Stopping TIB...
09:10:37 - Status: TibState.Running
09:10:37 - Alarms: AlarmVector.ReadError
09:10:37 - Connection status: True TXclient_alive: True
09:10:37 - Disabling trigger
09:10:37 - Disabling PPS
09:10:38 - Status: TibState.PpsStopped
09:10:38 - Alarms: AlarmVector.ReadError
09:10:38 - Connection status: True TXclient_alive: True
09:10:38 - Closing TIB connection to camera server
09:10:40 - Status: TibState.PpsStopped
09:10:40 - Alarms: AlarmVector.ReadError
09:10:40 - Connection status: False TXclient_alive: False
09:10:40 - Run duration: 0:00:34
09:10:40 - Local camera triggers: 0
09:10:40 - Slow control triggers: 0
09:10:40 - Single photo-electron triggers: 0
09:10:40 - Calibration triggers: 19985
09:10:40 - Software triggers from UCTS: 0
09:10:40 - Pedestal triggers: 0
09:10:40 - Collected input triggers: 19985
09:10:40 - Busy triggers: 0
09:10:40 - Camera event triggers sent to clusters: 19985
09:10:43 - Calling method FSM.gotoReady in object FSM