11:12:02 - NMC is in state NmcState.Ready and knows of 0 drawer(s)
11:12:02 - Found 0 PPS errors.
11:12:09 - Starting task "Configure modules"
11:12:09 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200608/config_tower_2modules_HVguess6.NMC.xml
11:12:09 - Switching off high voltages in configuration
11:12:12 - Successfully configured 2 module(s)
11:12:13 - All front-end boards are programmed with firmware F55D1907
11:12:13 - All backplanes are programmed with firmware 15
11:12:13 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
11:12:13 - Found 0 PPS errors.
11:12:14 - Finished task "Configure modules"
11:12:15 - Starting task "Switch HVPA voltage state"
11:12:15 - Setting HVPA current limit to 12489.75 uA
11:12:15 - Setting HVPA ramp speed to 25 V/s
11:12:15 - Switching HVPA to state Nominal
11:12:22 - Setting HVPA current limits...
11:12:23 - High voltage locked channels will be checked every 30 s
11:12:23 - Finished task "Switch HVPA voltage state"
11:12:53 - Checking for high voltage locked pixels...
11:12:57 - Calling method FSM.gotoObserving in object FSM
11:13:08 - Starting task "Check high voltages"
11:13:08 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
11:13:08 - Actual voltage is between 969.90 V and 1124.23 V.
11:13:08 - Low voltages range between 100.00 V and 300.00 V. 
11:13:08 - Reference voltages range between 970.31 V and 1124.27 V. 
11:13:09 - Maximum difference between expected and actual voltages is 1024.23 V
11:13:09 - Maximum of current limits is 4969.06 uA
11:13:09 - Checking status of HVPA module in 2 drawer(s)...
11:13:09 - Checking status of HVPA channels in 2 drawer(s)...
11:13:09 - HV is stabilized in all channels.
11:13:09 - Finished task "Check high voltages"
11:13:10 - Starting NMC
11:13:10 - Clearing PPS error counters
11:13:19 - Configuring UCTS
11:13:19 - Configuring TIB...
11:13:19 - Setting TIB forced mode to False
11:13:19 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
11:13:19 - Status: TibState.PpsStopped
11:13:19 - Alarms: AlarmVector.ReadError
11:13:19 - Connection status: False TXclient_alive: False
11:13:19 - Entering set_external_delay
11:13:19 - Setting ExternalDelayLocal to 0.000 ns
11:13:19 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
11:13:19 - Entering set_external_delay
11:13:19 - Setting ExternalDelayCalibration to 65.000 ns
11:13:19 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
11:13:20 - Entering set_external_delay
11:13:20 - Setting ExternalDelaySphe to 150.000 ns
11:13:20 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
11:13:20 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
11:13:20 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
11:13:20 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
11:13:20 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
11:13:20 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
11:13:20 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
11:13:20 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
11:13:20 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
11:13:20 - Status: TibState.PpsStopped
11:13:20 - Alarms: AlarmVector.ReadError
11:13:20 - Connection status: False TXclient_alive: False
11:13:20 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
11:13:20 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
11:13:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:13:20 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
11:13:20 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
11:13:20 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
11:13:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:13:20 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
11:13:20 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
11:13:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
11:13:21 - Configuring calibration box...
11:13:21 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
11:13:23 - Checking for high voltage locked pixels...
11:13:25 - Connecting TIB to camera server at 10.10.4.12:222
11:13:25 - Starting TIB...
11:13:25 - Status: TibState.PpsStopped
11:13:25 - Alarms: AlarmVector.ReadError
11:13:25 - Connection status: False TXclient_alive: False
11:13:25 - Resetting run
11:13:25 - Wait for UCTS external trigger before enabling trigger...
11:13:25 - Status: TibState.Standby
11:13:25 - Alarms: AlarmVector.NoAlarm
11:13:25 - Connection status: False TXclient_alive: True
11:13:25 - Status: TibState.Standby
11:13:25 - Alarms: AlarmVector.NoAlarm
11:13:25 - Connection status: False TXclient_alive: True
11:13:26 - Status: TibState.Armed
11:13:26 - Alarms: AlarmVector.NoAlarm
11:13:26 - Connection status: True TXclient_alive: True
11:13:27 - Starting TIB triggers...
11:13:27 - Enabling trigger
11:13:27 - Status: TibState.Running
11:13:27 - Alarms: AlarmVector.NoAlarm
11:13:27 - Connection status: True TXclient_alive: True
11:13:29 - Starting flashes...
11:13:48 - Stopping TIB...
11:13:48 - Status: TibState.Running
11:13:48 - Alarms: AlarmVector.ReadError
11:13:48 - Connection status: True TXclient_alive: True
11:13:48 - Disabling trigger
11:13:48 - Disabling PPS
11:13:49 - Status: TibState.PpsStopped
11:13:49 - Alarms: AlarmVector.ReadError
11:13:49 - Connection status: True TXclient_alive: True
11:13:49 - Closing TIB connection to camera server
11:13:49 - Status: TibState.PpsStopped
11:13:49 - Alarms: AlarmVector.ReadError
11:13:49 - Connection status: False TXclient_alive: False
11:13:49 - Run duration: 0:00:22
11:13:49 - Local camera triggers: 0
11:13:49 - Slow control triggers: 0
11:13:49 - Single photo-electron triggers: 0
11:13:49 - Calibration triggers: 11922
11:13:49 - Software triggers from UCTS: 0
11:13:49 - Pedestal triggers: 0
11:13:49 - Collected input triggers: 11922
11:13:49 - Busy triggers: 0
11:13:49 - Camera event triggers sent to clusters: 11922
11:13:52 - Calling method FSM.gotoReady in object FSM
11:13:53 - Checking for high voltage locked pixels...
11:13:55 - Stopping NMC
11:13:55 - Found 0 PPS errors.