09:44:54 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:45:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:45:06 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:45:12 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:45:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:45:23 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
09:45:29 - Finished task "Powering modules..."
09:47:30 - Scanning interface p4p1 for non configured modules...
09:47:31 - Found 60 MAC address(es)
09:47:33 - ECC is in state EccState.Ready with status EccStatus.NoError
09:47:33 - Average temperature: 21.2 deg C
09:47:33 - Air temperature (T1-T6 and T9-T10): 21.2, 1255.0, 1254.0, -838.0, 1254.0, -838.0, 1254.0, -838.0 deg C
09:47:33 - Air differential pressure: 0.0 Pa
09:47:33 - Water temperature (T11-T12): 1253.0, -838.0 deg C
09:47:33 - Back doors are closed.
09:47:33 - Shutter is in state PartiallyOpen (error 0)
09:47:33 - Light sensors: [2.21, 2.63, 3.01, 3.31] V
09:47:33 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
09:47:33 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
09:47:33 - 24 V power supply no. 1 is enabled with a current of 45.400 A.
09:47:36 - Scanning interface p4p1 for non configured modules...
09:47:36 - Found 61 MAC address(es)
09:48:21 - Starting task "Configure modules"
09:48:22 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200608/config_tower_2modules_HVguess5.NMC.xml
09:48:22 - Switching off high voltages in configuration
09:48:27 - Successfully configured 2 module(s)
09:48:28 - All front-end boards are programmed with firmware F55D1907
09:48:28 - All backplanes are programmed with firmware 15
09:48:29 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
09:48:29 - Found 0 PPS errors.
09:48:29 - Finished task "Configure modules"
09:48:45 - Starting task "Switch HVPA voltage state"
09:48:45 - Setting HVPA current limit to 12489.75 uA
09:48:46 - Setting HVPA ramp speed to 25 V/s
09:48:46 - Switching HVPA to state Nominal
09:48:53 - Setting HVPA current limits...
09:48:55 - Finished task "Switch HVPA voltage state"
09:49:53 - High voltage locked channels will be checked every 30 s
09:50:23 - Checking for high voltage locked pixels...
09:50:53 - Checking for high voltage locked pixels...
09:51:23 - Checking for high voltage locked pixels...
09:51:53 - Checking for high voltage locked pixels...
09:52:23 - Checking for high voltage locked pixels...
09:52:53 - Checking for high voltage locked pixels...
09:53:23 - Checking for high voltage locked pixels...
09:53:53 - Checking for high voltage locked pixels...
09:54:23 - Checking for high voltage locked pixels...
09:54:53 - Checking for high voltage locked pixels...
09:55:23 - Checking for high voltage locked pixels...
09:55:53 - Checking for high voltage locked pixels...
09:56:23 - Checking for high voltage locked pixels...
09:56:53 - Checking for high voltage locked pixels...
09:57:23 - Checking for high voltage locked pixels...
09:57:53 - Checking for high voltage locked pixels...
09:58:23 - Checking for high voltage locked pixels...
09:58:53 - Checking for high voltage locked pixels...
09:59:23 - Checking for high voltage locked pixels...
09:59:53 - Checking for high voltage locked pixels...
10:00:23 - Checking for high voltage locked pixels...
10:00:53 - Checking for high voltage locked pixels...
10:01:23 - Checking for high voltage locked pixels...
10:01:53 - Checking for high voltage locked pixels...
10:02:23 - Checking for high voltage locked pixels...
10:02:53 - Checking for high voltage locked pixels...
10:03:23 - Checking for high voltage locked pixels...
10:03:53 - Checking for high voltage locked pixels...
10:04:23 - Checking for high voltage locked pixels...
10:04:53 - Checking for high voltage locked pixels...
10:05:23 - Checking for high voltage locked pixels...
10:05:32 - Starting task "Power off channels not corresponding to a configured module"
10:05:32 - Powering off all but 2 DTC channel(s)
10:05:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:39 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:41 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:43 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:44 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:46 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:51 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:53 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:53 - Checking for high voltage locked pixels...
10:05:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:57 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:05:58 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:02 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:04 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:05 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:07 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:09 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:11 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:12 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:14 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:16 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:18 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:19 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:21 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:23 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:23 - Checking for high voltage locked pixels...
10:06:25 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:26 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:28 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:30 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:32 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:33 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:39 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:42 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:44 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:46 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:51 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:53 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:53 - Checking for high voltage locked pixels...
10:06:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:56 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:06:58 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:01 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:03 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:05 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:07 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:08 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:10 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:12 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:14 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:16 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:17 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:19 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:21 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:23 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:23 - Checking for high voltage locked pixels...
10:07:24 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:26 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:28 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:30 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:33 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:35 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:38 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:42 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:44 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:45 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:49 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:51 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:52 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:53 - Checking for high voltage locked pixels...
10:07:54 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:56 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:58 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:07:59 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:01 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:03 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:05 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:06 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:08 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:10 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:12 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:13 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:15 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:17 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:19 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:20 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:22 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:23 - Checking for high voltage locked pixels...
10:08:24 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:26 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:29 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 11 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:33 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:34 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:36 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:38 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:40 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 1 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:41 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 2 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:43 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 3 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:45 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 4 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:47 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 5 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:48 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 6 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:50 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 7 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:52 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 8 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:53 - Checking for high voltage locked pixels...
10:08:54 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 9 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 10 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:57 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 12 --power_off' on Digital Trigger Crate at 10.10.4.57
10:08:59 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 13 --power_off' on Digital Trigger Crate at 10.10.4.57
10:09:01 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 14 --power_off' on Digital Trigger Crate at 10.10.4.57
10:09:02 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --channel 15 --power_off' on Digital Trigger Crate at 10.10.4.57
10:09:04 - Finished task "Power off channels not corresponding to a configured module"
10:09:23 - Checking for high voltage locked pixels...
10:09:27 - Starting task "Check high voltages"
10:09:27 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
10:09:27 - Actual voltage is between 969.90 V and 1085.19 V.
10:09:27 - Low voltages range between 100.00 V and 300.00 V. 
10:09:28 - Reference voltages range between 970.31 V and 1084.70 V. 
10:09:28 - Maximum difference between expected and actual voltages is 984.58 V
10:09:28 - Maximum of current limits is 4969.06 uA
10:09:28 - Checking status of HVPA module in 2 drawer(s)...
10:09:28 - Checking status of HVPA channels in 2 drawer(s)...
10:09:28 - HV is stabilized in all channels.
10:09:28 - Finished task "Check high voltages"
10:09:33 - Calling method FSM.gotoObserving in object FSM
10:09:41 - Stopping NMC
10:09:41 - Found PPS errors: 255 in drawer 93
10:09:43 - Starting NMC
10:09:43 - Clearing PPS error counters
10:09:53 - Checking for high voltage locked pixels...
10:10:20 - Configuring UCTS
10:10:20 - Configuring TIB...
10:10:20 - Setting TIB forced mode to False
10:10:20 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:10:20 - Status: TibState.RunStopped
10:10:20 - Alarms: AlarmVector.NoAlarm
10:10:20 - Connection status: False TXclient_alive: False
10:10:20 - Disabling PPS
10:10:22 - Status: TibState.PpsStopped
10:10:22 - Alarms: AlarmVector.NoAlarm
10:10:22 - Connection status: False TXclient_alive: False
10:10:22 - Entering set_external_delay
10:10:22 - Setting ExternalDelayLocal to 0.000 ns
10:10:22 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:10:22 - Entering set_external_delay
10:10:22 - Setting ExternalDelayCalibration to 65.000 ns
10:10:22 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:10:22 - Entering set_external_delay
10:10:22 - Setting ExternalDelaySphe to 150.000 ns
10:10:22 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:10:23 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:10:23 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:10:23 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:10:23 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:10:23 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:10:23 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:10:23 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:10:23 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:10:23 - Status: TibState.PpsStopped
10:10:23 - Alarms: AlarmVector.NoAlarm
10:10:23 - Connection status: False TXclient_alive: False
10:10:23 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:10:23 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:10:23 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:10:23 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:10:23 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:10:23 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:10:23 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:10:23 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:10:23 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:10:23 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:10:23 - Checking for high voltage locked pixels...
10:10:26 - Configuring calibration box...
10:10:27 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
10:10:30 - Connecting TIB to camera server at 10.10.4.12:222
10:10:30 - Starting TIB...
10:10:30 - Status: TibState.PpsStopped
10:10:30 - Alarms: AlarmVector.NoAlarm
10:10:30 - Connection status: False TXclient_alive: False
10:10:30 - Resetting run
10:10:30 - Wait for UCTS external trigger before enabling trigger...
10:10:30 - Status: TibState.Standby
10:10:30 - Alarms: AlarmVector.NoAlarm
10:10:30 - Connection status: False TXclient_alive: False
10:10:30 - Status: TibState.Standby
10:10:30 - Alarms: AlarmVector.NoAlarm
10:10:30 - Connection status: False TXclient_alive: False
10:10:31 - Status: TibState.Armed
10:10:31 - Alarms: AlarmVector.NoAlarm
10:10:31 - Connection status: True TXclient_alive: True
10:10:33 - Starting TIB triggers...
10:10:33 - Enabling trigger
10:10:33 - Status: TibState.Running
10:10:33 - Alarms: AlarmVector.NoAlarm
10:10:33 - Connection status: True TXclient_alive: True
10:10:35 - Starting flashes...
10:10:53 - Checking for high voltage locked pixels...
10:10:54 - Stopping TIB...
10:10:54 - Status: TibState.Running
10:10:54 - Alarms: AlarmVector.ReadError
10:10:55 - Connection status: True TXclient_alive: True
10:10:55 - Disabling trigger
10:10:55 - Disabling PPS
10:10:56 - Status: TibState.PpsStopped
10:10:56 - Alarms: AlarmVector.ReadError
10:10:56 - Connection status: True TXclient_alive: True
10:10:56 - Closing TIB connection to camera server
10:10:57 - Status: TibState.PpsStopped
10:10:57 - Alarms: AlarmVector.ReadError
10:10:57 - Connection status: False TXclient_alive: False
10:10:57 - Run duration: 0:00:24
10:10:57 - Local camera triggers: 0
10:10:57 - Slow control triggers: 0
10:10:57 - Single photo-electron triggers: 0
10:10:57 - Calibration triggers: 11943
10:10:57 - Software triggers from UCTS: 0
10:10:57 - Pedestal triggers: 0
10:10:57 - Collected input triggers: 11943
10:10:57 - Busy triggers: 0
10:10:57 - Camera event triggers sent to clusters: 11943
10:11:01 - Calling method FSM.gotoReady in object FSM