16:30:42 - ECC is in state EccState.Monitoring with status EccStatus.NoError
16:30:42 - Average temperature: 19.7 deg C
16:30:42 - Air temperature (T1-T6 and T9-T10): 19.7, -838.0, 1254.0, -838.0, 1254.0, 1254.0, -838.0, -838.0 deg C
16:30:42 - Air differential pressure: 0.0 Pa
16:30:42 - Water temperature (T11-T12): -838.0, -838.0 deg C
16:30:42 - Back doors are closed.
16:30:42 - Shutter is in state PartiallyOpen (error 0)
16:30:42 - Light sensors: [2.23, 2.64, 3.03, 3.33] V
16:30:42 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:30:42 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:30:42 - 24 V power supply no. 1 is enabled with a current of 44.800 A.
16:31:23 - No server with URI='urn:NI-cRIO-9068-01d06bf6-MST-CEA:UnifiedAutomation:UaServerCpp' has been discovered. The client could not discover a single server.
16:33:03 - ECC is in state EccState.Safe with status EccStatus.NoError
16:33:03 - Average temperature: 19.7 deg C
16:33:03 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, -838.0, 1254.0, 1254.0, 1254.0, -838.0, 1253.0 deg C
16:33:03 - Air differential pressure: 0.0 Pa
16:33:03 - Water temperature (T11-T12): -838.0, 1254.0 deg C
16:33:03 - Back doors are closed.
16:33:03 - Shutter is in state PartiallyOpen (error 0)
16:33:03 - Light sensors: [2.42, 2.9, 3.3, 3.62] V
16:33:03 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:33:03 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:33:03 - 24 V power supply no. 1 is disabled with a current of 6.150 A.
16:33:05 - Starting task "Prepare ECC"
16:33:05 - Preparing ECC...
16:33:05 - Setting ECC temperature range for Ready state to [16.000000, 36.000000]
16:33:05 - Setting ECC mode to EccTransition.Ready
16:33:06 - Received ECC state change notification: EccState.Safe
16:33:11 - Received ECC state change notification: EccState.Ready
16:33:12 - Setting power supply box SPE relay to True
16:33:12 - Finished task "Prepare ECC"
16:33:14 - ECC is in state EccState.Ready with status EccStatus.NoError
16:33:14 - Average temperature: 19.7 deg C
16:33:14 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, -838.0, 1254.0, 1254.0, 1254.0, 1254.0, 1253.0 deg C
16:33:14 - Air differential pressure: 0.0 Pa
16:33:14 - Water temperature (T11-T12): 1253.0, -838.0 deg C
16:33:14 - Back doors are closed.
16:33:14 - Shutter is in state PartiallyOpen (error 0)
16:33:14 - Light sensors: [2.41, 2.93, 3.4, 3.69] V
16:33:14 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:33:14 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:33:14 - 24 V power supply no. 1 is enabled with a current of 0.160 A.
16:33:19 - Starting task "Powering modules..."
16:33:19 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.57
16:33:20 - Finished task "Powering modules..."
16:33:22 - Starting task "Powering modules..."
16:33:22 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:33:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:33:33 - Executing command '/opt/cta/bin/cta_ctrl --slot 6 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:33:39 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:33:45 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:33:51 - Executing command '/opt/cta/bin/cta_ctrl --slot 14 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:33:56 - Executing command '/opt/cta/bin/cta_ctrl --slot 15 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:34:02 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:34:08 - Finished task "Powering modules..."
16:34:13 - Scanning interface p4p1 for non configured modules...
16:34:19 - Found 0 MAC address(es)
16:34:23 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:23 - Average temperature: 19.7 deg C
16:34:23 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, 1254.0, 1254.0, -838.0, -838.0, -838.0, 1253.0 deg C
16:34:23 - Air differential pressure: 0.0 Pa
16:34:23 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
16:34:23 - Back doors are closed.
16:34:23 - Shutter is in state PartiallyOpen (error 0)
16:34:23 - Light sensors: [2.39, 2.85, 3.28, 3.6] V
16:34:23 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:23 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:23 - 24 V power supply no. 1 is enabled with a current of 40.900 A.
16:34:25 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:25 - Average temperature: 19.7 deg C
16:34:25 - Air temperature (T1-T6 and T9-T10): 19.7, -838.0, 1254.0, -838.0, 1254.0, 1254.0, -838.0, -838.0 deg C
16:34:25 - Air differential pressure: 0.0 Pa
16:34:25 - Water temperature (T11-T12): -838.0, -838.0 deg C
16:34:25 - Back doors are closed.
16:34:25 - Shutter is in state PartiallyOpen (error 0)
16:34:25 - Light sensors: [2.4, 2.86, 3.28, 3.6] V
16:34:25 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:25 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:25 - 24 V power supply no. 1 is enabled with a current of 40.900 A.
16:34:26 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:26 - Average temperature: 19.7 deg C
16:34:26 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, -838.0, -838.0, 1254.0, 1254.0, 1254.0, 1253.0 deg C
16:34:26 - Air differential pressure: 0.0 Pa
16:34:26 - Water temperature (T11-T12): -838.0, 1254.0 deg C
16:34:26 - Back doors are closed.
16:34:26 - Shutter is in state PartiallyOpen (error 0)
16:34:26 - Light sensors: [2.38, 2.85, 3.27, 3.59] V
16:34:26 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:26 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:26 - 24 V power supply no. 1 is enabled with a current of 40.900 A.
16:34:27 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:27 - Average temperature: 19.7 deg C
16:34:27 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, 1254.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
16:34:27 - Air differential pressure: 0.0 Pa
16:34:27 - Water temperature (T11-T12): -838.0, -838.0 deg C
16:34:27 - Back doors are closed.
16:34:27 - Shutter is in state PartiallyOpen (error 0)
16:34:27 - Light sensors: [2.38, 2.85, 3.27, 3.59] V
16:34:27 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:27 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:27 - 24 V power supply no. 1 is enabled with a current of 40.900 A.
16:34:29 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:29 - Average temperature: 19.7 deg C
16:34:29 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, 1254.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
16:34:29 - Air differential pressure: 0.0 Pa
16:34:29 - Water temperature (T11-T12): -838.0, -838.0 deg C
16:34:29 - Back doors are closed.
16:34:29 - Shutter is in state PartiallyOpen (error 0)
16:34:29 - Light sensors: [2.39, 2.84, 3.27, 3.58] V
16:34:29 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:29 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:29 - 24 V power supply no. 1 is enabled with a current of 40.900 A.
16:34:35 - Status: TibState.RunStopped
16:34:35 - Alarms: AlarmVector.NoAlarm
16:34:35 - Connection status: False TXclient_alive: False
16:34:35 - External delays: Local=3825.000 ns, Calibration=3825.000 ns, Sphe=3825.000 ns
16:34:35 - Trigger mask: 0x51 = TriggerMask.SlowControl|Software|Mono
16:34:35 - Input mask: 0x7
16:34:35 - Disable BUSY: False
16:34:35 - Extra BUSY Delay: 0.0
16:34:35 - Temperature: 28.38
16:34:39 - Scanning interface p4p1 for non configured modules...
16:34:46 - Found 0 MAC address(es)
16:34:47 - Scanning interface p4p1 for non configured modules...
16:34:54 - Found 0 MAC address(es)
16:34:57 - ECC is in state EccState.Ready with status EccStatus.NoError
16:34:57 - Average temperature: 19.7 deg C
16:34:57 - Air temperature (T1-T6 and T9-T10): 19.7, -838.0, 1254.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0 deg C
16:34:57 - Air differential pressure: 0.0 Pa
16:34:57 - Water temperature (T11-T12): 1253.0, 1254.0 deg C
16:34:57 - Back doors are closed.
16:34:57 - Shutter is in state PartiallyOpen (error 0)
16:34:57 - Light sensors: [2.35, 2.8, 3.21, 3.53] V
16:34:57 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:34:57 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:34:57 - 24 V power supply no. 1 is enabled with a current of 43.500 A.
16:35:04 - ECC is in state EccState.Ready with status EccStatus.NoError
16:35:04 - Average temperature: 19.7 deg C
16:35:04 - Air temperature (T1-T6 and T9-T10): 19.7, 1255.0, 1254.0, -838.0, -838.0, 1254.0, -838.0, -838.0 deg C
16:35:04 - Air differential pressure: 0.0 Pa
16:35:04 - Water temperature (T11-T12): -838.0, 1254.0 deg C
16:35:04 - Back doors are closed.
16:35:04 - Shutter is in state PartiallyOpen (error 0)
16:35:04 - Light sensors: [2.33, 2.78, 3.19, 3.51] V
16:35:04 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
16:35:04 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
16:35:04 - 24 V power supply no. 1 is enabled with a current of 44.900 A.
16:35:07 - Scanning interface p4p1 for non configured modules...
16:35:07 - Found 61 MAC address(es)
16:35:16 - Starting task "Configure modules"
16:35:16 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200605/config_tower_2modules_HVguess3.NMC.xml
16:35:16 - Switching off high voltages in configuration
16:35:19 - Successfully configured 2 module(s)
16:35:20 - All front-end boards are programmed with firmware F55D1907
16:35:20 - All backplanes are programmed with firmware 15
16:35:21 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:35:21 - Found 0 PPS errors.
16:35:21 - Finished task "Configure modules"
16:35:27 - Starting task "Switch HVPA voltage state"
16:35:27 - Setting HVPA current limit to 12489.75 uA
16:35:27 - Setting HVPA ramp speed to 25 V/s
16:35:27 - Switching HVPA to state Nominal
16:35:28 - High voltage locked channels will be checked every 30 s
16:35:34 - Setting HVPA current limits...
16:35:35 - Finished task "Switch HVPA voltage state"
16:35:54 - Calling method FSM.gotoObserving in object FSM
16:35:58 - Checking for high voltage locked pixels...
16:36:28 - Checking for high voltage locked pixels...
16:36:33 - Starting task "Check high voltages"
16:36:33 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
16:36:33 - Actual voltage is between 969.90 V and 1085.19 V.
16:36:33 - Low voltages range between 100.00 V and 300.00 V. 
16:36:34 - Reference voltages range between 970.31 V and 1084.70 V. 
16:36:34 - Maximum difference between expected and actual voltages is 985.19 V
16:36:34 - Maximum of current limits is 4969.06 uA
16:36:34 - Checking status of HVPA module in 2 drawer(s)...
16:36:34 - Checking status of HVPA channels in 2 drawer(s)...
16:36:34 - HV is stabilized in all channels.
16:36:34 - Finished task "Check high voltages"
16:36:39 - Configuring calibration box...
16:36:39 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
16:36:43 - Configuring UCTS
16:36:43 - Configuring TIB...
16:36:43 - Setting TIB forced mode to False
16:36:43 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:36:43 - Status: TibState.RunStopped
16:36:43 - Alarms: AlarmVector.NoAlarm
16:36:43 - Connection status: False TXclient_alive: False
16:36:43 - Disabling PPS
16:36:45 - Status: TibState.PpsStopped
16:36:45 - Alarms: AlarmVector.NoAlarm
16:36:45 - Connection status: False TXclient_alive: False
16:36:45 - Entering set_external_delay
16:36:45 - Setting ExternalDelayLocal to 0.000 ns
16:36:45 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:36:46 - Entering set_external_delay
16:36:46 - Setting ExternalDelayCalibration to 65.000 ns
16:36:46 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:36:46 - Entering set_external_delay
16:36:46 - Setting ExternalDelaySphe to 150.000 ns
16:36:46 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:36:46 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
16:36:46 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:36:46 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:36:46 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:36:46 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:36:46 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:36:46 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:36:46 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:36:46 - Status: TibState.PpsStopped
16:36:46 - Alarms: AlarmVector.NoAlarm
16:36:46 - Connection status: False TXclient_alive: False
16:36:46 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:36:46 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:36:46 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:36:46 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:36:46 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:36:46 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:36:46 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:36:46 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:36:46 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:36:46 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:36:47 - Connecting TIB to camera server at 10.10.4.12:222
16:36:47 - Starting TIB...
16:36:47 - Status: TibState.PpsStopped
16:36:47 - Alarms: AlarmVector.NoAlarm
16:36:47 - Connection status: False TXclient_alive: False
16:36:47 - Resetting run
16:36:47 - Wait for UCTS external trigger before enabling trigger...
16:36:47 - Status: TibState.Standby
16:36:47 - Alarms: AlarmVector.NoAlarm
16:36:47 - Connection status: False TXclient_alive: False
16:36:47 - Status: TibState.Standby
16:36:47 - Alarms: AlarmVector.NoAlarm
16:36:47 - Connection status: False TXclient_alive: True
16:36:48 - Status: TibState.Armed
16:36:48 - Alarms: AlarmVector.NoAlarm
16:36:48 - Connection status: True TXclient_alive: True
16:36:50 - Starting TIB triggers...
16:36:50 - Enabling trigger
16:36:50 - Status: TibState.Running
16:36:50 - Alarms: AlarmVector.NoAlarm
16:36:50 - Connection status: True TXclient_alive: True
16:36:53 - Starting flashes...
16:36:58 - Checking for high voltage locked pixels...
16:37:15 - Stopping TIB...
16:37:15 - Status: TibState.Running
16:37:15 - Alarms: AlarmVector.ReadError
16:37:15 - Connection status: True TXclient_alive: True
16:37:15 - Disabling trigger
16:37:15 - Disabling PPS
16:37:16 - Status: TibState.PpsStopped
16:37:16 - Alarms: AlarmVector.ReadError
16:37:16 - Connection status: True TXclient_alive: True
16:37:16 - Closing TIB connection to camera server
16:37:18 - Calling method FSM.gotoReady in object FSM
16:37:19 - Calling method FSM.gotoObserving in object FSM
16:37:28 - Checking for high voltage locked pixels...
16:37:31 - Stopping NMC
16:37:31 - Found PPS errors: 20 in drawer 82, 24 in drawer 93
16:37:36 - Starting NMC
16:37:36 - Clearing PPS error counters
16:37:44 - Configuring calibration box...
16:37:44 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
16:37:46 - Configuring UCTS
16:37:47 - Configuring TIB...
16:37:47 - Setting TIB forced mode to False
16:37:47 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:37:47 - Status: TibState.PpsStopped
16:37:47 - Alarms: AlarmVector.ReadError
16:37:47 - Connection status: False TXclient_alive: False
16:37:47 - Entering set_external_delay
16:37:47 - Setting ExternalDelayLocal to 0.000 ns
16:37:47 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:37:47 - Entering set_external_delay
16:37:47 - Setting ExternalDelayCalibration to 65.000 ns
16:37:47 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:37:47 - Entering set_external_delay
16:37:47 - Setting ExternalDelaySphe to 150.000 ns
16:37:47 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:37:47 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
16:37:47 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:37:47 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:37:47 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:37:47 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:37:47 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:37:47 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:37:47 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:37:47 - Status: TibState.PpsStopped
16:37:47 - Alarms: AlarmVector.ReadError
16:37:47 - Connection status: False TXclient_alive: False
16:37:47 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:37:47 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:37:47 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:37:47 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:37:47 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:37:47 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:37:47 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:37:47 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:37:47 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:37:47 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:37:48 - Connecting TIB to camera server at 10.10.4.12:222
16:37:48 - Starting TIB...
16:37:48 - Status: TibState.PpsStopped
16:37:48 - Alarms: AlarmVector.ReadError
16:37:48 - Connection status: False TXclient_alive: False
16:37:48 - Resetting run
16:37:48 - Wait for UCTS external trigger before enabling trigger...
16:37:48 - Status: TibState.Standby
16:37:48 - Alarms: AlarmVector.NoAlarm
16:37:48 - Connection status: False TXclient_alive: True
16:37:48 - Status: TibState.Standby
16:37:48 - Alarms: AlarmVector.NoAlarm
16:37:48 - Connection status: False TXclient_alive: True
16:37:49 - Status: TibState.Armed
16:37:49 - Alarms: AlarmVector.NoAlarm
16:37:49 - Connection status: True TXclient_alive: True
16:37:50 - Starting TIB triggers...
16:37:50 - Enabling trigger
16:37:50 - Status: TibState.Running
16:37:50 - Alarms: AlarmVector.NoAlarm
16:37:50 - Connection status: True TXclient_alive: True
16:37:54 - Starting flashes...
16:37:58 - Checking for high voltage locked pixels...
16:38:10 - Stopping TIB...
16:38:10 - Status: TibState.Running
16:38:10 - Alarms: AlarmVector.ReadError
16:38:10 - Connection status: True TXclient_alive: True
16:38:10 - Disabling trigger
16:38:10 - Disabling PPS
16:38:11 - Status: TibState.PpsStopped
16:38:11 - Alarms: AlarmVector.ReadError
16:38:11 - Connection status: True TXclient_alive: True
16:38:11 - Closing TIB connection to camera server
16:38:12 - Status: TibState.PpsStopped
16:38:12 - Alarms: AlarmVector.ReadError
16:38:12 - Connection status: False TXclient_alive: False
16:38:12 - Run duration: 0:00:21
16:38:12 - Local camera triggers: 0
16:38:12 - Slow control triggers: 0
16:38:12 - Single photo-electron triggers: 0
16:38:12 - Calibration triggers: 11947
16:38:12 - Software triggers from UCTS: 0
16:38:12 - Pedestal triggers: 0
16:38:12 - Collected input triggers: 11947
16:38:12 - Busy triggers: 0
16:38:12 - Camera event triggers sent to clusters: 11947
16:38:15 - Calling method FSM.gotoReady in object FSM
16:38:28 - Checking for high voltage locked pixels...