16:06:39 - Stopping NMC
16:06:39 - Found 0 PPS errors.
16:06:40 - Resetting NMC
16:06:42 - Starting task "Configure modules"
16:06:42 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200605/config_tower_2modules_HVguess2.NMC.xml
16:06:42 - Switching off high voltages in configuration
16:06:45 - Successfully configured 2 module(s)
16:06:46 - All front-end boards are programmed with firmware F55D1907
16:06:46 - Checking for high voltage locked pixels...
16:06:46 - All backplanes are programmed with firmware 15
16:06:47 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
16:06:47 - Found PPS errors: 255 in drawer 93
16:06:47 - Finished task "Configure modules"
16:06:49 - Starting task "Switch HVPA voltage state"
16:06:49 - Setting HVPA current limit to 12489.75 uA
16:06:50 - Setting HVPA ramp speed to 25 V/s
16:06:50 - Switching HVPA to state Nominal
16:06:57 - Setting HVPA current limits...
16:06:58 - Finished task "Switch HVPA voltage state"
16:07:16 - Checking for high voltage locked pixels...
16:07:26 - Starting task "Check high voltages"
16:07:26 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
16:07:27 - Actual voltage is between 969.90 V and 1084.58 V.
16:07:27 - Low voltages range between 100.00 V and 300.00 V. 
16:07:27 - Reference voltages range between 970.31 V and 1084.70 V. 
16:07:27 - Maximum difference between expected and actual voltages is 983.36 V
16:07:27 - Maximum of current limits is 4969.06 uA
16:07:27 - Checking status of HVPA module in 2 drawer(s)...
16:07:27 - Checking status of HVPA channels in 2 drawer(s)...
16:07:28 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
16:07:28 - Finished task "Check high voltages"
16:07:34 - Starting task "Check high voltages"
16:07:34 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
16:07:34 - Actual voltage is between 969.90 V and 1084.58 V.
16:07:34 - Low voltages range between 100.00 V and 300.00 V. 
16:07:35 - Reference voltages range between 970.31 V and 1084.70 V. 
16:07:35 - Maximum difference between expected and actual voltages is 983.36 V
16:07:35 - Maximum of current limits is 4969.06 uA
16:07:35 - Checking status of HVPA module in 2 drawer(s)...
16:07:35 - Checking status of HVPA channels in 2 drawer(s)...
16:07:35 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
16:07:36 - Finished task "Check high voltages"
16:07:43 - Starting task "Check high voltages"
16:07:43 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
16:07:44 - Actual voltage is between 969.90 V and 1084.58 V.
16:07:44 - Low voltages range between 100.00 V and 300.00 V. 
16:07:44 - Reference voltages range between 970.31 V and 1084.70 V. 
16:07:44 - Maximum difference between expected and actual voltages is 983.36 V
16:07:44 - Maximum of current limits is 4969.06 uA
16:07:44 - Checking status of HVPA module in 2 drawer(s)...
16:07:44 - Checking status of HVPA channels in 2 drawer(s)...
16:07:45 - HV is stabilized in all channels.
16:07:45 - Finished task "Check high voltages"
16:07:46 - Checking for high voltage locked pixels...
16:07:47 - Stopping NMC
16:07:48 - Found PPS errors: 255 in drawer 93
16:07:50 - Starting NMC
16:07:50 - Clearing PPS error counters
16:08:16 - Checking for high voltage locked pixels...
16:08:29 - Calling method FSM.gotoObserving in object FSM
16:08:35 - Configuring calibration box...
16:08:35 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
16:08:38 - Configuring UCTS
16:08:38 - Configuring TIB...
16:08:38 - Setting TIB forced mode to False
16:08:38 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:08:38 - Status: TibState.PpsStopped
16:08:38 - Alarms: AlarmVector.ReadError
16:08:38 - Connection status: False TXclient_alive: False
16:08:38 - Entering set_external_delay
16:08:38 - Setting ExternalDelayLocal to 0.000 ns
16:08:38 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:08:38 - Entering set_external_delay
16:08:38 - Setting ExternalDelayCalibration to 65.000 ns
16:08:38 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:08:38 - Entering set_external_delay
16:08:38 - Setting ExternalDelaySphe to 150.000 ns
16:08:38 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:08:39 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
16:08:39 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:08:39 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:08:39 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:08:39 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:08:39 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:08:39 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:08:39 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:08:39 - Status: TibState.PpsStopped
16:08:39 - Alarms: AlarmVector.ReadError
16:08:39 - Connection status: False TXclient_alive: False
16:08:39 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:08:39 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:08:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:08:39 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:08:39 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:08:39 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:08:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:08:39 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:08:39 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:08:39 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:08:41 - Connecting TIB to camera server at 10.10.4.12:222
16:08:41 - Starting TIB...
16:08:41 - Status: TibState.PpsStopped
16:08:41 - Alarms: AlarmVector.ReadError
16:08:42 - Connection status: False TXclient_alive: False
16:08:42 - Resetting run
16:08:42 - Wait for UCTS external trigger before enabling trigger...
16:08:42 - Status: TibState.Standby
16:08:42 - Alarms: AlarmVector.NoAlarm
16:08:42 - Connection status: False TXclient_alive: True
16:08:42 - Status: TibState.Standby
16:08:42 - Alarms: AlarmVector.NoAlarm
16:08:42 - Connection status: False TXclient_alive: True
16:08:43 - Status: TibState.Armed
16:08:43 - Alarms: AlarmVector.NoAlarm
16:08:43 - Connection status: True TXclient_alive: True
16:08:44 - Starting TIB triggers...
16:08:44 - Enabling trigger
16:08:44 - Status: TibState.Running
16:08:44 - Alarms: AlarmVector.NoAlarm
16:08:44 - Connection status: True TXclient_alive: True
16:08:46 - Checking for high voltage locked pixels...
16:08:48 - Starting flashes...
16:09:15 - Stopping TIB...
16:09:15 - Status: TibState.Running
16:09:15 - Alarms: AlarmVector.ReadError
16:09:15 - Connection status: True TXclient_alive: True
16:09:15 - Disabling trigger
16:09:15 - Disabling PPS
16:09:16 - Status: TibState.PpsStopped
16:09:16 - Alarms: AlarmVector.ReadError
16:09:16 - Connection status: True TXclient_alive: True
16:09:16 - Closing TIB connection to camera server
16:09:16 - Checking for high voltage locked pixels...
16:09:17 - Status: TibState.PpsStopped
16:09:17 - Alarms: AlarmVector.ReadError
16:09:17 - Connection status: False TXclient_alive: False
16:09:17 - Run duration: 0:00:32
16:09:17 - Local camera triggers: 0
16:09:17 - Slow control triggers: 0
16:09:17 - Single photo-electron triggers: 0
16:09:17 - Calibration triggers: 11999
16:09:17 - Software triggers from UCTS: 0
16:09:17 - Pedestal triggers: 0
16:09:17 - Collected input triggers: 11999
16:09:17 - Busy triggers: 0
16:09:17 - Camera event triggers sent to clusters: 11999
16:09:21 - Calling method FSM.gotoReady in object FSM