15:44:10 - Resetting NMC
15:44:12 - Starting task "Configure modules"
15:44:12 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200605/config_tower_2modules_HVguess1.NMC.xml
15:44:12 - Switching off high voltages in configuration
15:44:15 - Successfully configured 2 module(s)
15:44:16 - All front-end boards are programmed with firmware F55D1907
15:44:16 - All backplanes are programmed with firmware 15
15:44:16 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
15:44:16 - Found PPS errors: 12 in drawer 93
15:44:16 - Checking for high voltage locked pixels...
15:44:16 - Finished task "Configure modules"
15:44:27 - Starting task "Switch HVPA voltage state"
15:44:27 - Setting HVPA current limit to 12489.75 uA
15:44:27 - Setting HVPA ramp speed to 25 V/s
15:44:27 - Switching HVPA to state Nominal
15:44:35 - Setting HVPA current limits...
15:44:36 - Finished task "Switch HVPA voltage state"
15:44:46 - Checking for high voltage locked pixels...
15:45:02 - Calling method FSM.gotoObserving in object FSM
15:45:16 - Checking for high voltage locked pixels...
15:45:18 - Starting task "Check high voltages"
15:45:18 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
15:45:18 - Actual voltage is between 965.02 V and 1083.36 V.
15:45:18 - Low voltages range between 100.00 V and 300.00 V. 
15:45:19 - Reference voltages range between 965.38 V and 1083.25 V. 
15:45:19 - Maximum difference between expected and actual voltages is 981.53 V
15:45:19 - Maximum of current limits is 4969.06 uA
15:45:19 - Checking status of HVPA module in 2 drawer(s)...
15:45:19 - Checking status of HVPA channels in 2 drawer(s)...
15:45:19 - HV is stabilized in all channels.
15:45:19 - Finished task "Check high voltages"
15:45:25 - Starting NMC
15:45:25 - Clearing PPS error counters
15:45:30 - Configuring calibration box...
15:45:30 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
15:45:35 - Configuring UCTS
15:45:35 - Configuring TIB...
15:45:35 - Setting TIB forced mode to False
15:45:35 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:45:35 - Status: TibState.PpsStopped
15:45:35 - Alarms: AlarmVector.ReadError
15:45:35 - Connection status: False TXclient_alive: False
15:45:35 - Entering set_external_delay
15:45:35 - Setting ExternalDelayLocal to 0.000 ns
15:45:35 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:45:35 - Entering set_external_delay
15:45:35 - Setting ExternalDelayCalibration to 65.000 ns
15:45:35 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:45:35 - Entering set_external_delay
15:45:35 - Setting ExternalDelaySphe to 150.000 ns
15:45:35 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:45:35 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:45:35 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:45:35 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:45:35 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:45:35 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:45:35 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:45:35 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:45:35 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:45:35 - Status: TibState.PpsStopped
15:45:35 - Alarms: AlarmVector.ReadError
15:45:35 - Connection status: False TXclient_alive: False
15:45:35 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:45:35 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:45:35 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:45:35 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:45:35 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:45:35 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:45:35 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:45:35 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:45:35 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:45:35 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:45:37 - Connecting TIB to camera server at 10.10.4.12:222
15:45:37 - Starting TIB...
15:45:37 - Status: TibState.PpsStopped
15:45:37 - Alarms: AlarmVector.ReadError
15:45:37 - Connection status: False TXclient_alive: False
15:45:37 - Resetting run
15:45:37 - Wait for UCTS external trigger before enabling trigger...
15:45:37 - Status: TibState.Standby
15:45:37 - Alarms: AlarmVector.NoAlarm
15:45:37 - Connection status: False TXclient_alive: True
15:45:37 - Status: TibState.Standby
15:45:37 - Alarms: AlarmVector.NoAlarm
15:45:37 - Connection status: False TXclient_alive: True
15:45:38 - Status: TibState.Armed
15:45:38 - Alarms: AlarmVector.NoAlarm
15:45:38 - Connection status: True TXclient_alive: True
15:45:40 - Starting TIB triggers...
15:45:40 - Enabling trigger
15:45:40 - Status: TibState.Running
15:45:40 - Alarms: AlarmVector.NoAlarm
15:45:40 - Connection status: True TXclient_alive: True
15:45:42 - Starting flashes...
15:45:46 - Checking for high voltage locked pixels...
15:46:08 - Stopping TIB...
15:46:08 - Status: TibState.Running
15:46:08 - Alarms: AlarmVector.ReadError
15:46:08 - Connection status: True TXclient_alive: True
15:46:08 - Disabling trigger
15:46:08 - Disabling PPS
15:46:09 - Status: TibState.PpsStopped
15:46:09 - Alarms: AlarmVector.ReadError
15:46:09 - Connection status: True TXclient_alive: True
15:46:09 - Closing TIB connection to camera server
15:46:15 - Status: TibState.PpsStopped
15:46:15 - Alarms: AlarmVector.ReadError
15:46:15 - Connection status: False TXclient_alive: False
15:46:15 - Run duration: 0:00:30
15:46:15 - Local camera triggers: 0
15:46:15 - Slow control triggers: 0
15:46:15 - Single photo-electron triggers: 0
15:46:15 - Calibration triggers: 11914
15:46:15 - Software triggers from UCTS: 0
15:46:15 - Pedestal triggers: 0
15:46:15 - Collected input triggers: 11914
15:46:15 - Busy triggers: 0
15:46:15 - Camera event triggers sent to clusters: 11914
15:46:16 - Checking for high voltage locked pixels...
15:46:18 - Calling method FSM.gotoReady in object FSM
15:46:46 - Checking for high voltage locked pixels...