15:27:16 - Checking for high voltage locked pixels...
15:27:28 - Resetting NMC
15:27:28 - Could not invoke the MethodCall service: BadDisconnect
15:27:46 - Checking for high voltage locked pixels...
15:28:16 - Checking for high voltage locked pixels...
15:28:46 - Checking for high voltage locked pixels...
15:29:16 - Checking for high voltage locked pixels...
15:29:46 - Checking for high voltage locked pixels...
15:30:16 - Checking for high voltage locked pixels...
15:30:46 - Checking for high voltage locked pixels...
15:31:16 - Checking for high voltage locked pixels...
15:31:31 - Starting task "Configure modules"
15:31:31 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200605/config_tower_2modules_+30V.NMC.xml
15:31:31 - Switching off high voltages in configuration
15:31:34 - Successfully configured 2 module(s)
15:31:35 - All front-end boards are programmed with firmware F55D1907
15:31:35 - All backplanes are programmed with firmware 15
15:31:35 - NMC is in state NmcState.Configured and knows of 2 drawer(s)
15:31:36 - Found PPS errors: 255 in drawer 93
15:31:36 - Finished task "Configure modules"
15:31:46 - Checking for high voltage locked pixels...
15:32:01 - Starting task "Switch HVPA voltage state"
15:32:01 - Setting HVPA current limit to 12489.75 uA
15:32:01 - Setting HVPA ramp speed to 25 V/s
15:32:01 - Switching HVPA to state Nominal
15:32:08 - Setting HVPA current limits...
15:32:09 - Finished task "Switch HVPA voltage state"
15:32:16 - Starting task "Check high voltages"
15:32:16 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
15:32:16 - Actual voltage is between 739.93 V and 885.72 V.
15:32:16 - Low voltages range between 100.00 V and 300.00 V. 
15:32:16 - Checking for high voltage locked pixels...
15:32:16 - Reference voltages range between 1013.92 V and 1147.69 V. 
15:32:17 - Maximum difference between expected and actual voltages is 800.36 V
15:32:17 - Maximum of current limits is 4969.06 uA
15:32:17 - Checking status of HVPA module in 2 drawer(s)...
15:32:17 - Checking status of HVPA channels in 2 drawer(s)...
15:32:17 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 14 channel(s)
15:32:17 - Finished task "Check high voltages"
15:32:39 - Starting task "Check high voltages"
15:32:39 - Found 0 drawer(s) in Nominal state, 2 in Low state and 0 in Wait state
15:32:40 - Actual voltage is between 1013.82 V and 1148.02 V.
15:32:40 - Low voltages range between 100.00 V and 300.00 V. 
15:32:40 - Reference voltages range between 1013.92 V and 1147.69 V. 
15:32:40 - Maximum difference between expected and actual voltages is 1047.41 V
15:32:40 - Maximum of current limits is 4969.06 uA
15:32:40 - Checking status of HVPA module in 2 drawer(s)...
15:32:40 - Checking status of HVPA channels in 2 drawer(s)...
15:32:41 - HV is stabilized in all channels.
15:32:41 - Finished task "Check high voltages"
15:32:46 - Checking for high voltage locked pixels...
15:32:49 - Stopping NMC
15:32:49 - Found PPS errors: 255 in drawer 93
15:32:50 - Starting NMC
15:32:50 - Clearing PPS error counters
15:33:05 - Calling method FSM.gotoObserving in object FSM
15:33:16 - Checking for high voltage locked pixels...
15:33:31 - Configuring UCTS
15:33:31 - Configuring TIB...
15:33:31 - Setting TIB forced mode to False
15:33:31 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:33:31 - Status: TibState.PpsStopped
15:33:31 - Alarms: AlarmVector.ReadError
15:33:31 - Connection status: False TXclient_alive: False
15:33:31 - Entering set_external_delay
15:33:31 - Setting ExternalDelayLocal to 0.000 ns
15:33:31 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:33:32 - Entering set_external_delay
15:33:32 - Setting ExternalDelayCalibration to 65.000 ns
15:33:32 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:33:32 - Entering set_external_delay
15:33:32 - Setting ExternalDelaySphe to 150.000 ns
15:33:32 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:33:32 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:33:32 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:33:32 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:33:32 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:33:32 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:33:32 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:33:32 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:33:32 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:33:32 - Status: TibState.PpsStopped
15:33:32 - Alarms: AlarmVector.ReadError
15:33:32 - Connection status: False TXclient_alive: False
15:33:32 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:33:32 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:33:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:33:32 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:33:32 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:33:32 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:33:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:33:32 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:33:32 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:33:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:33:34 - Configuring calibration box...
15:33:34 - Configuring calibration box with leds=0x40 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=120 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
15:33:37 - Connecting TIB to camera server at 10.10.4.12:222
15:33:37 - Starting TIB...
15:33:37 - Status: TibState.PpsStopped
15:33:37 - Alarms: AlarmVector.ReadError
15:33:37 - Connection status: False TXclient_alive: True
15:33:37 - Resetting run
15:33:37 - Wait for UCTS external trigger before enabling trigger...
15:33:37 - Status: TibState.Standby
15:33:37 - Alarms: AlarmVector.NoAlarm
15:33:37 - Connection status: False TXclient_alive: True
15:33:37 - Status: TibState.Standby
15:33:37 - Alarms: AlarmVector.NoAlarm
15:33:37 - Connection status: False TXclient_alive: True
15:33:38 - Status: TibState.Armed
15:33:38 - Alarms: AlarmVector.NoAlarm
15:33:38 - Connection status: True TXclient_alive: True
15:33:39 - Starting TIB triggers...
15:33:39 - Enabling trigger
15:33:39 - Status: TibState.Running
15:33:39 - Alarms: AlarmVector.NoAlarm
15:33:39 - Connection status: True TXclient_alive: True
15:33:42 - Starting flashes...
15:33:46 - Checking for high voltage locked pixels...
15:34:02 - Stopping TIB...
15:34:02 - Status: TibState.Running
15:34:02 - Alarms: AlarmVector.ReadError
15:34:02 - Connection status: True TXclient_alive: True
15:34:02 - Disabling trigger
15:34:02 - Disabling PPS
15:34:03 - Status: TibState.PpsStopped
15:34:03 - Alarms: AlarmVector.ReadError
15:34:03 - Connection status: True TXclient_alive: True
15:34:03 - Closing TIB connection to camera server
15:34:04 - Status: TibState.PpsStopped
15:34:04 - Alarms: AlarmVector.ReadError
15:34:04 - Connection status: False TXclient_alive: False
15:34:04 - Run duration: 0:00:24
15:34:04 - Local camera triggers: 0
15:34:04 - Slow control triggers: 0
15:34:04 - Single photo-electron triggers: 0
15:34:04 - Calibration triggers: 11963
15:34:04 - Software triggers from UCTS: 0
15:34:04 - Pedestal triggers: 0
15:34:04 - Collected input triggers: 11963
15:34:04 - Busy triggers: 0
15:34:04 - Camera event triggers sent to clusters: 11963
15:34:07 - Calling method FSM.gotoReady in object FSM
15:34:16 - Checking for high voltage locked pixels...