14:59:27 - Starting task "Configure modules"
14:59:27 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200526/config_tower_53modules_NoHighGain.NMC.xml
14:59:27 - Switching off high voltages in configuration
14:59:30 - Successfully configured 53 module(s)
14:59:31 - All front-end boards are programmed with firmware F55D2001
14:59:32 - All backplanes are programmed with firmware 15
14:59:37 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
14:59:37 - Checking for high voltage locked pixels...
14:59:38 - Found 0 PPS errors.
14:59:38 - Finished task "Configure modules"
14:59:47 - Starting task "Switch HVPA voltage state"
14:59:48 - Setting HVPA current limit to 12489.75 uA
15:00:05 - Setting HVPA ramp speed to 25 V/s
15:00:07 - Switching HVPA to state Nominal
15:00:07 - Checking for high voltage locked pixels...
15:00:16 - Setting HVPA current limits...
15:00:37 - Checking for high voltage locked pixels...
15:00:39 - Finished task "Switch HVPA voltage state"
15:01:07 - Checking for high voltage locked pixels...
15:01:37 - Checking for high voltage locked pixels...
15:01:53 - Starting task "Check high voltages"
15:01:54 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:01:58 - Stopping NMC
15:01:58 - Found 0 PPS errors.
15:02:01 - Starting NMC
15:02:01 - Clearing PPS error counters
15:02:02 - Actual voltage is between 945.50 V and 1166.93 V.
15:02:03 - Low voltages range between 300.00 V and 300.00 V. 
15:02:07 - Checking for high voltage locked pixels...
15:02:12 - Reference voltages range between 945.26 V and 1167.15 V. 
15:02:21 - Maximum difference between expected and actual voltages is 0.72 V
15:02:25 - Maximum of current limits is 5647.07 uA
15:02:25 - Checking status of HVPA module in 53 drawer(s)...
15:02:26 - Checking status of HVPA channels in 53 drawer(s)...
15:02:30 - HV is stabilized in all channels.
15:02:30 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200526/config_tower_53modules_NoHighGain.NMC.xml
15:02:35 - Done
15:02:35 - Finished task "Check high voltages"
15:02:37 - Checking for high voltage locked pixels...
15:03:01 - Calling method FSM.gotoObserving in object FSM
15:03:07 - Checking for high voltage locked pixels...
15:03:28 - Stopping flashes...
15:03:31 - Configuring calibration box...
15:03:31 - Configuring calibration box with leds=0x40 voltage=15.50 frequency=1000.0/1 central_current=0.0 duration=240 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
15:03:37 - Checking for high voltage locked pixels...
15:03:40 - Configuring UCTS
15:03:40 - Configuring TIB...
15:03:40 - Setting TIB forced mode to False
15:03:40 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:03:40 - Status: TibState.PpsStopped
15:03:40 - Alarms: AlarmVector.ReadError
15:03:40 - Connection status: False TXclient_alive: False
15:03:40 - Entering set_external_delay
15:03:40 - Setting ExternalDelayLocal to 0.000 ns
15:03:40 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:03:40 - Entering set_external_delay
15:03:40 - Setting ExternalDelayCalibration to 65.000 ns
15:03:40 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:03:40 - Entering set_external_delay
15:03:40 - Setting ExternalDelaySphe to 150.000 ns
15:03:40 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:03:40 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:03:40 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:03:40 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:03:40 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:03:40 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:03:40 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:03:40 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:03:40 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:03:40 - Status: TibState.PpsStopped
15:03:40 - Alarms: AlarmVector.ReadError
15:03:40 - Connection status: False TXclient_alive: False
15:03:40 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:03:40 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:03:40 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:03:40 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:03:40 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:03:40 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:03:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:03:41 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:03:41 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:03:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:03:49 - Connecting TIB to camera server at 10.10.4.12:222
15:03:49 - Starting TIB...
15:03:49 - Status: TibState.PpsStopped
15:03:49 - Alarms: AlarmVector.ReadError
15:03:49 - Connection status: False TXclient_alive: False
15:03:49 - Resetting run
15:03:49 - Wait for UCTS external trigger before enabling trigger...
15:03:49 - Status: TibState.Standby
15:03:49 - Alarms: AlarmVector.NoAlarm
15:03:49 - Connection status: False TXclient_alive: True
15:03:49 - Status: TibState.Standby
15:03:49 - Alarms: AlarmVector.NoAlarm
15:03:49 - Connection status: False TXclient_alive: True
15:03:50 - Status: TibState.Armed
15:03:50 - Alarms: AlarmVector.NoAlarm
15:03:50 - Connection status: False TXclient_alive: True
15:03:52 - Starting TIB triggers...
15:03:52 - Enabling trigger
15:03:52 - Status: TibState.Running
15:03:52 - Alarms: AlarmVector.NoAlarm
15:03:52 - Connection status: True TXclient_alive: True
15:03:57 - Starting flashes...
15:04:07 - Checking for high voltage locked pixels...
15:04:27 - Stopping TIB...
15:04:27 - Status: TibState.Running
15:04:27 - Alarms: AlarmVector.ReadError
15:04:27 - Connection status: True TXclient_alive: True
15:04:27 - Disabling trigger
15:04:27 - Disabling PPS
15:04:28 - Status: TibState.PpsStopped
15:04:28 - Alarms: AlarmVector.ReadError
15:04:28 - Connection status: True TXclient_alive: True
15:04:28 - Closing TIB connection to camera server
15:04:29 - Status: TibState.PpsStopped
15:04:29 - Alarms: AlarmVector.ReadError
15:04:29 - Connection status: False TXclient_alive: False
15:04:29 - Run duration: 0:00:36
15:04:29 - Local camera triggers: 0
15:04:29 - Slow control triggers: 0
15:04:29 - Single photo-electron triggers: 0
15:04:29 - Calibration triggers: 23947
15:04:29 - Software triggers from UCTS: 0
15:04:29 - Pedestal triggers: 0
15:04:29 - Collected input triggers: 23947
15:04:29 - Busy triggers: 0
15:04:29 - Camera event triggers sent to clusters: 23947
15:04:33 - Calling method FSM.gotoReady in object FSM
15:04:37 - Checking for high voltage locked pixels...