10:34:12 - ECC is in state EccState.Ready with status EccStatus.NoError
10:34:12 - Average temperature: 18.6 deg C
10:34:12 - Air temperature (T1-T6 and T9-T10): 18.6, 1255.0, -838.0, -838.0, -838.0, 1254.0, 1254.0, 1253.0 deg C
10:34:12 - Air differential pressure: 0.0 Pa
10:34:12 - Water temperature (T11-T12): 1253.0, -838.0 deg C
10:34:12 - Back doors are closed.
10:34:12 - Shutter is in state PartiallyOpen (error 0)
10:34:12 - Light sensors: [2.91, 3.46, 3.99, 4.34] V
10:34:12 - Humidity: 0.0 %. Water pressure: [0.0, 0.0] bar.
10:34:12 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
10:34:12 - 24 V power supply no. 1 is enabled with a current of 39.800 A.
10:34:14 - Stopping NMC
10:34:14 - Found 0 PPS errors.
10:34:16 - Starting NMC
10:34:16 - Clearing PPS error counters
10:34:28 - Starting task "Configure modules"
10:34:28 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200529/config_tower_53modules.NMC.xml
10:34:28 - Switching off high voltages in configuration
10:34:32 - Successfully configured 53 module(s)
10:34:33 - All front-end boards are programmed with firmware F55D2001
10:34:34 - All backplanes are programmed with firmware 15
10:34:34 - Checking for high voltage locked pixels...
10:34:39 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
10:34:39 - Found 0 PPS errors.
10:34:40 - Finished task "Configure modules"
10:34:41 - Starting task "Switch HVPA voltage state"
10:34:41 - Setting HVPA current limit to 12489.75 uA
10:34:59 - Setting HVPA ramp speed to 25 V/s
10:35:01 - Switching HVPA to state Nominal
10:35:04 - Checking for high voltage locked pixels...
10:35:10 - Setting HVPA current limits...
10:35:32 - Finished task "Switch HVPA voltage state"
10:35:34 - Checking for high voltage locked pixels...
10:36:04 - Checking for high voltage locked pixels...
10:36:34 - Checking for high voltage locked pixels...
10:36:48 - Starting NMC
10:36:48 - Clearing PPS error counters
10:36:53 - Starting task "Check high voltages"
10:36:54 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:37:02 - Actual voltage is between 945.50 V and 1167.54 V.
10:37:02 - Low voltages range between 300.00 V and 300.00 V. 
10:37:04 - Checking for high voltage locked pixels...
10:37:12 - Reference voltages range between 945.26 V and 1167.15 V. 
10:37:20 - Maximum difference between expected and actual voltages is 0.71 V
10:37:25 - Maximum of current limits is 5647.07 uA
10:37:25 - Checking status of HVPA module in 53 drawer(s)...
10:37:25 - Checking status of HVPA channels in 53 drawer(s)...
10:37:30 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s)
10:37:30 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200529/config_tower_53modules.NMC.xml
10:37:34 - Checking for high voltage locked pixels...
10:37:35 - Done
10:37:35 - Finished task "Check high voltages"
10:38:04 - Checking for high voltage locked pixels...
10:38:34 - Checking for high voltage locked pixels...
10:39:04 - Checking for high voltage locked pixels...
10:39:34 - Checking for high voltage locked pixels...
10:39:45 - Calling method FSM.gotoObserving in object FSM
10:40:04 - Checking for high voltage locked pixels...
10:40:13 - Configuring UCTS
10:40:13 - Configuring TIB...
10:40:13 - Setting TIB forced mode to False
10:40:13 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:40:13 - Status: TibState.PpsStopped
10:40:13 - Alarms: AlarmVector.ReadError
10:40:13 - Connection status: False TXclient_alive: False
10:40:13 - Entering set_external_delay
10:40:13 - Setting ExternalDelayLocal to 0.000 ns
10:40:13 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:40:13 - Entering set_external_delay
10:40:13 - Setting ExternalDelayCalibration to 65.000 ns
10:40:13 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:40:13 - Entering set_external_delay
10:40:13 - Setting ExternalDelaySphe to 150.000 ns
10:40:13 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:40:14 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:40:14 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:40:14 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:40:14 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:40:14 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:40:14 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:40:14 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:40:14 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:40:14 - Status: TibState.PpsStopped
10:40:14 - Alarms: AlarmVector.ReadError
10:40:14 - Connection status: False TXclient_alive: False
10:40:14 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:40:14 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:40:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:40:14 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:40:14 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:40:14 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:40:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:40:14 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:40:14 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:40:14 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:40:17 - Connecting TIB to camera server at 10.10.4.12:222
10:40:17 - Starting TIB...
10:40:17 - Status: TibState.PpsStopped
10:40:17 - Alarms: AlarmVector.ReadError
10:40:17 - Connection status: False TXclient_alive: False
10:40:17 - Resetting run
10:40:17 - Wait for UCTS external trigger before enabling trigger...
10:40:17 - Status: TibState.Standby
10:40:17 - Alarms: AlarmVector.NoAlarm
10:40:17 - Connection status: False TXclient_alive: True
10:40:17 - Status: TibState.Standby
10:40:17 - Alarms: AlarmVector.NoAlarm
10:40:17 - Connection status: False TXclient_alive: True
10:40:18 - Status: TibState.Armed
10:40:18 - Alarms: AlarmVector.NoAlarm
10:40:18 - Connection status: True TXclient_alive: True
10:40:26 - Starting TIB triggers...
10:40:26 - Enabling trigger
10:40:26 - Status: TibState.Running
10:40:26 - Alarms: AlarmVector.NoAlarm
10:40:26 - Connection status: True TXclient_alive: True
10:40:33 - Configuring calibration box...
10:40:33 - Configuring calibration box with leds=0x40 voltage=15.50 frequency=1000.0/1 central_current=0.0 duration=240 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
10:40:34 - Checking for high voltage locked pixels...
10:40:38 - Starting flashes...
10:41:04 - Checking for high voltage locked pixels...
10:41:08 - Stopping TIB...
10:41:08 - Status: TibState.Running
10:41:08 - Alarms: AlarmVector.ReadError
10:41:08 - Connection status: True TXclient_alive: True
10:41:08 - Disabling trigger
10:41:08 - Disabling PPS
10:41:09 - Status: TibState.PpsStopped
10:41:09 - Alarms: AlarmVector.ReadError
10:41:09 - Connection status: True TXclient_alive: True
10:41:09 - Closing TIB connection to camera server
10:41:10 - Status: TibState.PpsStopped
10:41:10 - Alarms: AlarmVector.ReadError
10:41:10 - Connection status: False TXclient_alive: False
10:41:10 - Run duration: 0:00:50
10:41:10 - Local camera triggers: 0
10:41:10 - Slow control triggers: 0
10:41:10 - Single photo-electron triggers: 0
10:41:10 - Calibration triggers: 23933
10:41:10 - Software triggers from UCTS: 0
10:41:10 - Pedestal triggers: 0
10:41:10 - Collected input triggers: 23933
10:41:10 - Busy triggers: 0
10:41:10 - Camera event triggers sent to clusters: 23933
10:41:14 - Calling method FSM.gotoReady in object FSM
10:41:34 - Checking for high voltage locked pixels...
10:42:04 - Checking for high voltage locked pixels...
10:42:34 - Checking for high voltage locked pixels...