10:21:12 - Setting HVPA ramp speed to 25 V/s
10:21:14 - Switching HVPA to state Nominal
10:21:23 - Setting HVPA current limits...
10:21:46 - Finished task "Switch HVPA voltage state"
10:23:35 - High voltage locked channels will be checked every 30 s
10:24:03 - Calling method FSM.gotoReady in object FSM
10:24:03 - Failed to call FSM.gotoReady: Bad statuses are present
10:24:04 - Checking for high voltage locked pixels...
10:24:05 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
10:24:05 - Module 101 has 1 pixel(s) locked (HVPA status of 0x3f)!
10:24:05 - Module 130 has 1 pixel(s) locked (HVPA status of 0x3f)!
10:24:05 - Module 146 has 1 pixel(s) locked (HVPA status of 0x7d)!
10:24:05 - Module 152 has 1 pixel(s) locked (HVPA status of 0x7b)!
10:24:06 - Module 163 has 1 pixel(s) locked (HVPA status of 0x77)!
10:24:06 - Unlocking 6 channel(s)...
10:24:06 - Resetting HVPA channel 6 of drawer 81...
10:24:06 - Resetting HVPA channel 6 of drawer 101...
10:24:06 - Resetting HVPA channel 6 of drawer 130...
10:24:07 - Resetting HVPA channel 1 of drawer 146...
10:24:07 - Resetting HVPA channel 2 of drawer 152...
10:24:07 - Resetting HVPA channel 3 of drawer 163...
10:24:15 - Calling method FSM.gotoObserving in object FSM
10:24:34 - Checking for high voltage locked pixels...
10:25:04 - Checking for high voltage locked pixels...
10:25:34 - Checking for high voltage locked pixels...
10:26:04 - Checking for high voltage locked pixels...
10:26:11 - Starting task "Check high voltages"
10:26:12 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:26:20 - Actual voltage is between 945.50 V and 1167.54 V.
10:26:20 - Low voltages range between 300.00 V and 300.00 V. 
10:26:30 - Reference voltages range between 945.26 V and 1167.15 V. 
10:26:34 - Checking for high voltage locked pixels...
10:26:38 - Maximum difference between expected and actual voltages is 0.69 V
10:26:43 - Maximum of current limits is 5647.07 uA
10:26:43 - Checking status of HVPA module in 53 drawer(s)...
10:26:44 - Checking status of HVPA channels in 53 drawer(s)...
10:26:48 - HV is stabilized in all channels.
10:26:48 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200529/config_tower_53modules_NoHighGain.NMC.xml
10:26:53 - Done
10:26:53 - Finished task "Check high voltages"
10:26:56 - Starting NMC
10:26:56 - Clearing PPS error counters
10:27:04 - Checking for high voltage locked pixels...
10:27:08 - Configuring UCTS
10:27:08 - Configuring TIB...
10:27:08 - Setting TIB forced mode to False
10:27:08 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:27:08 - Status: TibState.RunStopped
10:27:08 - Alarms: AlarmVector.NoAlarm
10:27:08 - Connection status: False TXclient_alive: False
10:27:08 - Disabling PPS
10:27:10 - Status: TibState.PpsStopped
10:27:10 - Alarms: AlarmVector.NoAlarm
10:27:10 - Connection status: False TXclient_alive: False
10:27:10 - Entering set_external_delay
10:27:10 - Setting ExternalDelayLocal to 0.000 ns
10:27:10 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:27:10 - Entering set_external_delay
10:27:10 - Setting ExternalDelayCalibration to 65.000 ns
10:27:10 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:27:10 - Entering set_external_delay
10:27:10 - Setting ExternalDelaySphe to 150.000 ns
10:27:10 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:27:10 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:27:10 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:27:10 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:27:10 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:27:10 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:27:10 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:27:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:27:10 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:27:10 - Status: TibState.PpsStopped
10:27:10 - Alarms: AlarmVector.NoAlarm
10:27:10 - Connection status: False TXclient_alive: False
10:27:10 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:27:10 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:27:10 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:27:10 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:27:10 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:27:11 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:27:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:27:11 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:27:11 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:27:11 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:27:16 - Connecting TIB to camera server at 10.10.4.12:222
10:27:16 - Starting TIB...
10:27:16 - Status: TibState.PpsStopped
10:27:16 - Alarms: AlarmVector.NoAlarm
10:27:16 - Connection status: False TXclient_alive: False
10:27:16 - Resetting run
10:27:16 - Wait for UCTS external trigger before enabling trigger...
10:27:16 - Status: TibState.Standby
10:27:16 - Alarms: AlarmVector.NoAlarm
10:27:16 - Connection status: False TXclient_alive: False
10:27:16 - Status: TibState.Standby
10:27:16 - Alarms: AlarmVector.NoAlarm
10:27:17 - Connection status: False TXclient_alive: False
10:27:18 - Status: TibState.Armed
10:27:18 - Alarms: AlarmVector.NoAlarm
10:27:18 - Connection status: True TXclient_alive: True
10:27:29 - Starting TIB triggers...
10:27:29 - Enabling trigger
10:27:29 - Status: TibState.Running
10:27:29 - Alarms: AlarmVector.NoAlarm
10:27:29 - Connection status: True TXclient_alive: True
10:27:34 - Checking for high voltage locked pixels...
10:28:01 - Configuring calibration box...
10:28:01 - Configuring calibration box with leds=0x40 voltage=15.50 frequency=1000.0/1 central_current=0.0 duration=240 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
10:28:04 - Checking for high voltage locked pixels...
10:28:11 - Starting flashes...
10:28:34 - Checking for high voltage locked pixels...
10:28:41 - Stopping TIB...
10:28:41 - Status: TibState.Running
10:28:41 - Alarms: AlarmVector.ReadError
10:28:41 - Connection status: True TXclient_alive: True
10:28:41 - Disabling trigger
10:28:41 - Disabling PPS
10:28:42 - Status: TibState.PpsStopped
10:28:42 - Alarms: AlarmVector.ReadError
10:28:42 - Connection status: True TXclient_alive: True
10:28:42 - Closing TIB connection to camera server
10:28:48 - Calling method FSM.gotoReady in object FSM
10:29:04 - Checking for high voltage locked pixels...
10:29:34 - Checking for high voltage locked pixels...
10:30:04 - Checking for high voltage locked pixels...