15:36:30 - Starting task "Configure modules"
15:36:30 - Setting L0 thresholds to 15.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20191203/l0_threshold_slope_and_offset_feb.h5
15:36:35 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200214/config_2020-02-14_15-36-30.NMC.xml
15:36:35 - Switching off high voltages in configuration
15:36:39 - Successfully configured 53 module(s)
15:36:39 - All front-end boards are programmed with firmware F55D2001
15:36:40 - All backplanes are programmed with firmware 15
15:36:45 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
15:36:46 - Found 0 PPS errors.
15:36:46 - Finished task "Configure modules"
15:36:47 - Starting task "Switch HVPA voltage state"
15:36:47 - Setting HVPA current limit to 12489.75 uA
15:36:49 - High voltage locked channels will be checked every 30 s
15:37:04 - Calling method FSM.gotoObserving in object FSM
15:37:05 - Setting HVPA ramp speed to 25 V/s
15:37:07 - Switching HVPA to state Nominal
15:37:16 - Setting HVPA current limits...
15:37:19 - Checking for high voltage locked pixels...
15:37:39 - Finished task "Switch HVPA voltage state"
15:37:49 - Starting NMC
15:37:49 - Clearing PPS error counters
15:37:52 - Checking for high voltage locked pixels...
15:37:59 - Starting task "Check high voltages"
15:38:00 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:38:02 - Stopping flashes...
15:38:08 - Actual voltage is between 944.89 V and 1167.54 V.
15:38:09 - Low voltages range between 300.00 V and 300.00 V. 
15:38:18 - Reference voltages range between 945.26 V and 1167.15 V. 
15:38:19 - Checking for high voltage locked pixels...
15:38:27 - Maximum difference between expected and actual voltages is 3.81 V
15:38:31 - Maximum of current limits is 5647.07 uA
15:38:31 - Checking status of HVPA module in 53 drawer(s)...
15:38:32 - Checking status of HVPA channels in 53 drawer(s)...
15:38:36 - HV is stabilized in all channels.
15:38:36 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200214/config_tower_53modules_nd.NMC.xml
15:38:41 - Done
15:38:42 - Finished task "Check high voltages"
15:38:49 - Checking for high voltage locked pixels...
15:38:58 - Configuring calibration box...
15:38:58 - Configuring calibration box with leds=0x40 voltage=14.75 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
15:39:00 - Starting flashes...
15:39:11 - Configuring UCTS
15:39:11 - Configuring TIB...
15:39:11 - Setting TIB forced mode to False
15:39:11 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:39:11 - Status: TibState.RunStopped
15:39:11 - Alarms: AlarmVector.NoAlarm
15:39:11 - Connection status: False
15:39:11 - Disabling PPS
15:39:13 - Status: TibState.PpsStopped
15:39:13 - Alarms: AlarmVector.NoAlarm
15:39:13 - Connection status: False
15:39:13 - Entering set_external_delay
15:39:13 - Setting ExternalDelayLocal to 0.000 ns
15:39:13 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:39:14 - Entering set_external_delay
15:39:14 - Setting ExternalDelayCalibration to 65.000 ns
15:39:14 - Writing 65.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:39:14 - Entering set_external_delay
15:39:14 - Setting ExternalDelaySphe to 150.000 ns
15:39:14 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:39:14 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:39:14 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:39:15 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:39:16 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:39:16 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:39:16 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:39:16 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:39:16 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:39:16 - Status: TibState.PpsStopped
15:39:16 - Alarms: AlarmVector.NoAlarm
15:39:16 - Connection status: False
15:39:16 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:39:16 - Writing 500 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:39:16 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:39:16 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:39:16 - Writing 500 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:39:16 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:39:16 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:39:16 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:39:16 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:39:16 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:39:19 - Checking for high voltage locked pixels...
15:39:22 - Connecting TIB to camera server at 10.10.4.12:222
15:39:22 - Starting TIB...
15:39:22 - Status: TibState.PpsStopped
15:39:22 - Alarms: AlarmVector.NoAlarm
15:39:22 - Connection status: False
15:39:22 - Resetting run
15:39:22 - Wait for UCTS external trigger before enabling trigger...
15:39:22 - Status: TibState.Standby
15:39:22 - Alarms: AlarmVector.NoAlarm
15:39:22 - Connection status: False
15:39:22 - Status: TibState.Standby
15:39:22 - Alarms: AlarmVector.NoAlarm
15:39:22 - Connection status: False
15:39:23 - Status: TibState.Armed
15:39:23 - Alarms: AlarmVector.NoAlarm
15:39:23 - Connection status: True
15:39:24 - Starting TIB triggers...
15:39:24 - Enabling trigger
15:39:24 - Status: TibState.Running
15:39:24 - Alarms: AlarmVector.NoAlarm
15:39:24 - Connection status: True
15:39:45 - Stopping TIB...
15:39:45 - Status: TibState.Running
15:39:45 - Alarms: AlarmVector.ReadError
15:39:45 - Connection status: True
15:39:45 - Disabling trigger
15:39:45 - Disabling PPS
15:39:46 - Status: TibState.PpsStopped
15:39:46 - Alarms: AlarmVector.ReadError
15:39:46 - Connection status: True
15:39:46 - Closing TIB connection to camera server
15:39:47 - Status: TibState.PpsStopped
15:39:47 - Alarms: AlarmVector.ReadError
15:39:47 - Connection status: False
15:39:47 - Run duration: 0:00:22
15:39:47 - Local camera triggers: 0
15:39:47 - Slow control triggers: 0
15:39:47 - Single photo-electron triggers: 0
15:39:47 - Calibration triggers: 21315
15:39:47 - Software triggers from UCTS: 0
15:39:47 - Pedestal triggers: 0
15:39:47 - Collected input triggers: 20449
15:39:47 - Busy triggers: 0
15:39:47 - Camera event triggers sent to clusters: 20449
15:39:49 - Checking for high voltage locked pixels...
15:39:51 - Calling method FSM.gotoReady in object FSM