15:09:33 - Starting task "Configure modules"
15:09:34 - Configuring modules with configuration /local/home/cta_test_bench/config/2020/20200128/config_tower_53modules_nd.NMC.xml
15:09:34 - Switching off high voltages in configuration
15:09:38 - Successfully configured 53 module(s)
15:09:39 - All front-end boards are programmed with firmware F55D2001
15:09:40 - All backplanes are programmed with firmware 15
15:09:45 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
15:09:46 - Found 0 PPS errors.
15:09:46 - Finished task "Configure modules"
15:09:52 - Starting task "Switch HVPA voltage state"
15:09:52 - Setting HVPA current limit to 12489.75 uA
15:09:53 - High voltage locked channels will be checked every 30 s
15:10:10 - Setting HVPA ramp speed to 25 V/s
15:10:12 - Switching HVPA to state Nominal
15:10:21 - Setting HVPA current limits...
15:10:23 - Checking for high voltage locked pixels...
15:10:44 - Finished task "Switch HVPA voltage state"
15:10:53 - Checking for high voltage locked pixels...
15:10:54 - Module 81 has 1 pixel(s) locked (HVPA status of 0x3f)!
15:10:54 - Module 130 has 1 pixel(s) locked (HVPA status of 0x3f)!
15:10:55 - Unlocking 2 channel(s)...
15:10:55 - Resetting HVPA channel 6 of drawer 81...
15:10:55 - Resetting HVPA channel 6 of drawer 130...
15:11:23 - Checking for high voltage locked pixels...
15:11:29 - Starting task "Set L0 trigger thresholds"
15:11:30 - Setting L0 thresholds to 7.0 p.e. using /local/home/cta_test_bench/data/2019/20191203/l0_threshold_slope_and_offset_feb.h5
15:11:32 - NumExpr defaulting to 4 threads.
15:11:51 - Setting L0 thresholds to 7.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20191203/l0_threshold_slope_and_offset_feb.h5
15:11:52 - Thresholds saved in configuration file /local/home/cta_test_bench/config/2020/20200205/config_2020-02-05_15-11-51.NMC.xml
15:11:52 - Finished task "Set L0 trigger thresholds"
15:11:53 - Checking for high voltage locked pixels...
15:12:22 - Starting task "Check high voltages"
15:12:23 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:12:23 - Checking for high voltage locked pixels...
15:12:31 - Actual voltage is between 945.50 V and 1167.54 V.
15:12:32 - Low voltages range between 300.00 V and 300.00 V. 
15:12:41 - Reference voltages range between 945.26 V and 1167.15 V. 
15:12:50 - Maximum difference between expected and actual voltages is 0.71 V
15:12:53 - Checking for high voltage locked pixels...
15:12:54 - Maximum of current limits is 5647.07 uA
15:12:54 - Checking status of HVPA module in 53 drawer(s)...
15:12:55 - Checking status of HVPA channels in 53 drawer(s)...
15:12:59 - HV is stabilized in all channels.
15:12:59 - Checking reference and low voltages against /local/home/cta_test_bench/config/2020/20200128/config_tower_53modules_nd.NMC.xml
15:13:04 - Done
15:13:04 - Finished task "Check high voltages"
15:13:14 - Starting NMC
15:13:14 - Clearing PPS error counters
15:13:23 - Checking for high voltage locked pixels...
15:13:53 - Checking for high voltage locked pixels...
15:14:23 - Checking for high voltage locked pixels...
15:14:26 - Calling method FSM.gotoReady in object FSM
15:14:38 - Calling method FSM.gotoObserving in object FSM
15:14:53 - Checking for high voltage locked pixels...
15:15:00 - Starting task "Mask all trigger channels"
15:15:00 - Disabling all DTC trigger channels
15:15:23 - Checking for high voltage locked pixels...
15:15:53 - Checking for high voltage locked pixels...
15:16:03 - Finished task "Set DTC trigger masks"
15:16:07 - Starting task "Set DTC trigger masks"
15:16:07 - Configuring DTC trigger masks for 53 configured module(s)
15:16:07 - Setting DTC slot 1 trigger mask to 0xf7ee
15:16:11 - Setting DTC slot 5 trigger mask to 0xfdf6
15:16:14 - Setting DTC slot 6 trigger mask to 0x0028
15:16:18 - Setting DTC slot 9 trigger mask to 0x0000
15:16:21 - Setting DTC slot 13 trigger mask to 0xdfb8
15:16:23 - Checking for high voltage locked pixels...
15:16:25 - Setting DTC slot 14 trigger mask to 0x00d0
15:16:28 - Setting DTC slot 15 trigger mask to 0x0600
15:16:32 - Setting DTC slot 19 trigger mask to 0xb786
15:16:35 - Finished task "Set DTC trigger masks"
15:16:48 - Configuring calibration box...
15:16:48 - Configuring calibration box with leds=0x40 voltage=10.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=False fiber1_out=False fiber2_out=False lemo_in=False enabled=False
15:16:52 - Starting flashes...
15:16:53 - Checking for high voltage locked pixels...
15:17:03 - Configuring UCTS
15:17:03 - Configuring TIB...
15:17:03 - Setting TIB forced mode to False
15:17:03 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:17:03 - Status: TibState.PpsStopped
15:17:03 - Alarms: AlarmVector.ReadError
15:17:03 - Connection status: False
15:17:03 - Entering set_external_delay
15:17:03 - Setting ExternalDelayLocal to 0.000 ns
15:17:03 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:17:03 - Entering set_external_delay
15:17:03 - Setting ExternalDelayCalibration to 98.000 ns
15:17:03 - Writing 98.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:17:03 - Entering set_external_delay
15:17:03 - Setting ExternalDelaySphe to 150.000 ns
15:17:03 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:17:03 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
15:17:03 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:17:03 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:17:03 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:17:03 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:17:03 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:17:03 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:17:03 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:17:03 - Status: TibState.PpsStopped
15:17:03 - Alarms: AlarmVector.ReadError
15:17:03 - Connection status: False
15:17:03 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:17:03 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:17:03 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:17:03 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:17:03 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:17:03 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:17:03 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:17:03 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:17:04 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:17:04 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:17:09 - Connecting TIB to camera server at 10.10.4.12:222
15:17:09 - Starting TIB...
15:17:09 - Status: TibState.PpsStopped
15:17:09 - Alarms: AlarmVector.ReadError
15:17:09 - Connection status: False
15:17:09 - Resetting run
15:17:09 - Wait for UCTS external trigger before enabling trigger...
15:17:09 - Status: TibState.Standby
15:17:09 - Alarms: AlarmVector.NoAlarm
15:17:09 - Connection status: False
15:17:09 - Status: TibState.Standby
15:17:09 - Alarms: AlarmVector.NoAlarm
15:17:09 - Connection status: False
15:17:10 - Status: TibState.Armed
15:17:10 - Alarms: AlarmVector.NoAlarm
15:17:10 - Connection status: True
15:17:13 - Starting TIB triggers...
15:17:13 - Enabling trigger
15:17:13 - Status: TibState.Running
15:17:13 - Alarms: AlarmVector.NoAlarm
15:17:13 - Connection status: True
15:17:23 - Checking for high voltage locked pixels...
15:17:28 - Stopping TIB...
15:17:28 - Status: TibState.Running
15:17:28 - Alarms: AlarmVector.ReadError
15:17:28 - Connection status: True
15:17:28 - Disabling trigger
15:17:28 - Disabling PPS
15:17:29 - Status: TibState.PpsStopped
15:17:29 - Alarms: AlarmVector.ReadError
15:17:29 - Connection status: True
15:17:29 - Closing TIB connection to camera server
15:17:32 - Calling method FSM.gotoReady in object FSM
15:17:34 - Status: TibState.PpsStopped
15:17:34 - Alarms: AlarmVector.ReadError
15:17:34 - Connection status: False
15:17:34 - Run duration: 0:00:18
15:17:34 - Local camera triggers: 0
15:17:34 - Slow control triggers: 0
15:17:34 - Single photo-electron triggers: 0
15:17:34 - Calibration triggers: 0
15:17:34 - Software triggers from UCTS: 0
15:17:34 - Pedestal triggers: 1730
15:17:34 - Collected input triggers: 16028
15:17:34 - Busy triggers: 0
15:17:34 - Camera event triggers sent to clusters: 16028
15:17:53 - Checking for high voltage locked pixels...
15:18:23 - Checking for high voltage locked pixels...