13:34:27 - ECC is in state EccState.Ready with status EccStatus.NoError
13:34:27 - Average temperature: 20.4 deg C
13:34:27 - Air temperature (T1-T6 and T9-T10): 20.4, 1255.0, 1254.0, -838.0, -838.0, 1254.0, -838.0, 1253.0 deg C
13:34:27 - Air differential pressure: 101.0 Pa
13:34:27 - Water temperature (T11-T12): 1253.0, -838.0 deg C
13:34:27 - Back doors are open.
13:34:27 - Shutter is in state PartiallyOpen (error 0)
13:34:27 - Light sensors: [1.85, 2.16, 2.49, 2.73] V
13:34:27 - Humidity: 17.9 %. Water pressure: [4.6, 6.06] bar.
13:34:27 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
13:34:27 - 24 V power supply no. 1 is enabled with a current of 49.400 A.
13:34:30 - Stopping NMC
13:34:30 - Found 0 PPS errors.
13:34:31 - Starting NMC
13:34:31 - Clearing PPS error counters
13:34:34 - Starting task "Check high voltages"
13:34:35 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:34:41 - Calling method FSM.gotoObserving in object FSM
13:34:42 - Checking for high voltage locked pixels...
13:34:43 - Actual voltage is between 945.50 V and 1166.93 V.
13:34:44 - Low voltages range between 300.00 V and 300.00 V. 
13:34:53 - Reference voltages range between 945.26 V and 1167.15 V. 
13:35:02 - Maximum difference between expected and actual voltages is 1.05 V
13:35:07 - Maximum of current limits is 5647.07 uA
13:35:07 - Checking status of HVPA module in 53 drawer(s)...
13:35:07 - Checking status of HVPA channels in 53 drawer(s)...
13:35:11 - HV is stabilized in all channels.
13:35:11 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20191210/config_tower_53modules_masks_delays_pattern_l1av2.NMC.xml
13:35:12 - Checking for high voltage locked pixels...
13:35:17 - Done
13:35:17 - Finished task "Check high voltages"
13:35:22 - Configuring UCTS
13:35:23 - Configuring TIB...
13:35:23 - Setting TIB forced mode to False
13:35:23 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:35:23 - Status: TibState.RunStopped
13:35:23 - Alarms: AlarmVector.NoAlarm
13:35:23 - Connection status: False
13:35:23 - Disabling PPS
13:35:25 - Status: TibState.PpsStopped
13:35:25 - Alarms: AlarmVector.NoAlarm
13:35:25 - Connection status: False
13:35:25 - Entering set_external_delay
13:35:25 - Setting ExternalDelayLocal to 0.000 ns
13:35:25 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:35:25 - Entering set_external_delay
13:35:25 - Setting ExternalDelayCalibration to 98.000 ns
13:35:25 - Writing 98.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:35:25 - Entering set_external_delay
13:35:25 - Setting ExternalDelaySphe to 150.000 ns
13:35:25 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:35:25 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
13:35:25 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:35:25 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:35:25 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:35:25 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:35:25 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:35:25 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:35:25 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:35:25 - Status: TibState.PpsStopped
13:35:25 - Alarms: AlarmVector.NoAlarm
13:35:25 - Connection status: False
13:35:25 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:35:25 - Writing 4000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:35:25 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:35:25 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:35:25 - Writing 4000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:35:25 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:35:25 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:35:25 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:35:25 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:35:25 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:35:28 - Connecting TIB to camera server at 10.10.4.12:222
13:35:28 - Starting TIB...
13:35:28 - Status: TibState.PpsStopped
13:35:28 - Alarms: AlarmVector.NoAlarm
13:35:28 - Connection status: False
13:35:28 - Resetting run
13:35:28 - Wait for UCTS external trigger before enabling trigger...
13:35:28 - Status: TibState.Standby
13:35:28 - Alarms: AlarmVector.NoAlarm
13:35:28 - Connection status: False
13:35:28 - Status: TibState.Standby
13:35:28 - Alarms: AlarmVector.NoAlarm
13:35:28 - Connection status: False
13:35:29 - Status: TibState.Armed
13:35:29 - Alarms: AlarmVector.NoAlarm
13:35:29 - Connection status: True
13:35:31 - Starting TIB triggers...
13:35:31 - Enabling trigger
13:35:31 - Status: TibState.Running
13:35:31 - Alarms: AlarmVector.NoAlarm
13:35:31 - Connection status: True
13:35:36 - Configuring calibration box...
13:35:36 - Configuring calibration box with leds=0x358 voltage=11.00 frequency=2000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
13:35:42 - Checking for high voltage locked pixels...
13:35:44 - Configuring calibration box...
13:35:44 - Configuring calibration box with leds=0x358 voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
13:35:49 - Scanning voltages
13:35:49 - Starting task "Scan voltages"
13:35:49 - Setting LED mask to 0x0
13:35:49 - Configuring calibration box with leds=0x0 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
13:35:49 - Starting flashes...
13:35:55 - Stopping flashes...
13:35:56 - Setting LED mask to 0x358
13:36:07 - Setting voltage to 8.000000 V
13:36:08 - Starting flashes...
13:36:12 - Checking for high voltage locked pixels...
13:36:14 - Stopping flashes...
13:36:25 - Setting voltage to 8.250000 V
13:36:26 - Starting flashes...
13:36:33 - Stopping flashes...
13:36:42 - Checking for high voltage locked pixels...
13:36:44 - Setting voltage to 8.500000 V
13:36:45 - Starting flashes...
13:36:51 - Stopping flashes...
13:37:02 - Setting voltage to 8.750000 V
13:37:03 - Starting flashes...
13:37:09 - Stopping flashes...
13:37:12 - Checking for high voltage locked pixels...
13:37:20 - Setting voltage to 9.000000 V
13:37:21 - Starting flashes...
13:37:27 - Stopping flashes...
13:37:38 - Setting voltage to 9.250000 V
13:37:39 - Starting flashes...
13:37:42 - Checking for high voltage locked pixels...
13:37:45 - Stopping flashes...
13:37:56 - Setting voltage to 9.500000 V
13:37:58 - Starting flashes...
13:38:04 - Stopping flashes...
13:38:12 - Checking for high voltage locked pixels...
13:38:15 - Setting voltage to 9.750000 V
13:38:16 - Starting flashes...
13:38:22 - Stopping flashes...
13:38:33 - Setting voltage to 10.000000 V
13:38:34 - Starting flashes...
13:38:40 - Stopping flashes...
13:38:42 - Checking for high voltage locked pixels...
13:38:51 - Setting voltage to 10.250000 V
13:38:52 - Starting flashes...
13:38:58 - Stopping flashes...
13:39:09 - Setting voltage to 10.500000 V
13:39:10 - Starting flashes...
13:39:12 - Checking for high voltage locked pixels...
13:39:16 - Stopping flashes...
13:39:28 - Setting voltage to 10.750000 V
13:39:29 - Starting flashes...
13:39:35 - Stopping flashes...
13:39:42 - Checking for high voltage locked pixels...
13:39:46 - Setting voltage to 11.000000 V
13:39:47 - Starting flashes...
13:39:53 - Stopping flashes...
13:40:04 - Setting voltage to 11.250000 V
13:40:05 - Starting flashes...
13:40:11 - Stopping flashes...
13:40:12 - Checking for high voltage locked pixels...
13:40:22 - Setting voltage to 11.500000 V
13:40:23 - Starting flashes...
13:40:29 - Stopping flashes...
13:40:40 - Setting voltage to 11.750000 V
13:40:42 - Starting flashes...
13:40:42 - Checking for high voltage locked pixels...
13:40:48 - Stopping flashes...
13:40:59 - Setting voltage to 12.000000 V
13:41:00 - Starting flashes...
13:41:06 - Stopping flashes...
13:41:12 - Checking for high voltage locked pixels...
13:41:17 - Setting voltage to 12.250000 V
13:41:18 - Starting flashes...
13:41:24 - Stopping flashes...
13:41:35 - Setting voltage to 12.500000 V
13:41:36 - Starting flashes...
13:41:42 - Stopping flashes...
13:41:42 - Checking for high voltage locked pixels...
13:41:53 - Setting voltage to 12.750000 V
13:41:54 - Starting flashes...
13:42:00 - Stopping flashes...
13:42:12 - Setting voltage to 13.000000 V
13:42:12 - Checking for high voltage locked pixels...
13:42:13 - Starting flashes...
13:42:19 - Stopping flashes...
13:42:30 - Setting voltage to 13.250000 V
13:42:31 - Starting flashes...
13:42:37 - Stopping flashes...
13:42:42 - Checking for high voltage locked pixels...
13:42:48 - Setting voltage to 13.500000 V
13:42:49 - Starting flashes...
13:42:55 - Stopping flashes...
13:43:06 - Setting voltage to 13.750000 V
13:43:07 - Starting flashes...
13:43:12 - Checking for high voltage locked pixels...
13:43:13 - Stopping flashes...
13:43:24 - Setting voltage to 14.000000 V
13:43:25 - Starting flashes...
13:43:32 - Stopping flashes...
13:43:42 - Checking for high voltage locked pixels...
13:43:43 - Setting voltage to 14.250000 V
13:43:44 - Starting flashes...
13:43:50 - Stopping flashes...
13:44:01 - Setting voltage to 14.500000 V
13:44:02 - Starting flashes...
13:44:08 - Stopping flashes...
13:44:12 - Checking for high voltage locked pixels...
13:44:19 - Setting voltage to 14.750000 V
13:44:20 - Starting flashes...
13:44:26 - Stopping flashes...
13:44:37 - Setting voltage to 15.000000 V
13:44:38 - Starting flashes...
13:44:42 - Checking for high voltage locked pixels...
13:44:44 - Stopping flashes...
13:44:55 - Setting voltage to 15.250000 V
13:44:57 - Starting flashes...
13:45:03 - Stopping flashes...
13:45:12 - Checking for high voltage locked pixels...
13:45:14 - Setting voltage to 15.500000 V
13:45:15 - Starting flashes...
13:45:21 - Stopping flashes...
13:45:32 - Setting voltage to 15.750000 V
13:45:33 - Starting flashes...
13:45:39 - Stopping flashes...
13:45:42 - Checking for high voltage locked pixels...
13:45:50 - Setting voltage to 16.000000 V
13:45:51 - Starting flashes...
13:45:57 - Stopping flashes...
13:45:58 - Finished task "Scan voltages"
13:46:12 - Checking for high voltage locked pixels...
13:46:25 - Stopping TIB...
13:46:25 - Status: TibState.Running
13:46:25 - Alarms: AlarmVector.ReadError
13:46:25 - Connection status: True
13:46:25 - Disabling trigger
13:46:25 - Disabling PPS
13:46:26 - Status: TibState.PpsStopped
13:46:26 - Alarms: AlarmVector.ReadError
13:46:26 - Connection status: True
13:46:26 - Closing TIB connection to camera server
13:46:28 - Calling method FSM.gotoReady in object FSM
13:46:31 - Status: TibState.PpsStopped
13:46:31 - Alarms: AlarmVector.ReadError
13:46:31 - Connection status: False
13:46:31 - Run duration: 0:10:56
13:46:31 - Local camera triggers: 0
13:46:31 - Slow control triggers: 0
13:46:31 - Single photo-electron triggers: 0
13:46:31 - Calibration triggers: 205846
13:46:31 - Software triggers from UCTS: 0
13:46:31 - Pedestal triggers: 0
13:46:31 - Collected input triggers: 205845
13:46:31 - Busy triggers: 0
13:46:31 - Camera event triggers sent to clusters: 205845