15:14:12 - ECC is in state EccState.Ready with status EccStatus.NoError
15:14:12 - Average temperature: 19.7 deg C
15:14:12 - Air temperature (T1-T6 and T9-T10): 19.7, -838.0, 1254.0, 1254.0, 1254.0, 1254.0, -838.0, 1253.0 deg C
15:14:12 - Air differential pressure: 100.0 Pa
15:14:12 - Water temperature (T11-T12): 1253.0, -838.0 deg C
15:14:12 - Back doors are open.
15:14:12 - Shutter is in state PartiallyOpen (error 0)
15:14:12 - Light sensors: [1.86, 2.17, 2.5, 2.74] V
15:14:12 - Humidity: 17.5 %. Water pressure: [4.6, 6.04] bar.
15:14:12 - Fan speeds: [0.0, 0.0, 0.0, 0.0, 0.0, 0.0] rpm
15:14:12 - 24 V power supply no. 1 is enabled with a current of 48.800 A.
15:14:23 - Starting task "Configure modules"
15:14:23 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20191128/config_tower_53modules.NMC.xml
15:14:23 - Switching off high voltages in configuration
15:14:27 - Successfully configured 53 module(s)
15:14:32 - NMC is in state NmcState.Configured and knows of 53 drawer(s)
15:14:33 - Found 0 PPS errors.
15:14:33 - Finished task "Configure modules"
15:14:34 - Starting task "Switch HVPA voltage state"
15:14:34 - Setting HVPA current limit to 12489.75 uA
15:14:47 - Stopping flashes...
15:14:52 - Setting HVPA ramp speed to 25 V/s
15:14:54 - Switching HVPA to state Nominal
15:15:03 - Setting HVPA current limits...
15:15:26 - Finished task "Switch HVPA voltage state"
15:15:52 - Starting task "Check high voltages"
15:15:52 - Found 53 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
15:16:01 - Actual voltage is between 944.89 V and 1166.93 V.
15:16:01 - Low voltages range between 300.00 V and 300.00 V. 
15:16:11 - Reference voltages range between 945.26 V and 1167.15 V. 
15:16:19 - Maximum difference between expected and actual voltages is 0.99 V
15:16:24 - Maximum of current limits is 5647.07 uA
15:16:24 - Checking status of HVPA module in 53 drawer(s)...
15:16:25 - Checking status of HVPA channels in 53 drawer(s)...
15:16:29 - HV is stabilized in all channels.
15:16:29 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20191128/config_tower_53modules.NMC.xml
15:16:34 - Done
15:16:34 - Finished task "Check high voltages"
15:16:42 - High voltage locked channels will be checked every 30 s
15:16:45 - Starting NMC
15:16:45 - Clearing PPS error counters
15:16:50 - Calling method FSM.gotoObserving in object FSM
15:17:12 - Checking for high voltage locked pixels...
15:17:26 - Configuring UCTS
15:17:26 - Configuring TIB...
15:17:26 - Setting TIB forced mode to False
15:17:26 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:17:26 - Status: TibState.Running
15:17:26 - Alarms: AlarmVector.NoAlarm
15:17:26 - Connection status: True
15:17:26 - Disabling PPS
15:17:26 - Error configuring TIB: Failed to call DisablePPS: Bad statuses are present
15:17:31 - Stopping TIB...
15:17:31 - Status: TibState.Running
15:17:31 - Alarms: AlarmVector.NoAlarm
15:17:31 - Connection status: True
15:17:31 - Disabling trigger
15:17:31 - Disabling PPS
15:17:32 - Status: TibState.PpsStopped
15:17:32 - Alarms: AlarmVector.NoAlarm
15:17:32 - Connection status: True
15:17:32 - Closing TIB connection to camera server
15:17:35 - Resetting TIB...
15:17:36 - Failed to call Reset: Bad statuses are present
15:17:38 - Configuring UCTS
15:17:38 - Configuring TIB...
15:17:38 - Setting TIB forced mode to False
15:17:38 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
15:17:38 - Status: TibState.RunStopped
15:17:38 - Alarms: AlarmVector.NoAlarm
15:17:38 - Connection status: False
15:17:38 - Disabling PPS
15:17:40 - Status: TibState.PpsStopped
15:17:40 - Alarms: AlarmVector.NoAlarm
15:17:40 - Connection status: False
15:17:40 - Entering set_external_delay
15:17:40 - Setting ExternalDelayLocal to 0.000 ns
15:17:40 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
15:17:40 - Entering set_external_delay
15:17:40 - Setting ExternalDelayCalibration to 98.000 ns
15:17:40 - Writing 98.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
15:17:41 - Entering set_external_delay
15:17:41 - Setting ExternalDelaySphe to 150.000 ns
15:17:41 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
15:17:41 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
15:17:41 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
15:17:41 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
15:17:41 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
15:17:41 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
15:17:41 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
15:17:41 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
15:17:41 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
15:17:41 - Status: TibState.PpsStopped
15:17:41 - Alarms: AlarmVector.NoAlarm
15:17:41 - Connection status: False
15:17:41 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
15:17:41 - Writing 10000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
15:17:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:17:41 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
15:17:41 - Writing 10000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
15:17:41 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
15:17:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:17:41 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
15:17:41 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
15:17:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
15:17:42 - Checking for high voltage locked pixels...
15:17:44 - Connecting TIB to camera server at 10.10.4.12:222
15:17:44 - Starting TIB...
15:17:44 - Status: TibState.PpsStopped
15:17:44 - Alarms: AlarmVector.NoAlarm
15:17:44 - Connection status: False
15:17:44 - Resetting run
15:17:44 - Wait for UCTS external trigger before enabling trigger...
15:17:44 - Status: TibState.Standby
15:17:44 - Alarms: AlarmVector.NoAlarm
15:17:44 - Connection status: False
15:17:44 - Status: TibState.Standby
15:17:44 - Alarms: AlarmVector.NoAlarm
15:17:44 - Connection status: False
15:17:45 - Status: TibState.Armed
15:17:45 - Alarms: AlarmVector.NoAlarm
15:17:45 - Connection status: True
15:17:47 - Starting TIB triggers...
15:17:47 - Enabling trigger
15:17:47 - Status: TibState.Running
15:17:47 - Alarms: AlarmVector.NoAlarm
15:17:47 - Connection status: True
15:18:04 - Configuring calibration box...
15:18:04 - Configuring calibration box with leds=0x1fff voltage=11.00 frequency=1000.0/1 central_current=0.0 duration=500 width=1 lemo_out=True fiber1_out=True fiber2_out=False lemo_in=False enabled=False
15:18:05 - Starting flashes...
15:18:12 - Checking for high voltage locked pixels...
15:18:42 - Checking for high voltage locked pixels...
15:19:00 - Stopping TIB...
15:19:00 - Status: TibState.Running
15:19:00 - Alarms: AlarmVector.ReadError
15:19:00 - Connection status: True
15:19:00 - Disabling trigger
15:19:01 - Disabling PPS
15:19:02 - Status: TibState.PpsStopped
15:19:02 - Alarms: AlarmVector.ReadError
15:19:02 - Connection status: True
15:19:02 - Closing TIB connection to camera server
15:19:05 - Status: TibState.PpsStopped
15:19:05 - Alarms: AlarmVector.ReadError
15:19:05 - Connection status: False
15:19:05 - Run duration: 0:01:16
15:19:05 - Local camera triggers: 0
15:19:05 - Slow control triggers: 0
15:19:05 - Single photo-electron triggers: 0
15:19:05 - Calibration triggers: 49974
15:19:05 - Software triggers from UCTS: 0
15:19:05 - Pedestal triggers: 0
15:19:05 - Collected input triggers: 49974
15:19:05 - Busy triggers: 0
15:19:05 - Camera event triggers sent to clusters: 49974