10:09:14 - Stopping flashes...
10:09:16 - ECC is in state EccState.Ready with status EccStatus.NoError
10:09:16 - Average temperature: 21.0 deg C
10:09:16 - Air temperature (T1-T6 and T9-T10): 22.5, 20.0, 19.9, 21.5, 21.3, 21.0, 16.6, 16.4 deg C
10:09:16 - Air differential pressure: 1.9 Pa
10:09:16 - Water temperature (T11-T12): 14.2, 13.0 deg C
10:09:16 - Back doors are closed.
10:09:16 - Shutter is in state Open (error 0)
10:09:16 - Light sensors: [0.01, 0.01, 0.0, 6.22] V
10:09:16 - Humidity: 43.4 %. Water pressure: [2.42, 2.02] bar.
10:09:16 - Fan speeds: [0.0, 0.0, 2400.0, 2280.0, 0.0, 0.0] rpm
10:09:16 - 24 V power supply no. 1 is enabled with a current of 50.500 A.
10:09:22 - Starting task "Switch HVPA voltage state"
10:09:22 - Setting HVPA current limit to 12489.75 uA
10:09:40 - Setting HVPA ramp speed to 25 V/s
10:09:43 - Switching HVPA to state Nominal
10:09:52 - Setting HVPA current limits...
10:10:15 - Finished task "Switch HVPA voltage state"
10:10:17 - High voltage locked channels will be checked every 30 s
10:10:19 - Starting task "Check high voltages"
10:10:19 - Found 54 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:10:28 - Actual voltage is between 25.01 V and 1158.39 V.
10:10:28 - Low voltages range between 300.00 V and 300.00 V. 
10:10:38 - Reference voltages range between 0.00 V and 1167.15 V. 
10:10:47 - Maximum difference between expected and actual voltages is 18.30 V
10:10:47 - Checking for high voltage locked pixels...
10:10:48 - Module 83 has 1 pixel(s) locked (HVPA status of 0x77)!
10:10:48 - Module 111 has 1 pixel(s) locked (HVPA status of 0x7d)!
10:10:48 - Module 128 has 1 pixel(s) locked (HVPA status of 0x3f)!
10:10:58 - Unlocking 3 channel(s)...
10:10:58 - Resetting HVPA channel 3 of drawer 83...
10:10:58 - Resetting HVPA channel 1 of drawer 111...
10:10:58 - Resetting HVPA channel 6 of drawer 128...
10:11:00 - Maximum of current limits is 5647.07 uA
10:11:00 - Checking status of HVPA module in 54 drawer(s)...
10:11:01 - Checking status of HVPA channels in 54 drawer(s)...
10:11:05 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 3 channel(s)
10:11:05 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190923/config_54modules.NMC.xml
10:11:10 - Done
10:11:10 - Finished task "Check high voltages"
10:11:17 - Configuring UCTS
10:11:17 - Configuring TIB...
10:11:17 - Setting TIB forced mode to False
10:11:17 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
10:11:17 - Status: TibState.RunStopped
10:11:17 - Alarms: AlarmVector.NoAlarm
10:11:17 - Connection status: False
10:11:17 - Disabling PPS
10:11:19 - Status: TibState.PpsStopped
10:11:19 - Alarms: AlarmVector.NoAlarm
10:11:19 - Connection status: False
10:11:19 - Entering set_external_delay
10:11:19 - Setting ExternalDelayLocal to 0.000 ns
10:11:19 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
10:11:19 - Entering set_external_delay
10:11:19 - Setting ExternalDelayCalibration to 50.000 ns
10:11:19 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
10:11:19 - Entering set_external_delay
10:11:19 - Setting ExternalDelaySphe to 150.000 ns
10:11:19 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
10:11:20 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
10:11:20 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
10:11:20 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
10:11:20 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
10:11:20 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
10:11:20 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
10:11:20 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
10:11:20 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
10:11:20 - Status: TibState.PpsStopped
10:11:20 - Alarms: AlarmVector.NoAlarm
10:11:20 - Connection status: False
10:11:20 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
10:11:20 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
10:11:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11:20 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
10:11:20 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
10:11:20 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
10:11:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11:20 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
10:11:20 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
10:11:20 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
10:11:20 - Checking for high voltage locked pixels...
10:11:47 - Checking for high voltage locked pixels...
10:12:17 - Checking for high voltage locked pixels...
10:12:28 - Starting task "Check high voltages"
10:12:29 - Found 54 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
10:12:37 - Actual voltage is between 945.50 V and 1166.93 V.
10:12:38 - Low voltages range between 300.00 V and 300.00 V. 
10:12:47 - Reference voltages range between 945.26 V and 1167.15 V. 
10:12:47 - Checking for high voltage locked pixels...
10:12:56 - Maximum difference between expected and actual voltages is 0.66 V
10:13:01 - Maximum of current limits is 5647.07 uA
10:13:01 - Checking status of HVPA module in 54 drawer(s)...
10:13:01 - Checking status of HVPA channels in 54 drawer(s)...
10:13:06 - HV is stabilized in all channels.
10:13:06 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190923/config_54modules.NMC.xml
10:13:11 - Done
10:13:11 - Finished task "Check high voltages"
10:13:13 - Stopping NMC
10:13:14 - Found PPS errors: 120 in drawer 63, 120 in drawer 64, 120 in drawer 65, 120 in drawer 67, 120 in drawer 78, 120 in drawer 79, 120 in drawer 80, 120 in drawer 82, 120 in drawer 83, 120 in drawer 94, 120 in drawer 95, 120 in drawer 96, 120 in drawer 97, 120 in drawer 98, 120 in drawer 100, 120 in drawer 111, 120 in drawer 112, 120 in drawer 113, 120 in drawer 114, 120 in drawer 115, 120 in drawer 116, 120 in drawer 118, 255 in drawer 128, 255 in drawer 129, 255 in drawer 130, 255 in drawer 131, 255 in drawer 132, 255 in drawer 133, 255 in drawer 134, 255 in drawer 135, 255 in drawer 136, 120 in drawer 146, 120 in drawer 147, 120 in drawer 148, 120 in drawer 149, 120 in drawer 150, 120 in drawer 151, 120 in drawer 152, 120 in drawer 153, 120 in drawer 164, 120 in drawer 166, 120 in drawer 167, 120 in drawer 168, 120 in drawer 169, 120 in drawer 170, 120 in drawer 182, 120 in drawer 183, 120 in drawer 184, 120 in drawer 186, 120 in drawer 197, 120 in drawer 198, 120 in drawer 199, 120 in drawer 200, 120 in drawer 201
10:13:16 - Starting NMC
10:13:16 - Clearing PPS error counters
10:13:19 - Checking for high voltage locked pixels...
10:13:25 - Connecting TIB to camera server at 10.10.4.12:222
10:13:25 - Starting TIB...
10:13:25 - Status: TibState.PpsStopped
10:13:25 - Alarms: AlarmVector.NoAlarm
10:13:25 - Connection status: False
10:13:25 - Resetting run
10:13:25 - Wait for UCTS external trigger before enabling trigger...
10:13:25 - Status: TibState.Standby
10:13:25 - Alarms: AlarmVector.NoAlarm
10:13:25 - Connection status: False
10:13:25 - Status: TibState.Standby
10:13:25 - Alarms: AlarmVector.NoAlarm
10:13:25 - Connection status: False
10:13:26 - Status: TibState.Armed
10:13:26 - Alarms: AlarmVector.NoAlarm
10:13:26 - Connection status: True
10:13:33 - Configuring calibration box...
10:13:33 - Configuring calibration box with leds=0x1fff voltage=12.00 frequency=1000.0/1 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=True
10:13:35 - Starting flashes...
10:13:40 - Starting TIB triggers...
10:13:40 - Enabling trigger
10:13:40 - Status: TibState.Running
10:13:40 - Alarms: AlarmVector.NoAlarm
10:13:40 - Connection status: True
10:13:43 - Status: TibState.Running ConnectionStatus: True
10:13:43 - Alarms: AlarmVector.ReadError
10:13:43 - Temperature: 37.94
10:13:43 - Local camera rate: 0.0 Hz
10:13:43 - Stereo trigger rate: 0.0 Hz
10:13:43 - SPE trigger rate: 0.0 Hz
10:13:43 - Calibration trigger rate: 1000.0 Hz
10:13:43 - Software trigger rate: 0.0 Hz
10:13:43 - Pedestal trigger rate: 0.0 Hz
10:13:43 - Collected trigger rate: 1000.0 Hz
10:13:43 - Busy rate: 0.0 Hz
10:13:43 - Camera trigger rate: 1000.0 Hz
10:13:47 - Checking for high voltage locked pixels...
10:14:01 - Stopping TIB...
10:14:01 - Status: TibState.Running
10:14:01 - Alarms: AlarmVector.ReadError
10:14:01 - Connection status: True
10:14:01 - Disabling trigger
10:14:01 - Disabling PPS
10:14:02 - Status: TibState.PpsStopped
10:14:02 - Alarms: AlarmVector.ReadError
10:14:02 - Connection status: True
10:14:02 - Closing TIB connection to camera server
10:14:12 - Status: TibState.PpsStopped
10:14:12 - Alarms: AlarmVector.ReadError
10:14:12 - Connection status: False
10:14:12 - Run duration: 0:00:35
10:14:12 - Local camera triggers: 0
10:14:12 - Slow control triggers: 0
10:14:12 - Single photo-electron triggers: 0
10:14:12 - Calibration triggers: 27659
10:14:12 - Software triggers from UCTS: 0
10:14:12 - Pedestal triggers: 0
10:14:12 - Collected input triggers: 21032
10:14:12 - Busy triggers: 0
10:14:12 - Camera event triggers sent to clusters: 21032
10:14:17 - Checking for high voltage locked pixels...