12:45 - Starting task "Configure modules" 12:45 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190801/config_61modules.NMC.xml 12:45 - Switching off high voltages in configuration 12:45 - Successfully configured 61 module(s) 12:45 - NMC is in state NmcState.Configured and knows of 61 drawer(s) 12:45 - Found PPS errors: 255 in drawer 128, 255 in drawer 129, 255 in drawer 130, 255 in drawer 131, 255 in drawer 132, 255 in drawer 133, 255 in drawer 134, 255 in drawer 135, 255 in drawer 136 12:45 - Finished task "Configure modules" 12:45 - Starting task "Switch HVPA voltage state" 12:45 - Setting HVPA current limit to 12489.75 uA 12:46 - Checking for high voltage locked pixels... 12:46 - Setting HVPA ramp speed to 25 V/s 12:46 - Switching HVPA to state Nominal 12:46 - Checking for high voltage locked pixels... 12:46 - Setting HVPA current limits... 12:47 - Checking for high voltage locked pixels... 12:47 - Module 96 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:47 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:47 - Module 113 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:47 - Module 114 has 1 pixel(s) locked (HVPA status of 0x3f)! 12:47 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:47 - Unlocking 5 channel(s)... 12:47 - Resetting HVPA channel 2 of drawer 96... 12:47 - Resetting HVPA channel 5 of drawer 98... 12:47 - Resetting HVPA channel 0 of drawer 113... 12:47 - Resetting HVPA channel 6 of drawer 114... 12:47 - Resetting HVPA channel 3 of drawer 118... 12:47 - Finished task "Check high voltages" 12:47 - Starting task "Check high voltages" 12:47 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 12:47 - Actual voltage is between 172.63 V and 1167.54 V. 12:47 - Checking for high voltage locked pixels... 12:47 - Module 96 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:47 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:47 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:47 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:47 - Module 148 has 1 pixel(s) locked (HVPA status of 0x3f)! 12:47 - Module 153 has 2 pixel(s) locked (HVPA status of 0x5e)! 12:47 - Module 166 has 2 pixel(s) locked (HVPA status of 0x5b)! 12:47 - Module 182 has 1 pixel(s) locked (HVPA status of 0x3f)! 12:47 - Unlocking 10 channel(s)... 12:47 - Resetting HVPA channel 2 of drawer 96... 12:47 - Resetting HVPA channel 5 of drawer 98... 12:47 - Resetting HVPA channel 3 of drawer 118... 12:47 - Resetting HVPA channel 2 of drawer 136... 12:47 - Resetting HVPA channel 6 of drawer 148... 12:47 - Resetting HVPA channel 0 of drawer 153... 12:47 - Resetting HVPA channel 5 of drawer 153... 12:47 - Resetting HVPA channel 2 of drawer 166... 12:47 - Resetting HVPA channel 5 of drawer 166... 12:47 - Resetting HVPA channel 6 of drawer 182... 12:47 - Low voltages range between 100.00 V and 100.00 V. 12:47 - Reference voltages range between 0.00 V and 1167.15 V. 12:47 - Maximum difference between expected and actual voltages is 843.75 V 12:47 - Maximum of current limits is 5647.07 uA 12:47 - Checking status of HVPA module in 61 drawer(s)... 12:47 - HVPA module in drawer 96 has a status of 0x7b! 12:47 - HVPA module in drawer 98 has a status of 0x5f! 12:47 - HVPA module in drawer 118 has a status of 0x77! 12:47 - HVPA module in drawer 136 has a status of 0x7b! 12:47 - HVPA module in drawer 148 has a status of 0x3f! 12:47 - HVPA module in drawer 153 has a status of 0x5e! 12:47 - HVPA module in drawer 166 has a status of 0x5b! 12:47 - HVPA module in drawer 182 has a status of 0x3f! 12:47 - Checking status of HVPA channels in 61 drawer(s)... 12:47 - HVPA channel 0 of drawer 153 has status 0x8003! 12:47 - HVPA channel 2 of drawer 96 has status 0x8003! 12:47 - HVPA channel 2 of drawer 136 has status 0x8003! 12:47 - HVPA channel 2 of drawer 166 has status 0x8007! 12:48 - HVPA channel 3 of drawer 118 has status 0x8003! 12:48 - Checking for high voltage locked pixels... 12:48 - Module 96 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:48 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:48 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:48 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:48 - Module 148 has 1 pixel(s) locked (HVPA status of 0x3f)! 12:48 - Module 153 has 2 pixel(s) locked (HVPA status of 0x5e)! 12:48 - Module 166 has 2 pixel(s) locked (HVPA status of 0x5b)! 12:48 - Module 182 has 1 pixel(s) locked (HVPA status of 0x3f)! 12:48 - Unlocking 10 channel(s)... 12:48 - Resetting HVPA channel 2 of drawer 96... 12:48 - Resetting HVPA channel 5 of drawer 98... 12:48 - Resetting HVPA channel 3 of drawer 118... 12:48 - Resetting HVPA channel 2 of drawer 136... 12:48 - Resetting HVPA channel 6 of drawer 148... 12:48 - Resetting HVPA channel 0 of drawer 153... 12:48 - Resetting HVPA channel 5 of drawer 153... 12:48 - Resetting HVPA channel 2 of drawer 166... 12:48 - Resetting HVPA channel 5 of drawer 166... 12:48 - Resetting HVPA channel 6 of drawer 182... 12:48 - HVPA channel 5 of drawer 98 has status 0x8003! 12:48 - HVPA channel 5 of drawer 153 has status 0x8003! 12:48 - HVPA channel 5 of drawer 166 has status 0x8003! 12:48 - HVPA channel 6 of drawer 148 has status 0x8003! 12:48 - HVPA channel 6 of drawer 182 has status 0x8003! 12:48 - HV is locked in 10 channel(s), was in rise default in 0 channel(s) and was still in progress in 0 channel(s) 12:48 - Resetting 10 channel(s)... 12:48 - Resetting HVPA channel 0 of drawer 153... 12:48 - Resetting HVPA channel 2 of drawer 96... 12:48 - Resetting HVPA channel 2 of drawer 136... 12:48 - Resetting HVPA channel 2 of drawer 166... 12:48 - Resetting HVPA channel 3 of drawer 118... 12:48 - Resetting HVPA channel 5 of drawer 98... 12:48 - Resetting HVPA channel 5 of drawer 153... 12:48 - Resetting HVPA channel 5 of drawer 166... 12:48 - Resetting HVPA channel 6 of drawer 148... 12:48 - Resetting HVPA channel 6 of drawer 182... 12:48 - Checking for high voltage locked pixels... 12:48 - Module 96 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:48 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:48 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:48 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:48 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:48 - Module 166 has 2 pixel(s) locked (HVPA status of 0x5b)! 12:48 - Unlocking 7 channel(s)... 12:48 - Resetting HVPA channel 2 of drawer 96... 12:48 - Resetting HVPA channel 5 of drawer 98... 12:48 - Resetting HVPA channel 3 of drawer 118... 12:48 - Resetting HVPA channel 2 of drawer 136... 12:48 - Resetting HVPA channel 0 of drawer 153... 12:48 - Resetting HVPA channel 2 of drawer 166... 12:48 - Resetting HVPA channel 5 of drawer 166... 12:48 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190801/config_61modules.NMC.xml 12:48 - Reference voltage of channel 5 in drawer #98: expected 1016.77, read 0.00 12:48 - Reference voltage of channel 3 in drawer #118: expected 1056.16, read 0.00 12:48 - Reference voltage of channel 2 in drawer #136: expected 1021.77, read 0.00 12:48 - Reference voltage of channel 0 in drawer #153: expected 1003.90, read 0.00 12:48 - Reference voltage of channel 2 in drawer #166: expected 1000.52, read 0.00 12:48 - Reference voltage of channel 5 in drawer #166: expected 1011.71, read 0.00 12:48 - Done 12:48 - Finished task "Check high voltages" 12:49 - Checking for high voltage locked pixels... 12:49 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:49 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:49 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:49 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:49 - Module 166 has 2 pixel(s) locked (HVPA status of 0x5b)! 12:49 - Unlocking 6 channel(s)... 12:49 - Resetting HVPA channel 5 of drawer 98... 12:49 - Resetting HVPA channel 3 of drawer 118... 12:49 - Resetting HVPA channel 2 of drawer 136... 12:49 - Resetting HVPA channel 0 of drawer 153... 12:49 - Resetting HVPA channel 2 of drawer 166... 12:49 - Resetting HVPA channel 5 of drawer 166... 12:49 - Checking for high voltage locked pixels... 12:49 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:49 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:49 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:49 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:49 - Module 166 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:49 - Unlocking 5 channel(s)... 12:49 - Resetting HVPA channel 5 of drawer 98... 12:49 - Resetting HVPA channel 3 of drawer 118... 12:49 - Resetting HVPA channel 2 of drawer 136... 12:49 - Resetting HVPA channel 0 of drawer 153... 12:49 - Resetting HVPA channel 5 of drawer 166... 12:50 - Checking for high voltage locked pixels... 12:50 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:50 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:50 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:50 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:50 - Module 166 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:50 - Unlocking 5 channel(s)... 12:50 - Resetting HVPA channel 5 of drawer 98... 12:50 - Resetting HVPA channel 3 of drawer 118... 12:50 - Resetting HVPA channel 2 of drawer 136... 12:50 - Resetting HVPA channel 0 of drawer 153... 12:50 - Resetting HVPA channel 5 of drawer 166... 12:50 - Checking for high voltage locked pixels... 12:50 - Module 98 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:50 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:50 - Module 136 has 1 pixel(s) locked (HVPA status of 0x7b)! 12:50 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:50 - Module 166 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:50 - Unlocking 5 channel(s)... 12:50 - Resetting HVPA channel 5 of drawer 98... 12:50 - Resetting HVPA channel 3 of drawer 118... 12:50 - Resetting HVPA channel 2 of drawer 136... 12:50 - Resetting HVPA channel 0 of drawer 153... 12:50 - Resetting HVPA channel 5 of drawer 166... 12:51 - Checking for high voltage locked pixels... 12:51 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:51 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:51 - Module 166 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:51 - Unlocking 3 channel(s)... 12:51 - Resetting HVPA channel 3 of drawer 118... 12:51 - Resetting HVPA channel 0 of drawer 153... 12:51 - Resetting HVPA channel 5 of drawer 166... 12:51 - Checking for high voltage locked pixels... 12:51 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:51 - Module 153 has 1 pixel(s) locked (HVPA status of 0x7e)! 12:51 - Module 166 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:51 - Unlocking 3 channel(s)... 12:51 - Resetting HVPA channel 3 of drawer 118... 12:51 - Resetting HVPA channel 0 of drawer 153... 12:51 - Resetting HVPA channel 5 of drawer 166... 12:52 - Checking for high voltage locked pixels... 12:52 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:52 - Module 166 has 1 pixel(s) locked (HVPA status of 0x5f)! 12:52 - Unlocking 2 channel(s)... 12:52 - Resetting HVPA channel 3 of drawer 118... 12:52 - Resetting HVPA channel 5 of drawer 166... 12:52 - Checking for high voltage locked pixels... 12:52 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:52 - Unlocking 1 channel(s)... 12:52 - Resetting HVPA channel 3 of drawer 118... 12:53 - Checking for high voltage locked pixels... 12:53 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:53 - Unlocking 1 channel(s)... 12:53 - Resetting HVPA channel 3 of drawer 118... 12:53 - Checking for high voltage locked pixels... 12:53 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:53 - Unlocking 1 channel(s)... 12:53 - Resetting HVPA channel 3 of drawer 118... 12:54 - Checking for high voltage locked pixels... 12:54 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:54 - Unlocking 1 channel(s)... 12:54 - Resetting HVPA channel 3 of drawer 118... 12:54 - Starting task "Check high voltages" 12:54 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 12:54 - Actual voltage is between 56.73 V and 1167.54 V. 12:54 - Low voltages range between 100.00 V and 100.00 V. 12:54 - Checking for high voltage locked pixels... 12:54 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:54 - Unlocking 1 channel(s)... 12:54 - Resetting HVPA channel 3 of drawer 118... 12:54 - Reference voltages range between 0.00 V and 1167.15 V. 12:54 - Maximum difference between expected and actual voltages is 73.20 V 12:54 - Maximum of current limits is 12489.75 uA 12:54 - Checking status of HVPA module in 61 drawer(s)... 12:54 - HVPA module in drawer 118 has a status of 0x77! 12:54 - Checking status of HVPA channels in 61 drawer(s)... 12:54 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 2 channel(s) 12:54 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190801/config_61modules.NMC.xml 12:54 - Reference voltage of channel 3 in drawer #118: expected 1056.16, read 0.00 12:55 - Checking for high voltage locked pixels... 12:55 - Done 12:55 - Finished task "Check high voltages" 12:55 - Checking for high voltage locked pixels... 12:56 - Checking for high voltage locked pixels... 12:56 - Module 118 has 1 pixel(s) locked (HVPA status of 0x77)! 12:56 - Unlocking 1 channel(s)... 12:56 - Resetting HVPA channel 3 of drawer 118... 12:56 - Checking for high voltage locked pixels... 12:56 - Starting task "Check high voltages" 12:56 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 12:56 - Actual voltage is between 945.50 V and 1167.54 V. 12:56 - Low voltages range between 100.00 V and 100.00 V. 12:57 - Checking for high voltage locked pixels... 12:57 - Reference voltages range between 945.26 V and 1167.15 V. 12:57 - Starting NMC 12:57 - Clearing PPS error counters 12:57 - Maximum difference between expected and actual voltages is 0.69 V 12:57 - Maximum of current limits is 12489.75 uA 12:57 - Checking status of HVPA module in 61 drawer(s)... 12:57 - Checking status of HVPA channels in 61 drawer(s)... 12:57 - Configuring UCTS 12:57 - Configuring TIB... 12:57 - Setting TIB forced mode to False 12:57 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v 12:57 - Status: TibState.PpsStopped 12:57 - Alarms: AlarmVector.ReadError 12:57 - Connection status: False 12:57 - Entering set_external_delay 12:57 - Setting ExternalDelayLocal to 0.000 ns 12:57 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v 12:57 - Entering set_external_delay 12:57 - Setting ExternalDelayCalibration to 50.000 ns 12:57 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v 12:57 - Entering set_external_delay 12:57 - Setting ExternalDelaySphe to 150.000 ns 12:57 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v 12:57 - Setting TIB trigger mode to 0x78 = TriggerMask.SlowControl|Pedestal|Software|SPhE 12:57 - Writing 120 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v 12:57 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v 12:57 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v 12:57 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v 12:57 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v 12:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v 12:57 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v 12:57 - Status: TibState.PpsStopped 12:57 - Alarms: AlarmVector.ReadError 12:57 - Connection status: False 12:57 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v 12:57 - Writing 500 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v 12:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v 12:57 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v 12:57 - Writing 500 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v 12:57 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v 12:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v 12:57 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v 12:57 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v 12:57 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v 12:57 - HV is stabilized in all channels. 12:57 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190801/config_61modules.NMC.xml 12:57 - Done 12:57 - Finished task "Check high voltages" 12:57 - Connecting TIB to camera server at 10.10.4.12:222 12:57 - Starting TIB... 12:57 - Status: TibState.PpsStopped 12:57 - Alarms: AlarmVector.ReadError 12:57 - Connection status: False 12:57 - Resetting run 12:57 - Wait for UCTS external trigger before enabling trigger... 12:57 - Status: TibState.Standby 12:57 - Alarms: AlarmVector.NoAlarm 12:57 - Connection status: False 12:57 - Status: TibState.Standby 12:57 - Alarms: AlarmVector.NoAlarm 12:57 - Connection status: False 12:57 - Status: TibState.Armed 12:57 - Alarms: AlarmVector.NoAlarm 12:57 - Connection status: True 12:57 - Checking for high voltage locked pixels... 12:57 - Starting TIB triggers... 12:57 - Enabling trigger 12:57 - Status: TibState.Running 12:57 - Alarms: AlarmVector.NoAlarm 12:57 - Connection status: True 2019-08-06 12:57:38,942 Creating OPC UA client of TIB at opc.tcp://10.10.4.64:48010 2019-08-06 12:57:38,949 Configuring calibration box with leds=0x318 voltage=10.00 frequency=2000/1 central_current=0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False 2019-08-06 12:57:38,949 Calling method NectarCAM.CalibrationBox.Configure in object NectarCAM.CalibrationBox 2019-08-06 12:57:39,029 Moving XY table to position 0: module 79 2019-08-06 12:57:39,041 Module 79 is located at (X=-34.4 cm, Y=19.8 cm) in camera coordinates 2019-08-06 12:57:39,041 Module 79 is located at (X=118.4 cm, Y=113.8 cm) in XY table coordinates 2019-08-06 12:57:39,042 Moving XY table to position (Xtable=118.4 cm, Ytable=113.8 cm) 2019-08-06 12:57:39,042 Selecting XY table position: 118.4, 113.8 2019-08-06 12:57:39,045 Moving to next XY table position 2019-08-06 12:57:39,047 Waiting for XY table to be busy... 2019-08-06 12:57:39,940 XY table busy state changed to: True 2019-08-06 12:57:39,940 XY table parking state changed to: False 2019-08-06 12:57:39,942 XY table IS busy 2019-08-06 12:57:39,942 Waiting for XY table to be idle... 2019-08-06 12:57:51,940 XY table busy state changed to: False 2019-08-06 12:57:51,942 XY table is NOT busy 2019-08-06 12:57:51,946 Current position: (X=118.36 cm, Y=113.84 cm) in XY table coordinates 2019-08-06 12:57:51,949 Distance between expected and actual positions: 0.01 cm 2019-08-06 12:57:54,952 Starting SPE flasher 2019-08-06 12:57:54,952 Starting flashes... 2019-08-06 12:57:54,952 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 12:58:16,022 Stopping SPE flasher 2019-08-06 12:58:16,022 Stopping flashes... 2019-08-06 12:58:16,022 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 12:58:17,073 Triggering TIB by slow control 2019-08-06 12:58:17,073 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 12:58:17,076 Moving XY table to position 1: module 81 2019-08-06 12:58:17,087 Module 81 is located at (X=-34.4 cm, Y=-6.6 cm) in camera coordinates 2019-08-06 12:58:17,088 Module 81 is located at (X=118.4 cm, Y=87.4 cm) in XY table coordinates 2019-08-06 12:58:17,088 Moving XY table to position (Xtable=118.4 cm, Ytable=87.4 cm) 2019-08-06 12:58:17,088 Selecting XY table position: 118.4, 87.4 2019-08-06 12:58:17,092 Moving to next XY table position 2019-08-06 12:58:17,094 Waiting for XY table to be busy... 2019-08-06 12:58:17,942 XY table busy state changed to: True 2019-08-06 12:58:17,945 XY table IS busy 2019-08-06 12:58:17,945 Waiting for XY table to be idle... 2019-08-06 12:58:34,943 XY table busy state changed to: False 2019-08-06 12:58:34,945 XY table is NOT busy 2019-08-06 12:58:34,949 Current position: (X=118.37 cm, Y=87.39 cm) in XY table coordinates 2019-08-06 12:58:34,953 Distance between expected and actual positions: 0.00 cm 2019-08-06 12:58:37,956 Starting SPE flasher 2019-08-06 12:58:37,957 Starting flashes... 2019-08-06 12:58:37,957 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 12:58:59,028 Stopping SPE flasher 2019-08-06 12:58:59,028 Stopping flashes... 2019-08-06 12:58:59,028 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 12:59:00,079 Triggering TIB by slow control 2019-08-06 12:59:00,079 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 12:59:00,082 Moving XY table to position 2: module 83 2019-08-06 12:59:00,093 Module 83 is located at (X=-34.4 cm, Y=-33.1 cm) in camera coordinates 2019-08-06 12:59:00,093 Module 83 is located at (X=118.4 cm, Y=60.9 cm) in XY table coordinates 2019-08-06 12:59:00,093 Moving XY table to position (Xtable=118.4 cm, Ytable=60.9 cm) 2019-08-06 12:59:00,093 Selecting XY table position: 118.4, 60.9 2019-08-06 12:59:00,097 Moving to next XY table position 2019-08-06 12:59:00,099 Waiting for XY table to be busy... 2019-08-06 12:59:00,945 XY table busy state changed to: True 2019-08-06 12:59:00,947 XY table IS busy 2019-08-06 12:59:00,947 Waiting for XY table to be idle... 2019-08-06 12:59:17,945 XY table busy state changed to: False 2019-08-06 12:59:17,947 XY table is NOT busy 2019-08-06 12:59:17,951 Current position: (X=118.37 cm, Y=60.93 cm) in XY table coordinates 2019-08-06 12:59:17,955 Distance between expected and actual positions: 0.00 cm 2019-08-06 12:59:20,959 Starting SPE flasher 2019-08-06 12:59:20,959 Starting flashes... 2019-08-06 12:59:20,959 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 12:59:42,029 Stopping SPE flasher 2019-08-06 12:59:42,029 Stopping flashes... 2019-08-06 12:59:42,029 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 12:59:43,080 Triggering TIB by slow control 2019-08-06 12:59:43,080 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 12:59:43,084 Moving XY table to position 3: module 118 2019-08-06 12:59:43,095 Module 118 is located at (X=-11.5 cm, Y=-46.3 cm) in camera coordinates 2019-08-06 12:59:43,096 Module 118 is located at (X=95.5 cm, Y=47.7 cm) in XY table coordinates 2019-08-06 12:59:43,096 Moving XY table to position (Xtable=95.5 cm, Ytable=47.7 cm) 2019-08-06 12:59:43,096 Selecting XY table position: 95.5, 47.7 2019-08-06 12:59:43,100 Moving to next XY table position 2019-08-06 12:59:43,102 Waiting for XY table to be busy... 2019-08-06 12:59:43,949 XY table busy state changed to: True 2019-08-06 12:59:43,952 XY table IS busy 2019-08-06 12:59:43,952 Waiting for XY table to be idle... 2019-08-06 13:00:03,950 XY table busy state changed to: False 2019-08-06 13:00:03,953 XY table is NOT busy 2019-08-06 13:00:03,957 Current position: (X=95.45 cm, Y=47.69 cm) in XY table coordinates 2019-08-06 13:00:03,961 Distance between expected and actual positions: 0.00 cm 2019-08-06 13:00:06,963 Starting SPE flasher 2019-08-06 13:00:06,963 Starting flashes... 2019-08-06 13:00:06,963 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:00:28,032 Stopping SPE flasher 2019-08-06 13:00:28,032 Stopping flashes... 2019-08-06 13:00:28,032 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:00:29,083 Triggering TIB by slow control 2019-08-06 13:00:29,083 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:00:29,086 Moving XY table to position 4: module 116 2019-08-06 13:00:29,098 Module 116 is located at (X=-11.5 cm, Y=-19.8 cm) in camera coordinates 2019-08-06 13:00:29,099 Module 116 is located at (X=95.5 cm, Y=74.2 cm) in XY table coordinates 2019-08-06 13:00:29,099 Moving XY table to position (Xtable=95.5 cm, Ytable=74.2 cm) 2019-08-06 13:00:29,099 Selecting XY table position: 95.5, 74.2 2019-08-06 13:00:29,103 Moving to next XY table position 2019-08-06 13:00:29,105 Waiting for XY table to be busy... 2019-08-06 13:00:29,953 XY table busy state changed to: True 2019-08-06 13:00:29,955 XY table IS busy 2019-08-06 13:00:29,955 Waiting for XY table to be idle... 2019-08-06 13:00:46,954 XY table busy state changed to: False 2019-08-06 13:00:46,957 XY table is NOT busy 2019-08-06 13:00:46,961 Current position: (X=95.46 cm, Y=74.15 cm) in XY table coordinates 2019-08-06 13:00:46,965 Distance between expected and actual positions: 0.01 cm 2019-08-06 13:00:49,968 Starting SPE flasher 2019-08-06 13:00:49,968 Starting flashes... 2019-08-06 13:00:49,968 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:01:11,038 Stopping SPE flasher 2019-08-06 13:01:11,039 Stopping flashes... 2019-08-06 13:01:11,039 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:01:12,090 Triggering TIB by slow control 2019-08-06 13:01:12,090 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:01:12,093 Moving XY table to position 5: module 114 2019-08-06 13:01:12,105 Module 114 is located at (X=-11.5 cm, Y=6.6 cm) in camera coordinates 2019-08-06 13:01:12,106 Module 114 is located at (X=95.5 cm, Y=100.6 cm) in XY table coordinates 2019-08-06 13:01:12,106 Moving XY table to position (Xtable=95.5 cm, Ytable=100.6 cm) 2019-08-06 13:01:12,106 Selecting XY table position: 95.5, 100.6 2019-08-06 13:01:12,110 Moving to next XY table position 2019-08-06 13:01:12,112 Waiting for XY table to be busy... 2019-08-06 13:01:12,957 XY table busy state changed to: True 2019-08-06 13:01:12,959 XY table IS busy 2019-08-06 13:01:12,959 Waiting for XY table to be idle... 2019-08-06 13:01:29,958 XY table busy state changed to: False 2019-08-06 13:01:29,960 XY table is NOT busy 2019-08-06 13:01:29,964 Current position: (X=95.46 cm, Y=100.61 cm) in XY table coordinates 2019-08-06 13:01:29,967 Distance between expected and actual positions: 0.01 cm 2019-08-06 13:01:32,970 Starting SPE flasher 2019-08-06 13:01:32,970 Starting flashes... 2019-08-06 13:01:32,970 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:01:54,041 Stopping SPE flasher 2019-08-06 13:01:54,041 Stopping flashes... 2019-08-06 13:01:54,042 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:01:55,092 Triggering TIB by slow control 2019-08-06 13:01:55,093 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:01:55,096 Moving XY table to position 6: module 112 2019-08-06 13:01:55,107 Module 112 is located at (X=-11.5 cm, Y=33.1 cm) in camera coordinates 2019-08-06 13:01:55,108 Module 112 is located at (X=95.5 cm, Y=127.1 cm) in XY table coordinates 2019-08-06 13:01:55,108 Moving XY table to position (Xtable=95.5 cm, Ytable=127.1 cm) 2019-08-06 13:01:55,108 Selecting XY table position: 95.5, 127.1 2019-08-06 13:01:55,112 Moving to next XY table position 2019-08-06 13:01:55,113 Waiting for XY table to be busy... 2019-08-06 13:01:55,958 XY table busy state changed to: True 2019-08-06 13:01:55,960 XY table IS busy 2019-08-06 13:01:55,960 Waiting for XY table to be idle... 2019-08-06 13:02:12,959 XY table busy state changed to: False 2019-08-06 13:02:12,961 XY table is NOT busy 2019-08-06 13:02:12,965 Current position: (X=95.46 cm, Y=127.07 cm) in XY table coordinates 2019-08-06 13:02:12,969 Distance between expected and actual positions: 0.00 cm 2019-08-06 13:02:15,971 Starting SPE flasher 2019-08-06 13:02:15,971 Starting flashes... 2019-08-06 13:02:15,971 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:02:37,042 Stopping SPE flasher 2019-08-06 13:02:37,042 Stopping flashes... 2019-08-06 13:02:37,042 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:02:38,093 Triggering TIB by slow control 2019-08-06 13:02:38,093 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:02:38,096 Moving XY table to position 7: module 146 2019-08-06 13:02:38,107 Module 146 is located at (X=11.5 cm, Y=46.3 cm) in camera coordinates 2019-08-06 13:02:38,108 Module 146 is located at (X=72.5 cm, Y=140.3 cm) in XY table coordinates 2019-08-06 13:02:38,108 Moving XY table to position (Xtable=72.5 cm, Ytable=140.3 cm) 2019-08-06 13:02:38,108 Selecting XY table position: 72.5, 140.3 2019-08-06 13:02:38,112 Moving to next XY table position 2019-08-06 13:02:38,114 Waiting for XY table to be busy... 2019-08-06 13:02:38,963 XY table busy state changed to: True 2019-08-06 13:02:38,965 XY table IS busy 2019-08-06 13:02:38,965 Waiting for XY table to be idle... 2019-08-06 13:02:58,966 XY table busy state changed to: False 2019-08-06 13:02:58,968 XY table is NOT busy 2019-08-06 13:02:58,972 Current position: (X=72.54 cm, Y=140.29 cm) in XY table coordinates 2019-08-06 13:02:58,977 Distance between expected and actual positions: 0.01 cm 2019-08-06 13:03:01,979 Starting SPE flasher 2019-08-06 13:03:01,979 Starting flashes... 2019-08-06 13:03:01,979 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:03:23,049 Stopping SPE flasher 2019-08-06 13:03:23,049 Stopping flashes... 2019-08-06 13:03:23,049 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:03:24,101 Triggering TIB by slow control 2019-08-06 13:03:24,101 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:03:24,104 Moving XY table to position 8: module 148 2019-08-06 13:03:24,115 Module 148 is located at (X=11.5 cm, Y=19.8 cm) in camera coordinates 2019-08-06 13:03:24,115 Module 148 is located at (X=72.5 cm, Y=113.8 cm) in XY table coordinates 2019-08-06 13:03:24,115 Moving XY table to position (Xtable=72.5 cm, Ytable=113.8 cm) 2019-08-06 13:03:24,115 Selecting XY table position: 72.5, 113.8 2019-08-06 13:03:24,119 Moving to next XY table position 2019-08-06 13:03:24,121 Waiting for XY table to be busy... 2019-08-06 13:03:24,967 XY table busy state changed to: True 2019-08-06 13:03:24,969 XY table IS busy 2019-08-06 13:03:24,969 Waiting for XY table to be idle... 2019-08-06 13:03:41,969 XY table busy state changed to: False 2019-08-06 13:03:41,972 XY table is NOT busy 2019-08-06 13:03:41,976 Current position: (X=72.54 cm, Y=113.85 cm) in XY table coordinates 2019-08-06 13:03:41,979 Distance between expected and actual positions: 0.01 cm 2019-08-06 13:03:44,982 Starting SPE flasher 2019-08-06 13:03:44,982 Starting flashes... 2019-08-06 13:03:44,982 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:04:06,053 Stopping SPE flasher 2019-08-06 13:04:06,053 Stopping flashes... 2019-08-06 13:04:06,053 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:04:07,104 Triggering TIB by slow control 2019-08-06 13:04:07,104 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:04:07,108 Moving XY table to position 9: module 150 2019-08-06 13:04:07,119 Module 150 is located at (X=11.5 cm, Y=-6.6 cm) in camera coordinates 2019-08-06 13:04:07,119 Module 150 is located at (X=72.5 cm, Y=87.4 cm) in XY table coordinates 2019-08-06 13:04:07,120 Moving XY table to position (Xtable=72.5 cm, Ytable=87.4 cm) 2019-08-06 13:04:07,120 Selecting XY table position: 72.5, 87.4 2019-08-06 13:04:07,123 Moving to next XY table position 2019-08-06 13:04:07,125 Waiting for XY table to be busy... 2019-08-06 13:04:07,971 XY table busy state changed to: True 2019-08-06 13:04:07,974 XY table IS busy 2019-08-06 13:04:07,974 Waiting for XY table to be idle... 2019-08-06 13:04:24,974 XY table busy state changed to: False 2019-08-06 13:04:24,977 XY table is NOT busy 2019-08-06 13:04:24,980 Current position: (X=72.54 cm, Y=87.39 cm) in XY table coordinates 2019-08-06 13:04:24,984 Distance between expected and actual positions: 0.00 cm 2019-08-06 13:04:27,987 Starting SPE flasher 2019-08-06 13:04:27,987 Starting flashes... 2019-08-06 13:04:27,987 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:04:49,057 Stopping SPE flasher 2019-08-06 13:04:49,057 Stopping flashes... 2019-08-06 13:04:49,057 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:04:50,108 Triggering TIB by slow control 2019-08-06 13:04:50,108 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:04:50,111 Moving XY table to position 10: module 152 2019-08-06 13:04:50,123 Module 152 is located at (X=11.5 cm, Y=-33.1 cm) in camera coordinates 2019-08-06 13:04:50,123 Module 152 is located at (X=72.5 cm, Y=60.9 cm) in XY table coordinates 2019-08-06 13:04:50,123 Moving XY table to position (Xtable=72.5 cm, Ytable=60.9 cm) 2019-08-06 13:04:50,123 Selecting XY table position: 72.5, 60.9 2019-08-06 13:04:50,127 Moving to next XY table position 2019-08-06 13:04:50,129 Waiting for XY table to be busy... 2019-08-06 13:04:50,977 XY table busy state changed to: True 2019-08-06 13:04:50,980 XY table IS busy 2019-08-06 13:04:50,980 Waiting for XY table to be idle... 2019-08-06 13:05:07,978 XY table busy state changed to: False 2019-08-06 13:05:07,980 XY table is NOT busy 2019-08-06 13:05:07,984 Current position: (X=72.54 cm, Y=60.93 cm) in XY table coordinates 2019-08-06 13:05:07,988 Distance between expected and actual positions: 0.00 cm 2019-08-06 13:05:10,990 Starting SPE flasher 2019-08-06 13:05:10,990 Starting flashes... 2019-08-06 13:05:10,990 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:05:32,060 Stopping SPE flasher 2019-08-06 13:05:32,060 Stopping flashes... 2019-08-06 13:05:32,060 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:05:33,111 Triggering TIB by slow control 2019-08-06 13:05:33,111 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:05:33,114 Moving XY table to position 11: module 185 2019-08-06 13:05:33,126 Module 185 is located at (X=34.4 cm, Y=-19.8 cm) in camera coordinates 2019-08-06 13:05:33,126 Module 185 is located at (X=49.6 cm, Y=74.2 cm) in XY table coordinates 2019-08-06 13:05:33,126 Moving XY table to position (Xtable=49.6 cm, Ytable=74.2 cm) 2019-08-06 13:05:33,126 Selecting XY table position: 49.6, 74.2 2019-08-06 13:05:33,130 Moving to next XY table position 2019-08-06 13:05:33,132 Waiting for XY table to be busy... 2019-08-06 13:05:33,979 XY table busy state changed to: True 2019-08-06 13:05:33,982 XY table IS busy 2019-08-06 13:05:33,982 Waiting for XY table to be idle... 2019-08-06 13:05:53,983 XY table busy state changed to: False 2019-08-06 13:05:53,985 XY table is NOT busy 2019-08-06 13:05:53,989 Current position: (X=49.63 cm, Y=74.14 cm) in XY table coordinates 2019-08-06 13:05:53,993 Distance between expected and actual positions: 0.01 cm 2019-08-06 13:05:56,995 Starting SPE flasher 2019-08-06 13:05:56,995 Starting flashes... 2019-08-06 13:05:56,996 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:06:18,066 Stopping SPE flasher 2019-08-06 13:06:18,067 Stopping flashes... 2019-08-06 13:06:18,067 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:06:19,117 Triggering TIB by slow control 2019-08-06 13:06:19,117 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:06:19,120 Moving XY table to position 12: module 183 2019-08-06 13:06:19,131 Module 183 is located at (X=34.4 cm, Y=6.6 cm) in camera coordinates 2019-08-06 13:06:19,132 Module 183 is located at (X=49.6 cm, Y=100.6 cm) in XY table coordinates 2019-08-06 13:06:19,132 Moving XY table to position (Xtable=49.6 cm, Ytable=100.6 cm) 2019-08-06 13:06:19,132 Selecting XY table position: 49.6, 100.6 2019-08-06 13:06:19,136 Moving to next XY table position 2019-08-06 13:06:19,137 Waiting for XY table to be busy... 2019-08-06 13:06:19,985 XY table busy state changed to: True 2019-08-06 13:06:19,988 XY table IS busy 2019-08-06 13:06:19,988 Waiting for XY table to be idle... 2019-08-06 13:06:36,985 XY table busy state changed to: False 2019-08-06 13:06:36,987 XY table is NOT busy 2019-08-06 13:06:36,992 Current position: (X=49.63 cm, Y=100.61 cm) in XY table coordinates 2019-08-06 13:06:36,995 Distance between expected and actual positions: 0.01 cm 2019-08-06 13:06:39,998 Starting SPE flasher 2019-08-06 13:06:39,998 Starting flashes... 2019-08-06 13:06:39,998 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:07:01,069 Stopping SPE flasher 2019-08-06 13:07:01,069 Stopping flashes... 2019-08-06 13:07:01,069 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:07:02,120 Triggering TIB by slow control 2019-08-06 13:07:02,120 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:07:02,123 Moving XY table to position 13: module 181 2019-08-06 13:07:02,157 Module 181 is located at (X=34.4 cm, Y=33.1 cm) in camera coordinates 2019-08-06 13:07:02,164 Module 181 is located at (X=49.6 cm, Y=127.1 cm) in XY table coordinates 2019-08-06 13:07:02,169 Moving XY table to position (Xtable=49.6 cm, Ytable=127.1 cm) 2019-08-06 13:07:02,170 Selecting XY table position: 49.6, 127.1 2019-08-06 13:07:02,185 Moving to next XY table position 2019-08-06 13:07:02,189 Waiting for XY table to be busy... 2019-08-06 13:07:02,989 XY table busy state changed to: True 2019-08-06 13:07:02,991 XY table IS busy 2019-08-06 13:07:02,991 Waiting for XY table to be idle... 2019-08-06 13:07:19,989 XY table busy state changed to: False 2019-08-06 13:07:19,992 XY table is NOT busy 2019-08-06 13:07:19,995 Current position: (X=49.63 cm, Y=127.07 cm) in XY table coordinates 2019-08-06 13:07:19,999 Distance between expected and actual positions: 0.00 cm 2019-08-06 13:07:23,000 Starting SPE flasher 2019-08-06 13:07:23,001 Starting flashes... 2019-08-06 13:07:23,001 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox 2019-08-06 13:07:44,069 Stopping SPE flasher 2019-08-06 13:07:44,069 Stopping flashes... 2019-08-06 13:07:44,069 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox 2019-08-06 13:07:45,120 Triggering TIB by slow control 2019-08-06 13:07:45,121 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB 2019-08-06 13:07:45,124 Moving white target to parking position 2019-08-06 13:07:45,126 Waiting for parked position... 2019-08-06 13:07:45,992 XY table busy state changed to: True 2019-08-06 13:08:17,996 XY table busy state changed to: False 2019-08-06 13:08:17,996 XY table parking state changed to: True 2019-08-06 13:08:17,998 XY table IS parked 12:58 - Checking for high voltage locked pixels... 12:58 - Checking for high voltage locked pixels... 12:59 - Checking for high voltage locked pixels... 12:59 - Checking for high voltage locked pixels... 13:00 - Checking for high voltage locked pixels... 13:00 - Checking for high voltage locked pixels... 13:01 - Checking for high voltage locked pixels... 13:01 - Checking for high voltage locked pixels... 13:02 - Checking for high voltage locked pixels... 13:02 - Checking for high voltage locked pixels... 13:03 - Checking for high voltage locked pixels... 13:03 - Checking for high voltage locked pixels... 13:04 - Checking for high voltage locked pixels... 13:04 - Checking for high voltage locked pixels... 13:05 - Checking for high voltage locked pixels... 13:05 - Checking for high voltage locked pixels... 13:06 - Checking for high voltage locked pixels... 13:06 - Checking for high voltage locked pixels... 13:06 - Starting task "Check high voltages" 13:06 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 13:06 - Actual voltage is between 945.50 V and 1167.54 V. 13:06 - Low voltages range between 100.00 V and 100.00 V. 13:07 - Checking for high voltage locked pixels... 13:07 - Reference voltages range between 945.26 V and 1167.15 V. 13:07 - Maximum difference between expected and actual voltages is 0.70 V 13:07 - Maximum of current limits is 12489.75 uA 13:07 - Checking status of HVPA module in 61 drawer(s)... 13:07 - Checking status of HVPA channels in 61 drawer(s)... 13:07 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 1 channel(s) 13:07 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190801/config_61modules.NMC.xml 13:07 - Checking for high voltage locked pixels... 13:07 - Done 13:07 - Finished task "Check high voltages" 13:07 - Stopping TIB... 13:07 - Status: TibState.Running 13:07 - Alarms: AlarmVector.ReadError 13:07 - Connection status: True 13:07 - Disabling trigger 13:07 - Disabling PPS 13:07 - Status: TibState.PpsStopped 13:07 - Alarms: AlarmVector.ReadError 13:07 - Connection status: True 13:07 - Closing TIB connection to camera server 13:07 - Status: TibState.PpsStopped 13:07 - Alarms: AlarmVector.ReadError 13:07 - Connection status: False 13:07 - Run duration: 0:10:15 13:07 - Local camera triggers: 0 13:07 - Slow control triggers: 14 13:07 - Single photo-electron triggers: 589955 13:07 - Calibration triggers: 614701 13:07 - Software triggers from UCTS: 0 13:07 - Pedestal triggers: 307311 13:07 - Collected input triggers: 894929 13:07 - Busy triggers: 4216 13:07 - Camera event triggers sent to clusters: 890713