09:09 - Starting task "Check high voltages"
09:09 - Found 0 drawer(s) in Nominal state, 0 in Low state and 61 in Wait state
09:10 - Actual voltage is between 140.30 V and 173.24 V.
09:10 - Low voltages range between 100.00 V and 100.00 V. 
09:10 - Reference voltages range between 945.26 V and 1167.15 V. 
09:10 - Maximum difference between expected and actual voltages is 164.09 V
09:10 - Maximum of current limits is 5647.07 uA
09:10 - Checking status of HVPA module in 61 drawer(s)...
09:10 - Checking status of HVPA channels in 61 drawer(s)...
09:10 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 427 channel(s)
09:10 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190731/config_61modules.NMC.xml
09:10 - Done
09:10 - Finished task "Check high voltages"
13:51 - Stopping NMC
13:51 - ("NmcError: Failed to call 'Stop': status Bad statuses are present, code 0x80020000", 2147614720)
13:51 - NMC is in state NmcState.Ready and knows of 0 drawer(s)
13:51 - Found 0 PPS errors.
13:51 - Starting task "Configure modules"
13:51 - Setting L0 thresholds to 7.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
13:51 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190801/config_2019-08-01_13-51-19.NMC.xml
13:51 - Switching off high voltages in configuration
13:51 - Successfully configured 61 module(s)
13:51 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
13:51 - Found PPS errors: 255 in drawer 128, 255 in drawer 129, 255 in drawer 130, 255 in drawer 131, 255 in drawer 132, 255 in drawer 133, 255 in drawer 134, 255 in drawer 135, 255 in drawer 136
13:51 - Finished task "Configure modules"
13:51 - Starting task "Set L0 trigger thresholds"
13:51 - Setting L0 thresholds to 15.0 p.e.
13:52 - Setting L0 thresholds to 15.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
13:52 - Thresholds saved in configuration file /local/home/cta_test_bench/config/2019/20190801/config_2019-08-01_13-52-06.NMC.xml
13:52 - Finished task "Set L0 trigger thresholds"
13:53 - Starting task "Switch HVPA voltage state"
13:53 - Setting HVPA current limit to 12489.75 uA
13:54 - Setting HVPA ramp speed to 25 V/s
13:54 - Switching HVPA to state Nominal
13:54 - Setting HVPA current limits...
13:54 - Finished task "Switch HVPA voltage state"
13:55 - High voltage locked channels will be checked every 30 s
13:55 - Starting task "Check high voltages"
13:55 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:55 - Actual voltage is between 21.35 V and 1166.93 V.
13:55 - Low voltages range between 100.00 V and 100.00 V. 
13:55 - Reference voltages range between 0.00 V and 1167.15 V. 
13:55 - Checking for high voltage locked pixels...
13:55 - Module 83 has 1 pixel(s) locked (HVPA status of 0x77)!
13:55 - Module 111 has 1 pixel(s) locked (HVPA status of 0x7d)!
13:55 - Unlocking 2 channel(s)...
13:55 - Resetting HVPA channel 3 of drawer 83...
13:55 - Resetting HVPA channel 1 of drawer 111...
13:55 - Maximum difference between expected and actual voltages is 12.20 V
13:55 - Maximum of current limits is 5647.07 uA
13:55 - Checking status of HVPA module in 61 drawer(s)...
13:55 - Checking status of HVPA channels in 61 drawer(s)...
13:55 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 3 channel(s)
13:55 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190801/config_61modules_1of7.NMC.xml
13:55 - Done
13:55 - Finished task "Check high voltages"
13:56 - Checking for high voltage locked pixels...
13:56 - Starting task "Check high voltages"
13:56 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:56 - Actual voltage is between 945.50 V and 1167.54 V.
13:56 - Low voltages range between 100.00 V and 100.00 V. 
13:56 - Reference voltages range between 945.26 V and 1167.15 V. 
13:56 - Checking for high voltage locked pixels...
13:56 - Maximum difference between expected and actual voltages is 0.70 V
13:56 - Maximum of current limits is 5647.07 uA
13:56 - Checking status of HVPA module in 61 drawer(s)...
13:56 - Checking status of HVPA channels in 61 drawer(s)...
13:56 - HV is stabilized in all channels.
13:56 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190801/config_61modules_1of7.NMC.xml
13:56 - Done
13:56 - Finished task "Check high voltages"
13:57 - Checking for high voltage locked pixels...
13:57 - Checking for high voltage locked pixels...
13:58 - Checking for high voltage locked pixels...
13:58 - Starting NMC
13:58 - Clearing PPS error counters
13:58 - Configuring UCTS
13:58 - Configuring TIB...
13:58 - Setting TIB forced mode to False
13:58 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:58 - Status: TibState.PpsStopped
13:58 - Alarms: AlarmVector.ReadError
13:58 - Connection status: False
13:58 - Entering set_external_delay
13:58 - Setting ExternalDelayLocal to 0.000 ns
13:58 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:58 - Entering set_external_delay
13:58 - Setting ExternalDelayCalibration to 50.000 ns
13:58 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:58 - Entering set_external_delay
13:58 - Setting ExternalDelaySphe to 150.000 ns
13:58 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:58 - Setting TIB trigger mode to 0x51 = TriggerMask.SlowControl|Software|Mono
13:58 - Writing 81 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:58 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:58 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:58 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:58 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:58 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:58 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:58 - Status: TibState.PpsStopped
13:58 - Alarms: AlarmVector.ReadError
13:58 - Connection status: False
13:58 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:58 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:58 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:58 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:58 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:58 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:58 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:58 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:58 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:58 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:58 - Connecting TIB to camera server at 10.10.4.12:222
13:58 - Starting TIB...
13:58 - Status: TibState.PpsStopped
13:58 - Alarms: AlarmVector.ReadError
13:58 - Connection status: False
13:58 - Resetting run
13:58 - Wait for UCTS external trigger before enabling trigger...
13:58 - Status: TibState.Standby
13:58 - Alarms: AlarmVector.NoAlarm
13:58 - Connection status: False
13:58 - Status: TibState.Standby
13:58 - Alarms: AlarmVector.NoAlarm
13:58 - Connection status: False
13:58 - Status: TibState.Armed
13:58 - Alarms: AlarmVector.NoAlarm
13:58 - Connection status: True
13:58 - Checking for high voltage locked pixels...
13:58 - Starting TIB triggers...
13:58 - Enabling trigger
13:58 - Status: TibState.Running
13:58 - Alarms: AlarmVector.NoAlarm
13:58 - Connection status: True
13:59 - Checking for high voltage locked pixels...
13:59 - Checking for high voltage locked pixels...
14:00 - Checking for high voltage locked pixels...
14:00 - Checking for high voltage locked pixels...
14:00 - Stopping TIB...
14:00 - Status: TibState.Running
14:00 - Alarms: AlarmVector.ReadError
14:00 - Connection status: True
14:00 - Disabling trigger
14:00 - Disabling PPS
14:00 - Status: TibState.PpsStopped
14:00 - Alarms: AlarmVector.ReadError
14:00 - Connection status: True
14:00 - Closing TIB connection to camera server
14:00 - Status: TibState.PpsStopped
14:00 - Alarms: AlarmVector.ReadError
14:00 - Connection status: False
14:00 - Run duration: 0:02:11
14:00 - Local camera triggers: 0
14:00 - Slow control triggers: 0
14:00 - Single photo-electron triggers: 0
14:00 - Calibration triggers: 0
14:00 - Software triggers from UCTS: 0
14:00 - Pedestal triggers: 0
14:00 - Collected input triggers: 139953
14:00 - Busy triggers: 1137
14:00 - Camera event triggers sent to clusters: 138816
14:00 - Stopping NMC
14:00 - Found 0 PPS errors.
14:01 - Checking for high voltage locked pixels...