17:00 - Starting task "Powering modules..."
17:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:00 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
17:00 - Finished task "Powering modules..."
17:00 - ECC is in state EccState.Ready with status EccStatus.NoError
17:00 - Average temperature: 31.7 deg C
17:00 - Air temperature (T1-T6 and T9-T10): 32.8, 30.8, 31.7, 31.5, 31.7, 32.4, 32.3, 32.4 deg C
17:00 - Air differential pressure: 2.0 Pa
17:00 - Water temperature (T11-T12): 32.6, 32.6 deg C
17:00 - Back doors are open.
17:00 - Shutter is in state Open (error 0)
17:00 - Light sensors: [0.01, 0.01, 0.01, 7.17] V
17:00 - Humidity: 35.9 %. Water pressure: [0.1, 0.1] bar.
17:00 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
17:00 - 24 V power supply no. 1 is enabled with a current of 57.900 A.
17:00 - Scanning interface p4p1 for non configured modules...
17:00 - Found 61 MAC address(es)
17:00 - Starting task "Configure modules"
17:00 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
17:00 - Switching off high voltages in configuration
17:00 - Successfully configured 61 module(s)
17:00 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
17:00 - Found 0 PPS errors.
17:01 - Finished task "Configure modules"
17:01 - Starting task "Switch HVPA voltage state"
17:01 - Setting HVPA current limit to 12489.75 uA
17:01 - High voltage locked channels will be checked every 30 s
17:01 - Setting HVPA ramp speed to 25 V/s
17:01 - Switching HVPA to state Nominal
17:01 - Checking for high voltage locked pixels...
17:01 - Setting HVPA current limits...
17:02 - Finished task "Switch HVPA voltage state"
17:02 - Checking for high voltage locked pixels...
17:02 - Starting task "Check high voltages"
17:02 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
17:02 - Actual voltage is between 944.89 V and 1167.54 V.
17:02 - Low voltages range between 100.00 V and 100.00 V. 
17:02 - Reference voltages range between 945.26 V and 1167.15 V. 
17:02 - Checking for high voltage locked pixels...
17:02 - Maximum difference between expected and actual voltages is 0.70 V
17:02 - Starting NMC
17:02 - Clearing PPS error counters
17:02 - Maximum of current limits is 5647.07 uA
17:02 - Checking status of HVPA module in 61 drawer(s)...
17:02 - Checking status of HVPA channels in 61 drawer(s)...
17:02 - HV is stabilized in all channels.
17:02 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
17:02 - Configuring UCTS
17:02 - Configuring TIB...
17:02 - Setting TIB forced mode to False
17:02 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
17:02 - Status: TibState.PpsStopped
17:02 - Alarms: AlarmVector.ReadError
17:02 - Connection status: False
17:02 - Entering set_external_delay
17:02 - Setting ExternalDelayLocal to 0.000 ns
17:02 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
17:02 - Entering set_external_delay
17:02 - Setting ExternalDelayCalibration to 50.000 ns
17:02 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
17:02 - Entering set_external_delay
17:02 - Setting ExternalDelaySphe to 150.000 ns
17:02 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
17:02 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
17:02 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
17:02 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
17:02 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
17:02 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
17:02 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
17:02 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
17:02 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
17:02 - Status: TibState.PpsStopped
17:02 - Alarms: AlarmVector.ReadError
17:02 - Connection status: False
17:02 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
17:02 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
17:02 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:02 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
17:02 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
17:02 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
17:02 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:02 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
17:02 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
17:02 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
17:02 - Connecting TIB to camera server at 10.10.4.12:222
17:02 - Starting TIB...
17:02 - Status: TibState.PpsStopped
17:02 - Alarms: AlarmVector.ReadError
17:02 - Connection status: False
17:02 - Resetting run
17:02 - Wait for UCTS external trigger before enabling trigger...
17:02 - Status: TibState.Standby
17:02 - Alarms: AlarmVector.NoAlarm
17:02 - Connection status: False
17:02 - Status: TibState.Standby
17:02 - Alarms: AlarmVector.NoAlarm
17:02 - Connection status: False
17:03 - Status: TibState.Armed
17:03 - Alarms: AlarmVector.NoAlarm
17:03 - Connection status: True
17:03 - Starting TIB triggers...
17:03 - Enabling trigger
17:03 - Status: TibState.Running
17:03 - Alarms: AlarmVector.NoAlarm
17:03 - Connection status: True
17:03 - Done
17:03 - Finished task "Check high voltages"
17:03 - Configuring calibration box...
17:03 - Configuring calibration box with leds=0x358 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=600 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
17:03 - Starting flashes...
17:03 - Checking for high voltage locked pixels...
17:03 - Checking for high voltage locked pixels...
17:04 - Checking for high voltage locked pixels...
17:04 - Stopping TIB...
17:04 - Status: TibState.Running
17:04 - Alarms: AlarmVector.ReadError
17:04 - Connection status: True
17:04 - Disabling trigger
17:04 - Disabling PPS
17:04 - Status: TibState.PpsStopped
17:04 - Alarms: AlarmVector.ReadError
17:04 - Connection status: True
17:04 - Closing TIB connection to camera server
17:04 - Status: TibState.PpsStopped
17:04 - Alarms: AlarmVector.ReadError
17:04 - Connection status: False
17:04 - Run duration: 0:01:35
17:04 - Local camera triggers: 0
17:04 - Slow control triggers: 0
17:04 - Single photo-electron triggers: 0
17:04 - Calibration triggers: 59987
17:04 - Software triggers from UCTS: 0
17:04 - Pedestal triggers: 0
17:04 - Collected input triggers: 59987
17:04 - Busy triggers: 0
17:04 - Camera event triggers sent to clusters: 59987
17:04 - Checking for high voltage locked pixels...