16:31 - Starting task "Powering modules..."
16:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:31 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:32 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:32 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
16:32 - Finished task "Powering modules..."
16:32 - ECC is in state EccState.Ready with status EccStatus.NoError
16:32 - Average temperature: 31.3 deg C
16:32 - Air temperature (T1-T6 and T9-T10): 32.3, 30.4, 31.2, 31.0, 31.2, 32.0, 32.0, 31.9 deg C
16:32 - Air differential pressure: 2.2 Pa
16:32 - Water temperature (T11-T12): 32.2, 32.2 deg C
16:32 - Back doors are open.
16:32 - Shutter is in state Open (error 0)
16:32 - Light sensors: [0.01, 0.01, 0.01, 7.13] V
16:32 - Humidity: 36.7 %. Water pressure: [0.1, 0.1] bar.
16:32 - Fan speeds: [0.0, 0.0, 2280.0, 2280.0, 0.0, 0.0] rpm
16:32 - 24 V power supply no. 1 is enabled with a current of 58.700 A.
16:32 - Scanning interface p4p1 for non configured modules...
16:32 - Found 11 MAC address(es)
16:32 - Starting task "Configure modules"
16:32 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
16:32 - Switching off high voltages in configuration
16:32 - Successfully configured 61 module(s)
16:32 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
16:32 - Found 0 PPS errors.
16:32 - Finished task "Configure modules"
16:32 - High voltage locked channels will be checked every 30 s
16:32 - Starting task "Switch HVPA voltage state"
16:32 - Setting HVPA current limit to 12489.75 uA
16:33 - Setting HVPA ramp speed to 25 V/s
16:33 - Checking for high voltage locked pixels...
16:33 - Switching HVPA to state Nominal
16:33 - Setting HVPA current limits...
16:33 - Checking for high voltage locked pixels...
16:33 - Module 66 has 1 pixel(s) locked (HVPA status of 0x7e)!
16:33 - Module 111 has 1 pixel(s) locked (HVPA status of 0x7d)!
16:33 - Unlocking 2 channel(s)...
16:33 - Resetting HVPA channel 0 of drawer 66...
16:33 - Resetting HVPA channel 1 of drawer 111...
16:33 - Finished task "Switch HVPA voltage state"
16:34 - Starting task "Check high voltages"
16:34 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:34 - Checking for high voltage locked pixels...
16:34 - Module 66 has 1 pixel(s) locked (HVPA status of 0x7e)!
16:34 - Unlocking 1 channel(s)...
16:34 - Resetting HVPA channel 0 of drawer 66...
16:34 - Actual voltage is between 53.68 V and 1167.54 V.
16:34 - Low voltages range between 100.00 V and 100.00 V. 
16:34 - Reference voltages range between 945.26 V and 1167.15 V. 
16:34 - Maximum difference between expected and actual voltages is 516.18 V
16:34 - Checking for high voltage locked pixels...
16:34 - Maximum of current limits is 5647.07 uA
16:34 - Checking status of HVPA module in 61 drawer(s)...
16:34 - Checking status of HVPA channels in 61 drawer(s)...
16:34 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 2 channel(s)
16:34 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
16:34 - Done
16:34 - Finished task "Check high voltages"
16:35 - Starting task "Check high voltages"
16:35 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:35 - Actual voltage is between 945.50 V and 1168.15 V.
16:35 - Checking for high voltage locked pixels...
16:35 - Low voltages range between 100.00 V and 100.00 V. 
16:35 - Reference voltages range between 945.26 V and 1167.15 V. 
16:35 - Maximum difference between expected and actual voltages is 0.72 V
16:35 - Maximum of current limits is 5647.07 uA
16:35 - Checking status of HVPA module in 61 drawer(s)...
16:35 - Checking status of HVPA channels in 61 drawer(s)...
16:35 - Checking for high voltage locked pixels...
16:35 - HV is stabilized in all channels.
16:35 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
16:35 - Starting NMC
16:35 - Clearing PPS error counters
16:35 - Done
16:35 - Finished task "Check high voltages"
16:36 - Checking for high voltage locked pixels...
16:36 - Configuring UCTS
16:36 - Configuring TIB...
16:36 - Setting TIB forced mode to False
16:36 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:36 - Status: TibState.PpsStopped
16:36 - Alarms: AlarmVector.ReadError
16:36 - Connection status: False
16:36 - Entering set_external_delay
16:36 - Setting ExternalDelayLocal to 0.000 ns
16:36 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:36 - Entering set_external_delay
16:36 - Setting ExternalDelayCalibration to 50.000 ns
16:36 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:36 - Entering set_external_delay
16:36 - Setting ExternalDelaySphe to 150.000 ns
16:36 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:36 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
16:36 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:36 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:36 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:36 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:36 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:36 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:36 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:36 - Status: TibState.PpsStopped
16:36 - Alarms: AlarmVector.ReadError
16:36 - Connection status: False
16:36 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:36 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:36 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:36 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:36 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:36 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:36 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:36 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:36 - Connecting TIB to camera server at 10.10.4.12:222
16:36 - Starting TIB...
16:36 - Status: TibState.PpsStopped
16:36 - Alarms: AlarmVector.ReadError
16:36 - Connection status: False
16:36 - Resetting run
16:36 - Wait for UCTS external trigger before enabling trigger...
16:36 - Status: TibState.Standby
16:36 - Alarms: AlarmVector.NoAlarm
16:36 - Connection status: False
16:36 - Status: TibState.Standby
16:36 - Alarms: AlarmVector.NoAlarm
16:36 - Connection status: False
16:36 - Status: TibState.Armed
16:36 - Alarms: AlarmVector.NoAlarm
16:36 - Connection status: True
16:36 - Starting TIB triggers...
16:36 - Enabling trigger
16:36 - Status: TibState.Running
16:36 - Alarms: AlarmVector.NoAlarm
16:36 - Connection status: True
16:36 - Configuring calibration box...
16:36 - Configuring calibration box with leds=0x40 voltage=8.00 frequency=1000.0/1 central_current=0.0 duration=600 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
16:36 - Starting flashes...
16:36 - Checking for high voltage locked pixels...
16:37 - Checking for high voltage locked pixels...
16:37 - Checking for high voltage locked pixels...
16:37 - Stopping TIB...
16:37 - Status: TibState.Running
16:37 - Alarms: AlarmVector.ReadError
16:37 - Connection status: True
16:37 - Disabling trigger
16:37 - Disabling PPS
16:37 - Status: TibState.PpsStopped
16:37 - Alarms: AlarmVector.ReadError
16:37 - Connection status: True
16:37 - Closing TIB connection to camera server
16:37 - Status: TibState.PpsStopped
16:37 - Alarms: AlarmVector.ReadError
16:37 - Connection status: False
16:37 - Run duration: 0:01:15
16:37 - Local camera triggers: 0
16:37 - Slow control triggers: 0
16:37 - Single photo-electron triggers: 0
16:37 - Calibration triggers: 59924
16:37 - Software triggers from UCTS: 0
16:37 - Pedestal triggers: 0
16:37 - Collected input triggers: 59924
16:37 - Busy triggers: 0
16:37 - Camera event triggers sent to clusters: 59924
16:37 - Stopping NMC
16:37 - Found 0 PPS errors.
16:38 - Starting task "Switch HVPA voltage state"
16:38 - Setting HVPA current limit to 12489.75 uA
16:38 - Stopped periodic check of locked high voltages
16:38 - Setting HVPA ramp speed to 500 V/s
16:38 - Switching HVPA to state Wait
16:38 - Setting HVPA current limits...
16:39 - Finished task "Switch HVPA voltage state"
16:39 - Starting task "Check high voltages"
16:39 - Found 0 drawer(s) in Nominal state, 0 in Low state and 61 in Wait state
16:39 - Actual voltage is between 301.95 V and 306.22 V.
16:39 - Low voltages range between 100.00 V and 100.00 V. 
16:39 - Reference voltages range between 945.26 V and 1167.15 V. 
16:39 - Maximum difference between expected and actual voltages is 218.38 V
16:39 - Maximum of current limits is 5647.07 uA
16:39 - Checking status of HVPA module in 61 drawer(s)...
16:39 - Checking status of HVPA channels in 61 drawer(s)...
16:39 - Resetting NMC
16:39 - Failed to read 'Hvpa.Hvpa6.Status': No targets are given
16:39 - Finished task "Check high voltages"
16:39 - Starting task "Powering modules..."
16:39 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.57
16:39 - Finished task "Powering modules..."