14:27 - Starting task "Powering modules..."
14:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:27 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:28 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
14:28 - Finished task "Powering modules..."
14:28 - ECC is in state EccState.Ready with status EccStatus.NoError
14:28 - Average temperature: 29.4 deg C
14:28 - Air temperature (T1-T6 and T9-T10): 30.4, 28.7, 29.4, 29.2, 29.4, 30.4, 30.3, 30.2 deg C
14:28 - Air differential pressure: 2.0 Pa
14:28 - Water temperature (T11-T12): 30.4, 30.3 deg C
14:28 - Back doors are open.
14:28 - Shutter is in state Open (error 0)
14:28 - Light sensors: [0.01, 0.01, 0.01, 6.95] V
14:28 - Humidity: 39.7 %. Water pressure: [0.1, 0.1] bar.
14:28 - Fan speeds: [0.0, 0.0, 2280.0, 2160.0, 0.0, 0.0] rpm
14:28 - 24 V power supply no. 1 is enabled with a current of 57.800 A.
14:28 - ECC is in state EccState.Ready with status EccStatus.NoError
14:28 - Average temperature: 29.4 deg C
14:28 - Air temperature (T1-T6 and T9-T10): 30.4, 28.7, 29.4, 29.2, 29.4, 30.4, 30.3, 30.2 deg C
14:28 - Air differential pressure: 2.0 Pa
14:28 - Water temperature (T11-T12): 30.4, 30.3 deg C
14:28 - Back doors are open.
14:28 - Shutter is in state Open (error 0)
14:28 - Light sensors: [0.01, 0.01, 0.01, 6.95] V
14:28 - Humidity: 39.7 %. Water pressure: [0.1, 0.1] bar.
14:28 - Fan speeds: [0.0, 0.0, 2520.0, 2400.0, 0.0, 0.0] rpm
14:28 - 24 V power supply no. 1 is enabled with a current of 57.700 A.
14:28 - Scanning interface p4p1 for non configured modules...
14:28 - Found 61 MAC address(es)
14:28 - Starting task "Configure modules"
14:28 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
14:28 - Switching off high voltages in configuration
14:28 - Successfully configured 61 module(s)
14:28 - High voltage locked channels will be checked every 30 s
14:28 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
14:28 - Found 0 PPS errors.
14:28 - Finished task "Configure modules"
14:28 - Starting task "Switch HVPA voltage state"
14:28 - Setting HVPA current limit to 12489.75 uA
14:28 - Checking for high voltage locked pixels...
14:28 - Setting HVPA ramp speed to 25 V/s
14:28 - Switching HVPA to state Nominal
14:29 - Setting HVPA current limits...
14:29 - Checking for high voltage locked pixels...
14:29 - Module 66 has 1 pixel(s) locked (HVPA status of 0x7e)!
14:29 - Module 128 has 1 pixel(s) locked (HVPA status of 0x3f)!
14:29 - Unlocking 2 channel(s)...
14:29 - Resetting HVPA channel 0 of drawer 66...
14:29 - Resetting HVPA channel 6 of drawer 128...
14:29 - Finished task "Switch HVPA voltage state"
14:29 - Checking for high voltage locked pixels...
14:30 - Starting task "Check high voltages"
14:30 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
14:30 - Actual voltage is between 945.50 V and 1168.15 V.
14:30 - Low voltages range between 100.00 V and 100.00 V. 
14:30 - Checking for high voltage locked pixels...
14:30 - Reference voltages range between 945.26 V and 1167.15 V. 
14:30 - Maximum difference between expected and actual voltages is 0.66 V
14:30 - Maximum of current limits is 5647.07 uA
14:30 - Checking status of HVPA module in 61 drawer(s)...
14:30 - Checking status of HVPA channels in 61 drawer(s)...
14:30 - HV is stabilized in all channels.
14:30 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
14:30 - Checking for high voltage locked pixels...
14:30 - Done
14:30 - Finished task "Check high voltages"
14:30 - Starting NMC
14:30 - Clearing PPS error counters
14:31 - Configuring UCTS
14:31 - Configuring TIB...
14:31 - Setting TIB forced mode to False
14:31 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
14:31 - Status: TibState.PpsStopped
14:31 - Alarms: AlarmVector.ReadError
14:31 - Connection status: False
14:31 - Entering set_external_delay
14:31 - Setting ExternalDelayLocal to 0.000 ns
14:31 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
14:31 - Entering set_external_delay
14:31 - Setting ExternalDelayCalibration to 50.000 ns
14:31 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
14:31 - Entering set_external_delay
14:31 - Setting ExternalDelaySphe to 150.000 ns
14:31 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
14:31 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
14:31 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
14:31 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
14:31 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
14:31 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
14:31 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
14:31 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
14:31 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
14:31 - Status: TibState.PpsStopped
14:31 - Alarms: AlarmVector.ReadError
14:31 - Connection status: False
14:31 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
14:31 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
14:31 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:31 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
14:31 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
14:31 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
14:31 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:31 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
14:31 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
14:31 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
14:31 - Connecting TIB to camera server at 10.10.4.12:222
14:31 - Starting TIB...
14:31 - Status: TibState.PpsStopped
14:31 - Alarms: AlarmVector.ReadError
14:31 - Connection status: False
14:31 - Resetting run
14:31 - Wait for UCTS external trigger before enabling trigger...
14:31 - Status: TibState.Standby
14:31 - Alarms: AlarmVector.NoAlarm
14:31 - Connection status: False
14:31 - Status: TibState.Standby
14:31 - Alarms: AlarmVector.NoAlarm
14:31 - Connection status: False
14:31 - Status: TibState.Armed
14:31 - Alarms: AlarmVector.NoAlarm
14:31 - Connection status: True
14:31 - Starting TIB triggers...
14:31 - Enabling trigger
14:31 - Status: TibState.Running
14:31 - Alarms: AlarmVector.NoAlarm
14:31 - Connection status: True
14:31 - Configuring calibration box...
14:31 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=800 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
14:31 - Starting flashes...
14:31 - Checking for high voltage locked pixels...
14:31 - Checking for high voltage locked pixels...
14:32 - Checking for high voltage locked pixels...
14:32 - Stopping TIB...
14:32 - Status: TibState.Running
14:32 - Alarms: AlarmVector.ReadError
14:32 - Connection status: True
14:32 - Disabling trigger
14:32 - Disabling PPS
14:32 - Status: TibState.PpsStopped
14:32 - Alarms: AlarmVector.ReadError
14:32 - Connection status: True
14:32 - Closing TIB connection to camera server
14:32 - Status: TibState.PpsStopped
14:32 - Alarms: AlarmVector.ReadError
14:32 - Connection status: False
14:32 - Run duration: 0:01:36
14:32 - Local camera triggers: 0
14:32 - Slow control triggers: 0
14:32 - Single photo-electron triggers: 0
14:32 - Calibration triggers: 79949
14:32 - Software triggers from UCTS: 0
14:32 - Pedestal triggers: 0
14:32 - Collected input triggers: 79949
14:32 - Busy triggers: 0
14:32 - Camera event triggers sent to clusters: 79949
14:32 - Stopping NMC
14:32 - Found 0 PPS errors.
14:32 - Checking for high voltage locked pixels...
14:32 - Stopped periodic check of locked high voltages
14:32 - Starting task "Switch HVPA voltage state"
14:32 - Setting HVPA current limit to 12489.75 uA