13:34 - ECC is in state EccState.Safe with status EccStatus.NoError
13:34 - Average temperature: 27.8 deg C
13:34 - Air temperature (T1-T6 and T9-T10): 27.7, 27.7, 28.1, 27.8, 28.0, 28.0, 28.6, 28.7 deg C
13:34 - Air differential pressure: 1.6 Pa
13:34 - Water temperature (T11-T12): 29.0, 28.9 deg C
13:34 - Back doors are open.
13:34 - Shutter is in state Open (error 0)
13:34 - Light sensors: [0.01, 0.01, 0.01, 6.82] V
13:34 - Humidity: 42.4 %. Water pressure: [0.1, 0.1] bar.
13:34 - Fan speeds: [0.0, 0.0, 2280.0, 2280.0, 0.0, 0.0] rpm
13:34 - 24 V power supply no. 1 is enabled with a current of 0.840 A.
13:34 - Starting task "Prepare ECC"
13:34 - Preparing ECC...
13:34 - Setting ECC temperature range for Ready state to [16.000000, 35.000000]
13:34 - Setting ECC mode to EccState.Ready
13:34 - Received ECC state change notification: EccState.Safe
13:34 - Received ECC state change notification: EccState.Ready
13:34 - Setting power supply box SPE relay to True
13:34 - Unsubscribing
13:34 - Finished task "Prepare ECC"
13:36 - Status: TibState.Undefined
13:36 - Alarms: AlarmVector.Undefined
13:36 - Connection status: False
13:36 - External delays: Local=3825.000 ns, Calibration=3825.000 ns, Sphe=3825.000 ns
13:36 - Trigger mask: 0x51 = TriggerMask.SlowControl|Software|Mono
13:36 - Input mask: 0x7
13:36 - Disable BUSY: False
13:36 - Extra BUSY Delay: 0.0
13:36 - Temperature: 31.31
13:36 - Status: TibState.RunStopped
13:36 - Alarms: AlarmVector.NoAlarm
13:36 - Connection status: False
13:36 - External delays: Local=3825.000 ns, Calibration=3825.000 ns, Sphe=3825.000 ns
13:36 - Trigger mask: 0x51 = TriggerMask.SlowControl|Software|Mono
13:36 - Input mask: 0x7
13:36 - Disable BUSY: False
13:36 - Extra BUSY Delay: 0.0
13:36 - Temperature: 31.31
13:37 - Starting task "Powering modules..."
13:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
13:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
13:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
13:37 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
13:38 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
13:38 - Finished task "Powering modules..."
13:38 - ECC is in state EccState.Ready with status EccStatus.NoError
13:38 - Average temperature: 27.9 deg C
13:38 - Air temperature (T1-T6 and T9-T10): 27.8, 27.7, 28.1, 27.9, 28.1, 28.4, 28.7, 28.8 deg C
13:38 - Air differential pressure: 1.5 Pa
13:38 - Water temperature (T11-T12): 29.1, 29.0 deg C
13:38 - Back doors are open.
13:38 - Shutter is in state Open (error 0)
13:38 - Light sensors: [0.01, 0.01, 0.01, 6.82] V
13:38 - Humidity: 42.2 %. Water pressure: [0.1, 0.1] bar.
13:38 - Fan speeds: [0.0, 0.0, 2280.0, 2280.0, 0.0, 0.0] rpm
13:38 - 24 V power supply no. 1 is enabled with a current of 58.000 A.
13:38 - Scanning interface p4p1 for non configured modules...
13:38 - Found 27 MAC address(es)
13:38 - Starting task "Configure modules"
13:38 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
13:38 - Switching off high voltages in configuration
13:38 - Successfully configured 61 module(s)
13:38 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
13:38 - Found 0 PPS errors.
13:38 - Finished task "Configure modules"
13:38 - Starting task "Switch HVPA voltage state"
13:38 - Setting HVPA current limit to 12489.75 uA
13:38 - High voltage locked channels will be checked every 30 s
13:39 - Setting HVPA ramp speed to 25 V/s
13:39 - Switching HVPA to state Nominal
13:39 - Setting HVPA current limits...
13:39 - Checking for high voltage locked pixels...
13:39 - Module 66 has 1 pixel(s) locked (HVPA status of 0x7e)!
13:39 - Unlocking 1 channel(s)...
13:39 - Resetting HVPA channel 0 of drawer 66...
13:39 - Finished task "Switch HVPA voltage state"
13:39 - Checking for high voltage locked pixels...
13:39 - Module 111 has 1 pixel(s) locked (HVPA status of 0x7d)!
13:39 - Module 128 has 1 pixel(s) locked (HVPA status of 0x3f)!
13:39 - Unlocking 2 channel(s)...
13:39 - Resetting HVPA channel 1 of drawer 111...
13:39 - Resetting HVPA channel 6 of drawer 128...
13:40 - Stopping flashes...
13:40 - Stopping flashes...
13:40 - Checking for high voltage locked pixels...
13:40 - Stopping flashes...
13:40 - Failed to call Stop: Bad statuses are present
13:40 - Starting task "Check high voltages"
13:40 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
13:40 - Actual voltage is between 945.50 V and 1167.54 V.
13:40 - Low voltages range between 100.00 V and 100.00 V. 
13:40 - Checking for high voltage locked pixels...
13:40 - Reference voltages range between 945.26 V and 1167.15 V. 
13:41 - Maximum difference between expected and actual voltages is 0.99 V
13:41 - Maximum of current limits is 5647.07 uA
13:41 - Checking status of HVPA module in 61 drawer(s)...
13:41 - Checking status of HVPA channels in 61 drawer(s)...
13:41 - Starting NMC
13:41 - Clearing PPS error counters
13:41 - HV is stabilized in all channels.
13:41 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
13:41 - Done
13:41 - Finished task "Check high voltages"
13:41 - Checking for high voltage locked pixels...
13:41 - Configuring UCTS
13:41 - Configuring TIB...
13:41 - Setting TIB forced mode to False
13:41 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
13:41 - Status: TibState.RunStopped
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: False
13:41 - Disabling PPS
13:41 - Status: TibState.PpsStopped
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: False
13:41 - Entering set_external_delay
13:41 - Setting ExternalDelayLocal to 0.000 ns
13:41 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
13:41 - Entering set_external_delay
13:41 - Setting ExternalDelayCalibration to 50.000 ns
13:41 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
13:41 - Entering set_external_delay
13:41 - Setting ExternalDelaySphe to 150.000 ns
13:41 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
13:41 - Setting TIB trigger mode to 0x54 = TriggerMask.SlowControl|Software|Calibration
13:41 - Writing 84 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
13:41 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
13:41 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
13:41 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
13:41 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
13:41 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
13:41 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
13:41 - Status: TibState.PpsStopped
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: False
13:41 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
13:41 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
13:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:41 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
13:41 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
13:41 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
13:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:41 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
13:41 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
13:41 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
13:41 - Connecting TIB to camera server at 10.10.4.12:222
13:41 - Starting TIB...
13:41 - Status: TibState.PpsStopped
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: False
13:41 - Resetting run
13:41 - Wait for UCTS external trigger before enabling trigger...
13:41 - Status: TibState.Standby
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: False
13:41 - Status: TibState.Standby
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: False
13:41 - Status: TibState.Armed
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: True
13:41 - Starting TIB triggers...
13:41 - Enabling trigger
13:41 - Status: TibState.Running
13:41 - Alarms: AlarmVector.NoAlarm
13:41 - Connection status: True
13:41 - Configuring calibration box...
13:41 - Configuring calibration box with leds=0x1fff voltage=16.00 frequency=1000.0/1 central_current=0.0 duration=1000 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
13:41 - Starting flashes...
13:41 - Checking for high voltage locked pixels...
13:42 - Checking for high voltage locked pixels...
13:42 - Checking for high voltage locked pixels...
13:43 - Checking for high voltage locked pixels...
13:43 - Stopping TIB...
13:43 - Status: TibState.Running
13:43 - Alarms: AlarmVector.ReadError
13:43 - Connection status: True
13:43 - Disabling trigger
13:43 - Disabling PPS
13:43 - Status: TibState.PpsStopped
13:43 - Alarms: AlarmVector.ReadError
13:43 - Connection status: True
13:43 - Closing TIB connection to camera server
13:43 - Status: TibState.PpsStopped
13:43 - Alarms: AlarmVector.ReadError
13:43 - Connection status: False
13:43 - Run duration: 0:02:01
13:43 - Local camera triggers: 0
13:43 - Slow control triggers: 0
13:43 - Single photo-electron triggers: 0
13:43 - Calibration triggers: 99932
13:43 - Software triggers from UCTS: 0
13:43 - Pedestal triggers: 0
13:43 - Collected input triggers: 99932
13:43 - Busy triggers: 0
13:43 - Camera event triggers sent to clusters: 99932
13:43 - Checking for high voltage locked pixels...
13:44 - Stopping NMC
13:44 - Found 0 PPS errors.
13:44 - Starting task "Switch HVPA voltage state"
13:44 - Setting HVPA current limit to 12489.75 uA
13:44 - Checking for high voltage locked pixels...
13:44 - Setting HVPA ramp speed to 500 V/s
13:44 - Switching HVPA to state Wait
13:44 - Setting HVPA current limits...
13:44 - Checking for high voltage locked pixels...
13:45 - Stopped periodic check of locked high voltages
13:45 - Finished task "Check high voltages"
13:45 - Starting task "Check high voltages"
13:45 - Found 0 drawer(s) in Nominal state, 0 in Low state and 61 in Wait state
13:45 - Actual voltage is between 234.24 V and 240.95 V.
13:45 - Low voltages range between 100.00 V and 100.00 V. 
13:45 - Reference voltages range between 945.26 V and 1167.15 V. 
13:45 - Maximum difference between expected and actual voltages is 198.25 V
13:45 - Maximum of current limits is 5647.07 uA
13:45 - Checking status of HVPA module in 61 drawer(s)...
13:45 - Checking status of HVPA channels in 61 drawer(s)...
13:46 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 427 channel(s)
13:46 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
13:46 - Done
13:46 - Finished task "Check high voltages"
13:46 - Resetting NMC
13:46 - Starting task "Powering modules..."
13:46 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.57
13:46 - Finished task "Powering modules..."