12:55 - ECC is in state EccState.Ready with status EccStatus.NoError
12:55 - Average temperature: 30.7 deg C
12:55 - Air temperature (T1-T6 and T9-T10): 31.8, 29.7, 30.6, 30.7, 30.9, 31.4, 31.1, 31.2 deg C
12:55 - Air differential pressure: 2.0 Pa
12:55 - Water temperature (T11-T12): 31.4, 31.2 deg C
12:55 - Back doors are open.
12:55 - Shutter is in state Open (error 0)
12:55 - Light sensors: [0.01, 0.01, 0.01, 7.09] V
12:55 - Humidity: 35.6 %. Water pressure: [0.1, 0.1] bar.
12:55 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
12:55 - 24 V power supply no. 1 is enabled with a current of 2.080 A.
12:55 - Starting task "Powering modules..."
12:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 1 --all --power_on' on Digital Trigger Crate at 10.10.4.57
12:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 5 --all --power_on' on Digital Trigger Crate at 10.10.4.57
12:55 - Executing command '/opt/cta/bin/cta_ctrl --slot 9 --all --power_on' on Digital Trigger Crate at 10.10.4.57
12:56 - Executing command '/opt/cta/bin/cta_ctrl --slot 13 --all --power_on' on Digital Trigger Crate at 10.10.4.57
12:56 - Executing command '/opt/cta/bin/cta_ctrl --slot 19 --all --power_on' on Digital Trigger Crate at 10.10.4.57
12:56 - Finished task "Powering modules..."
12:56 - Starting task "Configure modules"
12:56 - Setting L0 thresholds to 3.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
12:56 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190724/config_2019-07-24_12-56-23.NMC.xml
12:56 - Switching off high voltages in configuration
12:56 - Successfully configured 61 module(s)
12:56 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
12:56 - Found 0 PPS errors.
12:56 - Finished task "Configure modules"
12:56 - Starting task "Configure modules"
12:56 - Setting L0 thresholds to 3.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5
12:56 - Configuring modules with configuration /local/home/cta_test_bench/config/2019/20190724/config_2019-07-24_12-56-43.NMC.xml
12:56 - Switching off high voltages in configuration
12:56 - Successfully configured 61 module(s)
12:56 - NMC is in state NmcState.Configured and knows of 61 drawer(s)
12:56 - Found 0 PPS errors.
12:56 - Finished task "Configure modules"
12:56 - Starting task "Switch HVPA voltage state"
12:56 - Setting HVPA current limit to 12489.75 uA
12:57 - High voltage locked channels will be checked every 30 s
12:57 - Setting HVPA ramp speed to 25 V/s
12:57 - Switching HVPA to state Nominal
12:57 - Setting HVPA current limits...
12:57 - Checking for high voltage locked pixels...
12:57 - Finished task "Switch HVPA voltage state"
12:58 - Starting task "Check high voltages"
12:58 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
12:58 - Checking for high voltage locked pixels...
12:58 - Actual voltage is between 945.50 V and 1167.54 V.
12:58 - Low voltages range between 100.00 V and 100.00 V. 
12:58 - Reference voltages range between 945.26 V and 1167.15 V. 
12:58 - Maximum difference between expected and actual voltages is 1.06 V
12:58 - Checking for high voltage locked pixels...
12:58 - Starting NMC
12:58 - Clearing PPS error counters
12:58 - Maximum of current limits is 5647.07 uA
12:58 - Checking status of HVPA module in 61 drawer(s)...
12:58 - Checking status of HVPA channels in 61 drawer(s)...
12:58 - HV is stabilized in all channels.
12:58 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190719/config_61modules_gainswap.NMC.xml
12:59 - Done
12:59 - Finished task "Check high voltages"
12:59 - Configuring UCTS
12:59 - Configuring TIB...
12:59 - Setting TIB forced mode to False
12:59 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
12:59 - Status: TibState.PpsStopped
12:59 - Alarms: AlarmVector.ReadError
12:59 - Connection status: False
12:59 - Entering set_external_delay
12:59 - Setting ExternalDelayLocal to 0.000 ns
12:59 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
12:59 - Entering set_external_delay
12:59 - Setting ExternalDelayCalibration to 50.000 ns
12:59 - Writing 50.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
12:59 - Entering set_external_delay
12:59 - Setting ExternalDelaySphe to 150.000 ns
12:59 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
12:59 - Setting TIB trigger mode to 0x71 = TriggerMask.SlowControl|Pedestal|Software|Mono
12:59 - Writing 113 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
12:59 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
12:59 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
12:59 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
12:59 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
12:59 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
12:59 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
12:59 - Status: TibState.PpsStopped
12:59 - Alarms: AlarmVector.ReadError
12:59 - Connection status: False
12:59 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
12:59 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
12:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:59 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
12:59 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
12:59 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
12:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:59 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
12:59 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
12:59 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
12:59 - Connecting TIB to camera server at 10.10.4.12:222
12:59 - Starting TIB...
12:59 - Status: TibState.PpsStopped
12:59 - Alarms: AlarmVector.ReadError
12:59 - Connection status: False
12:59 - Resetting run
12:59 - Wait for UCTS external trigger before enabling trigger...
12:59 - Status: TibState.Standby
12:59 - Alarms: AlarmVector.NoAlarm
12:59 - Connection status: False
12:59 - Status: TibState.Standby
12:59 - Alarms: AlarmVector.NoAlarm
12:59 - Connection status: False
12:59 - Status: TibState.Armed
12:59 - Alarms: AlarmVector.NoAlarm
12:59 - Connection status: True
12:59 - Checking for high voltage locked pixels...
12:59 - Starting TIB triggers...
12:59 - Enabling trigger
12:59 - Status: TibState.Running
12:59 - Alarms: AlarmVector.NoAlarm
12:59 - Connection status: True
12:59 - Status: TibState.Running ConnectionStatus: True
12:59 - Alarms: AlarmVector.ReadError
12:59 - Temperature: 46.69
12:59 - Local camera rate: 0.0 Hz
12:59 - Stereo trigger rate: 0.0 Hz
12:59 - SPE trigger rate: 0.0 Hz
12:59 - Calibration trigger rate: 0.0 Hz
12:59 - Software trigger rate: 0.0 Hz
12:59 - Pedestal trigger rate: 999.0 Hz
12:59 - Collected trigger rate: 1000.0 Hz
12:59 - Busy rate: 0.0 Hz
12:59 - Camera trigger rate: 1000.0 Hz
12:59 - Status: TibState.Running ConnectionStatus: True
12:59 - Alarms: AlarmVector.ReadError
12:59 - Temperature: 46.69
12:59 - Local camera rate: 0.0 Hz
12:59 - Stereo trigger rate: 0.0 Hz
12:59 - SPE trigger rate: 0.0 Hz
12:59 - Calibration trigger rate: 0.0 Hz
12:59 - Software trigger rate: 0.0 Hz
12:59 - Pedestal trigger rate: 1000.0 Hz
12:59 - Collected trigger rate: 1000.0 Hz
12:59 - Busy rate: 0.0 Hz
12:59 - Camera trigger rate: 1000.0 Hz
12:59 - Checking for high voltage locked pixels...
12:59 - Stopping TIB...
12:59 - Status: TibState.Running
12:59 - Alarms: AlarmVector.ReadError
12:59 - Connection status: True
12:59 - Disabling trigger
12:59 - Disabling PPS
12:59 - Status: TibState.PpsStopped
12:59 - Alarms: AlarmVector.ReadError
12:59 - Connection status: True
12:59 - Closing TIB connection to camera server
13:00 - Status: TibState.PpsStopped
13:00 - Alarms: AlarmVector.ReadError
13:00 - Connection status: False
13:00 - Run duration: 0:00:37
13:00 - Local camera triggers: 0
13:00 - Slow control triggers: 0
13:00 - Single photo-electron triggers: 0
13:00 - Calibration triggers: 0
13:00 - Software triggers from UCTS: 0
13:00 - Pedestal triggers: 36151
13:00 - Collected input triggers: 34180
13:00 - Busy triggers: 1
13:00 - Camera event triggers sent to clusters: 34179
13:00 - Checking for high voltage locked pixels...
13:00 - Stopping NMC
13:00 - Found 0 PPS errors.
13:00 - Starting task "Switch HVPA voltage state"
13:00 - Setting HVPA current limit to 12489.75 uA
13:00 - Checking for high voltage locked pixels...
13:01 - Stopped periodic check of locked high voltages
13:01 - Setting HVPA ramp speed to 500 V/s
13:01 - Switching HVPA to state Wait
13:01 - Setting HVPA current limits...
13:01 - Finished task "Check high voltages"
13:01 - Starting task "Check high voltages"
13:01 - Found 0 drawer(s) in Nominal state, 0 in Low state and 61 in Wait state
13:02 - Actual voltage is between 253.15 V and 258.03 V.
13:02 - Low voltages range between 100.00 V and 100.00 V. 
13:02 - Resetting NMC
13:02 - Failed to read ' - type : ExpandedNodeId - expandedNodeId : Svr='urn:UnifiedAutomation:UaServerCpp'|Ns='urn:Lpnhe:NectarCam:NMC'|String|NectarFrontEnd_133.Hvpa.Hvpa1.Voltage': Bad statuses are present (code OpcUa_BadNodeIdUnknown)
13:02 - Finished task "Check high voltages"
13:02 - Starting task "Powering modules..."
13:02 - Executing command '/opt/cta/bin/cta_ctrl --all --power_off' on Digital Trigger Crate at 10.10.4.57
13:02 - Finished task "Powering modules..."
13:02 - ECC is in state EccState.Ready with status EccStatus.NoError
13:02 - Average temperature: 30.9 deg C
13:02 - Air temperature (T1-T6 and T9-T10): 32.0, 29.9, 30.9, 30.9, 31.3, 31.7, 31.3, 31.5 deg C
13:02 - Air differential pressure: 2.2 Pa
13:02 - Water temperature (T11-T12): 31.7, 31.5 deg C
13:02 - Back doors are open.
13:02 - Shutter is in state Open (error 0)
13:02 - Light sensors: [0.01, 0.01, 0.01, 7.11] V
13:02 - Humidity: 35.3 %. Water pressure: [0.1, 0.1] bar.
13:02 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
13:02 - 24 V power supply no. 1 is enabled with a current of 2.090 A.