23:45 - ECC is in state EccState.Ready with status EccStatus.NoError
23:45 - Average temperature: 20.4 deg C
23:45 - Air temperature (T1-T6 and T9-T10): 21.9, 18.9, 20.5, 20.3, 21.8, 22.9, 21.1, 21.1 deg C
23:45 - Air differential pressure: 1.4 Pa
23:45 - Water temperature (T11-T12): 21.3, 21.2 deg C
23:45 - Back doors are closed.
23:45 - Shutter is in state Open (error 0)
23:45 - Light sensors: [0.01, 0.01, 0.01, 6.05] V
23:45 - Humidity: 60.5 %. Water pressure: [2.9, 4.5] bar.
23:45 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
23:45 - 24 V power supply no. 1 is enabled with a current of 59.000 A.
23:45 - Stopping NMC
23:45 - Found 0 PPS errors.
23:45 - Starting task "Check high voltages"
23:45 - Checking for high voltage locked pixels...
23:45 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
23:45 - Actual voltage is between 945.50 V and 1167.54 V.
23:45 - Low voltages range between 100.00 V and 100.00 V. 
23:45 - Reference voltages range between 945.26 V and 1167.15 V. 
23:46 - Checking for high voltage locked pixels...
23:46 - Maximum difference between expected and actual voltages is 7.95 V
23:46 - Maximum of current limits is 5647.07 uA
23:46 - Checking status of HVPA module in 61 drawer(s)...
23:46 - Checking status of HVPA channels in 61 drawer(s)...
23:46 - HV is stabilized in all channels.
23:46 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190519/config_61modules_cameraqm_moduleSwap3.NMC.xml
23:46 - Done
23:46 - Finished task "Check high voltages"
23:46 - Checking for high voltage locked pixels...
23:46 - Starting task "Check high voltages"
23:46 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
23:46 - Actual voltage is between 945.50 V and 1167.54 V.
23:46 - Low voltages range between 100.00 V and 100.00 V. 
23:46 - Reference voltages range between 945.26 V and 1167.15 V. 
23:47 - Checking for high voltage locked pixels...
23:47 - Maximum difference between expected and actual voltages is 0.71 V
23:47 - Maximum of current limits is 5647.07 uA
23:47 - Checking status of HVPA module in 61 drawer(s)...
23:47 - Checking status of HVPA channels in 61 drawer(s)...
23:47 - HV is stabilized in all channels.
23:47 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190519/config_61modules_cameraqm_moduleSwap3.NMC.xml
23:47 - Done
23:47 - Finished task "Check high voltages"
23:47 - Starting NMC
23:47 - Clearing PPS error counters
23:47 - Checking for high voltage locked pixels...
23:48 - Checking for high voltage locked pixels...
23:48 - Checking for high voltage locked pixels...
23:49 - Checking for high voltage locked pixels...
23:49 - Checking for high voltage locked pixels...
23:50 - Checking for high voltage locked pixels...
23:50 - Configuring UCTS
23:50 - Configuring TIB...
23:50 - Setting TIB forced mode to False
23:50 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
23:50 - Status: TibState.PpsStopped
23:50 - Alarms: AlarmVector.ReadError
23:50 - Connection status: False
23:50 - Entering set_external_delay
23:50 - Setting ExternalDelayLocal to 0.000 ns
23:50 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
23:50 - Entering set_external_delay
23:50 - Setting ExternalDelayCalibration to 78.000 ns
23:50 - Writing 78.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
23:50 - Entering set_external_delay
23:50 - Setting ExternalDelaySphe to 150.000 ns
23:50 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
23:50 - Setting TIB trigger mode to 0x74 = TriggerMask.SlowControl|Pedestal|Software|Calibration
23:50 - Writing 116 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
23:50 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
23:50 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
23:50 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
23:50 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
23:50 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
23:50 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
23:50 - Status: TibState.PpsStopped
23:50 - Alarms: AlarmVector.ReadError
23:50 - Connection status: False
23:50 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
23:50 - Writing 100 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
23:50 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
23:50 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
23:50 - Writing 100 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
23:50 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
23:50 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
23:50 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
23:50 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
23:50 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
23:50 - Connecting TIB to camera server at 10.10.4.12:222
23:50 - Starting TIB...
23:50 - Status: TibState.PpsStopped
23:50 - Alarms: AlarmVector.ReadError
23:50 - Connection status: False
23:50 - Resetting run
23:50 - Wait for UCTS external trigger before enabling trigger...
23:50 - Status: TibState.Standby
23:50 - Alarms: AlarmVector.NoAlarm
23:50 - Connection status: False
23:50 - Status: TibState.Standby
23:50 - Alarms: AlarmVector.NoAlarm
23:50 - Connection status: False
23:50 - Status: TibState.Armed
23:50 - Alarms: AlarmVector.NoAlarm
23:50 - Connection status: True
23:50 - Checking for high voltage locked pixels...
23:50 - Configuring calibration box...
23:50 - Configuring calibration box with leds=0x35a voltage=8.00 frequency=300.0/3 central_current=0.0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
23:50 - Starting flashes...
23:51 - Starting TIB triggers...
23:51 - Enabling trigger
23:51 - Status: TibState.Running
23:51 - Alarms: AlarmVector.NoAlarm
23:51 - Connection status: True
23:51 - Checking for high voltage locked pixels...
23:51 - Checking for high voltage locked pixels...
23:51 - Status: TibState.Running ConnectionStatus: True
23:51 - Alarms: AlarmVector.ReadError
23:51 - Temperature: 38.50
23:51 - Local camera rate: 0.0 Hz
23:51 - Stereo trigger rate: 0.0 Hz
23:51 - SPE trigger rate: 0.0 Hz
23:51 - Calibration trigger rate: 100.0 Hz
23:51 - Software trigger rate: 0.0 Hz
23:51 - Pedestal trigger rate: 100.0 Hz
23:51 - Collected trigger rate: 200.0 Hz
23:51 - Busy rate: 0.0 Hz
23:51 - Camera trigger rate: 200.0 Hz
23:51 - Stopping TIB...
23:51 - Status: TibState.Running
23:51 - Alarms: AlarmVector.ReadError
23:51 - Connection status: True
23:51 - Disabling trigger
23:51 - Disabling PPS
23:51 - Status: TibState.PpsStopped
23:51 - Alarms: AlarmVector.ReadError
23:51 - Connection status: True
23:51 - Closing TIB connection to camera server
23:52 - Checking for high voltage locked pixels...
23:52 - Status: TibState.PpsStopped
23:52 - Alarms: AlarmVector.ReadError
23:52 - Connection status: False
23:52 - Run duration: 0:01:26
23:52 - Local camera triggers: 0
23:52 - Slow control triggers: 0
23:52 - Single photo-electron triggers: 0
23:52 - Calibration triggers: 5768
23:52 - Software triggers from UCTS: 0
23:52 - Pedestal triggers: 8595
23:52 - Collected input triggers: 10535
23:52 - Busy triggers: 0
23:52 - Camera event triggers sent to clusters: 10535