23:04 - ECC is in state EccState.Ready with status EccStatus.NoError
23:04 - Average temperature: 19.3 deg C
23:04 - Air temperature (T1-T6 and T9-T10): 20.7, 17.9, 19.3, 19.2, 20.1, 21.4, 20.2, 20.1 deg C
23:04 - Air differential pressure: 0.9 Pa
23:04 - Water temperature (T11-T12): 20.3, 20.3 deg C
23:04 - Back doors are closed.
23:04 - Shutter is in state PartiallyOpen (error 0)
23:04 - Light sensors: [0.01, 0.01, 0.0, 5.9] V
23:04 - Humidity: 64.0 %. Water pressure: [2.92, 4.52] bar.
23:04 - Fan speeds: [0.0, 0.0, 2400.0, 2400.0, 0.0, 0.0] rpm
23:04 - 24 V power supply no. 1 is enabled with a current of 58.800 A.
23:04 - Checking for high voltage locked pixels...
23:04 - Stopping NMC
23:04 - Found 0 PPS errors.
23:04 - Starting task "Check high voltages"
23:04 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
23:04 - Starting NMC
23:04 - Clearing PPS error counters
23:04 - Actual voltage is between 945.50 V and 1167.54 V.
23:04 - Low voltages range between 100.00 V and 100.00 V. 
23:05 - Reference voltages range between 945.26 V and 1167.15 V. 
23:05 - Checking for high voltage locked pixels...
23:05 - Maximum difference between expected and actual voltages is 0.81 V
23:05 - Maximum of current limits is 5647.07 uA
23:05 - Checking status of HVPA module in 61 drawer(s)...
23:05 - Checking status of HVPA channels in 61 drawer(s)...
23:05 - HV is stabilized in all channels.
23:05 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190519/config_61modules_cameraqm_moduleSwap3.NMC.xml
23:05 - Done
23:05 - Finished task "Check high voltages"
23:05 - Checking for high voltage locked pixels...
23:05 - Configuring UCTS
23:05 - Configuring TIB...
23:05 - Setting TIB forced mode to False
23:05 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
23:05 - Status: TibState.PpsStopped
23:05 - Alarms: AlarmVector.ReadError
23:05 - Connection status: False
23:05 - Entering set_external_delay
23:05 - Setting ExternalDelayLocal to 0.000 ns
23:05 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
23:05 - Entering set_external_delay
23:05 - Setting ExternalDelayCalibration to 78.000 ns
23:05 - Writing 78.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
23:05 - Entering set_external_delay
23:05 - Setting ExternalDelaySphe to 150.000 ns
23:05 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
23:05 - Setting TIB trigger mode to 0x70 = TriggerMask.SlowControl|Pedestal|Software
23:05 - Writing 112 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
23:05 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
23:05 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
23:05 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
23:05 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
23:05 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
23:05 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
23:05 - Status: TibState.PpsStopped
23:05 - Alarms: AlarmVector.ReadError
23:05 - Connection status: False
23:05 - Writing True to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
23:05 - Writing 2000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
23:05 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
23:05 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
23:05 - Writing 2000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
23:05 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
23:05 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
23:05 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
23:05 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
23:05 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
23:05 - Connecting TIB to camera server at 10.10.4.12:222
23:05 - Starting TIB...
23:05 - Status: TibState.PpsStopped
23:05 - Alarms: AlarmVector.ReadError
23:05 - Connection status: False
23:05 - Resetting run
23:05 - Wait for UCTS external trigger before enabling trigger...
23:05 - Status: TibState.Standby
23:05 - Alarms: AlarmVector.NoAlarm
23:05 - Connection status: False
23:05 - Status: TibState.Standby
23:05 - Alarms: AlarmVector.NoAlarm
23:05 - Connection status: False
23:05 - Status: TibState.Armed
23:05 - Alarms: AlarmVector.NoAlarm
23:05 - Connection status: True
23:06 - Starting TIB triggers...
23:06 - Enabling trigger
23:06 - Status: TibState.Running
23:06 - Alarms: AlarmVector.NoAlarm
23:06 - Connection status: True
23:06 - Checking for high voltage locked pixels...
23:06 - Stopping TIB...
23:06 - Status: TibState.Running
23:06 - Alarms: AlarmVector.ReadError
23:06 - Connection status: True
23:06 - Disabling trigger
23:06 - Disabling PPS
23:06 - Status: TibState.PpsStopped
23:06 - Alarms: AlarmVector.ReadError
23:06 - Connection status: True
23:06 - Closing TIB connection to camera server
23:06 - Status: TibState.PpsStopped
23:06 - Alarms: AlarmVector.ReadError
23:06 - Connection status: False
23:06 - Run duration: 0:00:30
23:06 - Local camera triggers: 0
23:06 - Slow control triggers: 0
23:06 - Single photo-electron triggers: 0
23:06 - Calibration triggers: 0
23:06 - Software triggers from UCTS: 0
23:06 - Pedestal triggers: 59691
23:06 - Collected input triggers: 52293
23:06 - Busy triggers: 0
23:06 - Camera event triggers sent to clusters: 52293
23:06 - Checking for high voltage locked pixels...