00:28 - ECC is in state EccState.Ready with status EccStatus.NoError 00:28 - Average temperature: 23.2 deg C 00:28 - Air temperature (T1-T6 and T9-T10): 23.2, 19.9, 21.0, 21.8, 21.9, 22.6, 19.3, 19.6 deg C 00:28 - Air differential pressure: 1.1 Pa 00:28 - Water temperature (T11-T12): 19.6, 19.4 deg C 00:28 - Back doors are closed. 00:28 - Shutter is in status ShutterStatus.PartiallyOpen (error 0) 00:28 - Light sensors: [0.01, 0.01, 0.01, 6.16] V 00:28 - Humidity: 43.3 %. Water pressure: [4.02, 5.52] bar. 00:28 - Fan speeds: [0.0, 0.0, 2160.0, 2160.0, 0.0, 0.0] rpm 00:28 - 24 V power supply no. 1 is enabled with a current of 57.800 A. 00:28 - Starting NMC 00:28 - Clearing PPS error counters 00:28 - Checking for high voltage locked pixels... 00:28 - Starting task "Switch HVPA voltage state" 00:28 - Setting HVPA current limit to 12489.75 uA 00:28 - Setting HVPA ramp speed to 35 V/s 00:28 - Checking for high voltage locked pixels... 00:28 - Switching HVPA to state Nominal 00:29 - Setting HVPA current limits... 00:29 - Checking for high voltage locked pixels... 00:29 - Finished task "Switch HVPA voltage state" 00:29 - Checking for high voltage locked pixels... 00:30 - Checking for high voltage locked pixels... 00:30 - Starting task "Check high voltages" 00:30 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state 00:30 - Actual voltage is between 945.50 V and 1167.54 V. 00:30 - Low voltages range between 100.00 V and 100.00 V. 00:30 - Reference voltages range between 945.26 V and 1167.15 V. 00:30 - Checking for high voltage locked pixels... 00:31 - Maximum difference between expected and actual voltages is 0.71 V 00:31 - Maximum of current limits is 5647.07 uA 00:31 - Checking status of HVPA module in 61 drawer(s)... 00:31 - Checking status of HVPA channels in 61 drawer(s)... 00:31 - HV is stabilized in all channels. 00:31 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190518/config_61modules_cameraqm_moduleSwap2.NMC.xml 00:31 - Done 00:31 - Finished task "Check high voltages" 00:31 - NMC is in state NmcState.Running and knows of 61 drawer(s) 00:31 - Found 0 PPS errors. 00:31 - Checking for high voltage locked pixels... 00:31 - Starting task "Set L0 trigger thresholds" 00:31 - Setting L0 thresholds to 30.0 p.e. 00:31 - Checking for high voltage locked pixels... 00:32 - Setting L0 thresholds to 30.0 p.e. per pixel using L0 slopes and offsets in /local/home/cta_test_bench/data/2019/20190328/l0_threshold_slope_and_offset.h5 00:32 - Thresholds saved in configuration file /local/home/cta_test_bench/config/2019/20190519/config_2019-05-19_00-32-01.NMC.xml 00:32 - Finished task "Set L0 trigger thresholds" 00:32 - Configuring UCTS 00:32 - Configuring TIB... 00:32 - Setting TIB forced mode to False 00:32 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v 00:32 - Status: TibState.PpsStopped 00:32 - Alarms: AlarmVector.BufferFull|AlmostFull 00:32 - Connection status: False 00:32 - Entering set_external_delay 00:32 - Setting ExternalDelayLocal to 0.000 ns 00:32 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v 00:32 - Entering set_external_delay 00:32 - Setting ExternalDelayCalibration to 55.000 ns 00:32 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v 00:32 - Entering set_external_delay 00:32 - Setting ExternalDelaySphe to 150.000 ns 00:32 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v 00:32 - Setting TIB trigger mode to 0x51 = TriggerMask.SlowControl|Software|Mono 00:32 - Writing 81 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v 00:32 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v 00:32 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v 00:32 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v 00:32 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v 00:32 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v 00:32 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v 00:32 - Status: TibState.PpsStopped 00:32 - Alarms: AlarmVector.BufferFull|AlmostFull 00:32 - Connection status: False 00:32 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v 00:32 - Writing 1000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v 00:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v 00:32 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v 00:32 - Writing 1000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v 00:32 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v 00:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v 00:32 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v 00:32 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v 00:32 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v 00:32 - Checking for high voltage locked pixels... 00:32 - Stopping flashes... 00:32 - Stopping flashes... 00:32 - Connecting TIB to camera server at 10.10.4.12:222 00:32 - Starting TIB... 00:32 - Status: TibState.PpsStopped 00:32 - Alarms: AlarmVector.BufferFull|AlmostFull 00:32 - Connection status: False 00:32 - Resetting run 00:32 - Wait for UCTS external trigger before enabling trigger... 00:32 - Status: TibState.Standby 00:32 - Alarms: AlarmVector.NoAlarm 00:32 - Connection status: False 00:32 - Status: TibState.Standby 00:32 - Alarms: AlarmVector.NoAlarm 00:32 - Connection status: False 00:32 - Status: TibState.Armed 00:32 - Alarms: AlarmVector.NoAlarm 00:32 - Connection status: True 00:32 - Starting TIB triggers... 00:32 - Enabling trigger 00:32 - Status: TibState.Running 00:32 - Alarms: AlarmVector.NoAlarm 00:32 - Connection status: True 00:32 - Checking for high voltage locked pixels... 00:33 - Checking for high voltage locked pixels... 00:33 - Checking for high voltage locked pixels... 00:34 - Checking for high voltage locked pixels... 00:34 - Stopping TIB... 00:34 - Status: TibState.Running 00:34 - Alarms: AlarmVector.NoAlarm 00:34 - Connection status: True 00:34 - Disabling trigger 00:34 - Disabling PPS 00:34 - Status: TibState.PpsStopped 00:34 - Alarms: AlarmVector.NoAlarm 00:34 - Connection status: True 00:34 - Closing TIB connection to camera server 00:34 - Status: TibState.PpsStopped 00:34 - Alarms: AlarmVector.NoAlarm 00:34 - Connection status: False 00:34 - Run duration: 0:02:01 00:34 - Local camera triggers: 0 00:34 - Slow control triggers: 0 00:34 - Single photo-electron triggers: 0 00:34 - Calibration triggers: 0 00:34 - Software triggers from UCTS: 0 00:34 - Pedestal triggers: 0 00:34 - Collected input triggers: 29 00:34 - Busy triggers: 0 00:34 - Camera event triggers sent to clusters: 29 00:34 - Checking for high voltage locked pixels...