16:06 - High voltage locked channels will be checked every 30 s
16:06 - Finished task "Switch HVPA voltage state"
16:06 - Starting task "Check high voltages"
16:06 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:06 - Actual voltage is between 23.79 V and 1167.54 V.
16:06 - Low voltages range between 100.00 V and 100.00 V. 
16:06 - Reference voltages range between 0.00 V and 1167.15 V. 
16:06 - Checking for high voltage locked pixels...
16:06 - Module 83 has 1 pixel(s) locked (HVPA status of 0x77)!
16:06 - Module 111 has 1 pixel(s) locked (HVPA status of 0x7d)!
16:06 - Unlocking 2 channel(s)...
16:06 - Resetting HVPA channel 3 of drawer 83...
16:06 - Resetting HVPA channel 1 of drawer 111...
16:06 - Maximum difference between expected and actual voltages is 14.03 V
16:06 - Maximum of current limits is 5647.07 uA
16:06 - Checking status of HVPA module in 61 drawer(s)...
16:06 - Checking status of HVPA channels in 61 drawer(s)...
16:07 - HV is locked in 0 channel(s), was in rise default in 0 channel(s) and was still in progress in 2 channel(s)
16:07 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:07 - Done
16:07 - Finished task "Check high voltages"
16:07 - Checking for high voltage locked pixels...
16:07 - Checking for high voltage locked pixels...
16:08 - Checking for high voltage locked pixels...
16:08 - Checking status of calibration box...
16:08 - Calibration box is configured with 1 leds at a frequency of 2000.0 Hz and a voltage of 15.00 V
16:08 - Checking for high voltage locked pixels...
16:08 - Configuring calibration box...
16:08 - Configuring calibration box with leds=0x1fbf voltage=15.00 frequency=2000.0/1 central_current=0.0 duration=200 width=1 lemo_out=True fiber1_out=False fiber2_out=False lemo_in=False enabled=False
16:09 - Checking for high voltage locked pixels...
16:09 - Checking for high voltage locked pixels...
16:09 - Stopping flashes...
16:10 - Starting task "Check high voltages"
16:10 - Found 61 drawer(s) in Nominal state, 0 in Low state and 0 in Wait state
16:10 - Actual voltage is between 944.89 V and 1166.93 V.
16:10 - Low voltages range between 100.00 V and 100.00 V. 
16:10 - Checking for high voltage locked pixels...
16:10 - Reference voltages range between 945.26 V and 1167.15 V. 
16:10 - Maximum difference between expected and actual voltages is 0.72 V
16:10 - Maximum of current limits is 5647.07 uA
16:10 - Checking status of HVPA module in 61 drawer(s)...
16:10 - Checking status of HVPA channels in 61 drawer(s)...
16:10 - HV is stabilized in all channels.
16:10 - Checking reference and low voltages against /local/home/cta_test_bench/config/2019/20190401/config_61modules_cameraqm_l1a+l0delays_nd.NMC.xml
16:10 - Checking for high voltage locked pixels...
16:10 - Done
16:10 - Finished task "Check high voltages"
16:11 - Checking for high voltage locked pixels...
16:11 - Stopping NMC
16:11 - Found 0 PPS errors.
16:11 - Starting NMC
16:11 - Clearing PPS error counters
16:11 - Checking for high voltage locked pixels...
16:11 - Configuring UCTS
16:11 - Configuring TIB...
16:11 - Setting TIB forced mode to False
16:11 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:11 - Status: TibState.Running
16:11 - Alarms: AlarmVector.BufferFull|AlmostFull
16:11 - Connection status: True
16:11 - Disabling PPS
16:11 - Error configuring TIB: Failed to call DisablePPS: Bad statuses are present
16:11 - Stopping TIB...
16:11 - Status: TibState.Running
16:11 - Alarms: AlarmVector.BufferFull|AlmostFull
16:11 - Connection status: True
16:11 - Disabling trigger
16:11 - Disabling PPS
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.BufferFull|AlmostFull
16:12 - Connection status: True
16:12 - Closing TIB connection to camera server
16:12 - Resetting TIB...
16:12 - Failed to call Reset: Bad statuses are present
16:12 - Configuring UCTS
16:12 - Configuring TIB...
16:12 - Setting TIB forced mode to False
16:12 - Writing False to Camera.TIB.Forced.ForcedMode.ForcedMode_v
16:12 - Status: TibState.RunStopped
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Disabling PPS
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Entering set_external_delay
16:12 - Setting ExternalDelayLocal to 0.000 ns
16:12 - Writing 0.0 to Camera.TIB.ExternalDelay.ExternalDelayLocal.ExternalDelayLocal_v
16:12 - Entering set_external_delay
16:12 - Setting ExternalDelayCalibration to 55.000 ns
16:12 - Writing 55.0 to Camera.TIB.ExternalDelay.ExternalDelayCalibration.ExternalDelayCalibration_v
16:12 - Entering set_external_delay
16:12 - Setting ExternalDelaySphe to 150.000 ns
16:12 - Writing 150.0 to Camera.TIB.ExternalDelay.ExternalDelaySphe.ExternalDelaySphe_v
16:12 - Setting TIB trigger mode to 0x48 = TriggerMask.SlowControl|SPhE
16:12 - Writing 72 to Camera.TIB.TriggerMode.ModeMask.ModeMask_v
16:12 - Writing 0 to Camera.TIB.InputsEnable.InputMask.InputMask_v
16:12 - Writing False to Camera.TIB.BUSY.DisableBusy.DisableBusy_v
16:12 - Writing 0.0 to Camera.TIB.BUSY.ExtraDelayBusy.ExtraDelayBusy_v
16:12 - Writing False to Camera.TIB.Throttler.DisableThrottler.DisableThrottler_v
16:12 - Writing 255 to Camera.TIB.Throttler.MaxTriggers50us.MaxTriggers50us_v
16:12 - Writing 255 to Camera.TIB.Throttler.MaxTriggers1ms.MaxTriggers1ms_v
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Writing False to Camera.TIB.Pedestal.PeriodicPedestalEnable.PeriodicPedestalEnable_v
16:12 - Writing 6000 to Camera.TIB.Pedestal.PeriodicPedestalFrequency.PeriodicPedestalFrequency_v
16:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:12 - Writing False to Camera.TIB.Pedestal.DigitalPedestalEnable.DigitalPedestalEnable_v
16:12 - Writing 6000 to Camera.TIB.Pedestal.DigitalPedestal_config_Rate.DigitalPedestal_config_Rate_v
16:12 - Writing 375764 to Camera.TIB.Pedestal.DigitalPedestalSeed.DigitalPedestalSeed_v
16:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:12 - Writing False to Camera.TIB.Pedestal.AnalogPedestalEnable.AnalogPedestalEnable_v
16:12 - Writing 3000.0 to Camera.TIB.Pedestal.AnalogPedestalThreshold.AnalogPedestalThreshold_v
16:12 - Writing False to Camera.TIB.Pedestal.Fake_trig_enable.Fake_trig_enable_v
16:12 - Checking for high voltage locked pixels...
16:12 - Checking for high voltage locked pixels...
16:12 - Connecting TIB to camera server at 10.10.4.12:222
16:12 - Starting TIB...
16:12 - Status: TibState.PpsStopped
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Resetting run
16:12 - Wait for UCTS external trigger before enabling trigger...
16:12 - Status: TibState.Standby
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Status: TibState.Standby
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: False
16:12 - Status: TibState.Armed
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: True
16:12 - Starting TIB triggers...
16:12 - Enabling trigger
16:12 - Status: TibState.Running
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Connection status: True
16:12 - Status: TibState.Running ConnectionStatus: True
16:12 - Alarms: AlarmVector.NoAlarm
16:12 - Temperature: 40.81
16:12 - Local camera rate: 0.0 Hz
16:12 - Stereo trigger rate: 0.0 Hz
16:12 - SPE trigger rate: 0.0 Hz
16:12 - Calibration trigger rate: 0.0 Hz
16:12 - Software trigger rate: 0.0 Hz
16:12 - Pedestal trigger rate: 0.0 Hz
16:12 - Collected trigger rate: 0.0 Hz
16:12 - Busy rate: 0.0 Hz
16:12 - Camera trigger rate: 0.0 Hz
2019-04-26 16:13:23,267 Configuring calibration box with leds=0x1bf voltage=15.00 frequency=300/3 central_current=0 duration=0 width=1 lemo_out=True fiber1_out=True fiber2_out=True lemo_in=False enabled=False
2019-04-26 16:13:23,267 Calling method NectarCAM.CalibrationBox.Configure in object NectarCAM.CalibrationBox
2019-04-26 16:13:23,347 Moving XY table to position 0: module 79
2019-04-26 16:13:23,405 Module 79 is located at (X=-34.4 cm, Y=19.8 cm) in camera coordinates
2019-04-26 16:13:23,406 Module 79 is located at (X=118.4 cm, Y=113.8 cm) in XY table coordinates
2019-04-26 16:13:23,406 Moving XY table to position (Xtable=118.4 cm, Ytable=113.8 cm)
2019-04-26 16:13:23,406 Selecting XY table position: 118.4, 113.8
2019-04-26 16:13:23,410 Moving to next XY table position
2019-04-26 16:13:23,412 Waiting for XY table to be busy...
2019-04-26 16:13:24,244 XY table busy state changed to: True
2019-04-26 16:13:24,245 XY table parking state changed to: True
2019-04-26 16:13:24,247 XY table IS busy
2019-04-26 16:13:24,247 Waiting for XY table to be idle...
2019-04-26 16:14:54,208 XY table busy state changed to: False
2019-04-26 16:14:54,208 XY table parking state changed to: False
2019-04-26 16:14:54,210 XY table is NOT busy
2019-04-26 16:14:54,214 Current position: (X=118.37 cm, Y=113.83 cm) in XY table coordinates
2019-04-26 16:14:54,218 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:14:57,220 Starting SPE flasher
2019-04-26 16:14:57,220 Starting flashes...
2019-04-26 16:14:57,221 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:15:18,291 Stopping SPE flasher
2019-04-26 16:15:18,291 Stopping flashes...
2019-04-26 16:15:18,291 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:15:19,341 Triggering TIB by slow control
2019-04-26 16:15:19,341 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:15:19,344 Moving XY table to position 1: module 81
2019-04-26 16:15:19,355 Module 81 is located at (X=-34.4 cm, Y=-6.6 cm) in camera coordinates
2019-04-26 16:15:19,356 Module 81 is located at (X=118.4 cm, Y=87.4 cm) in XY table coordinates
2019-04-26 16:15:19,356 Moving XY table to position (Xtable=118.4 cm, Ytable=87.4 cm)
2019-04-26 16:15:19,356 Selecting XY table position: 118.4, 87.4
2019-04-26 16:15:19,359 Moving to next XY table position
2019-04-26 16:15:19,361 Waiting for XY table to be busy...
2019-04-26 16:15:20,207 XY table busy state changed to: True
2019-04-26 16:15:20,209 XY table IS busy
2019-04-26 16:15:20,209 Waiting for XY table to be idle...
2019-04-26 16:15:37,208 XY table busy state changed to: False
2019-04-26 16:15:37,211 XY table is NOT busy
2019-04-26 16:15:37,215 Current position: (X=118.37 cm, Y=87.39 cm) in XY table coordinates
2019-04-26 16:15:37,219 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:15:40,220 Starting SPE flasher
2019-04-26 16:15:40,220 Starting flashes...
2019-04-26 16:15:40,220 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:16:01,291 Stopping SPE flasher
2019-04-26 16:16:01,291 Stopping flashes...
2019-04-26 16:16:01,291 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:16:02,342 Triggering TIB by slow control
2019-04-26 16:16:02,342 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:16:02,345 Moving XY table to position 2: module 83
2019-04-26 16:16:02,356 Module 83 is located at (X=-34.4 cm, Y=-33.1 cm) in camera coordinates
2019-04-26 16:16:02,357 Module 83 is located at (X=118.4 cm, Y=60.9 cm) in XY table coordinates
2019-04-26 16:16:02,357 Moving XY table to position (Xtable=118.4 cm, Ytable=60.9 cm)
2019-04-26 16:16:02,357 Selecting XY table position: 118.4, 60.9
2019-04-26 16:16:02,361 Moving to next XY table position
2019-04-26 16:16:02,363 Waiting for XY table to be busy...
2019-04-26 16:16:03,211 XY table busy state changed to: True
2019-04-26 16:16:03,213 XY table IS busy
2019-04-26 16:16:03,213 Waiting for XY table to be idle...
2019-04-26 16:16:20,214 XY table busy state changed to: False
2019-04-26 16:16:20,216 XY table is NOT busy
2019-04-26 16:16:20,220 Current position: (X=118.37 cm, Y=60.93 cm) in XY table coordinates
2019-04-26 16:16:20,224 Distance between expected and actual positions: 0.00 cm
2019-04-26 16:16:23,227 Starting SPE flasher
2019-04-26 16:16:23,227 Starting flashes...
2019-04-26 16:16:23,227 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:16:44,298 Stopping SPE flasher
2019-04-26 16:16:44,298 Stopping flashes...
2019-04-26 16:16:44,298 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:16:45,349 Triggering TIB by slow control
2019-04-26 16:16:45,350 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:16:45,353 Moving XY table to position 3: module 118
2019-04-26 16:16:45,364 Module 118 is located at (X=-11.5 cm, Y=-46.3 cm) in camera coordinates
2019-04-26 16:16:45,365 Module 118 is located at (X=95.5 cm, Y=47.7 cm) in XY table coordinates
2019-04-26 16:16:45,365 Moving XY table to position (Xtable=95.5 cm, Ytable=47.7 cm)
2019-04-26 16:16:45,365 Selecting XY table position: 95.5, 47.7
2019-04-26 16:16:45,369 Moving to next XY table position
2019-04-26 16:16:45,371 Waiting for XY table to be busy...
2019-04-26 16:16:46,214 XY table busy state changed to: True
2019-04-26 16:16:46,217 XY table IS busy
2019-04-26 16:16:46,217 Waiting for XY table to be idle...
2019-04-26 16:17:06,214 XY table busy state changed to: False
2019-04-26 16:17:06,217 XY table is NOT busy
2019-04-26 16:17:06,221 Current position: (X=95.45 cm, Y=47.70 cm) in XY table coordinates
2019-04-26 16:17:06,225 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:17:09,226 Starting SPE flasher
2019-04-26 16:17:09,226 Starting flashes...
2019-04-26 16:17:09,227 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:17:30,287 Stopping SPE flasher
2019-04-26 16:17:30,288 Stopping flashes...
2019-04-26 16:17:30,288 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:17:31,338 Triggering TIB by slow control
2019-04-26 16:17:31,339 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:17:31,342 Moving XY table to position 4: module 116
2019-04-26 16:17:31,352 Module 116 is located at (X=-11.5 cm, Y=-19.8 cm) in camera coordinates
2019-04-26 16:17:31,352 Module 116 is located at (X=95.5 cm, Y=74.2 cm) in XY table coordinates
2019-04-26 16:17:31,353 Moving XY table to position (Xtable=95.5 cm, Ytable=74.2 cm)
2019-04-26 16:17:31,353 Selecting XY table position: 95.5, 74.2
2019-04-26 16:17:31,357 Moving to next XY table position
2019-04-26 16:17:31,359 Waiting for XY table to be busy...
2019-04-26 16:17:32,216 XY table busy state changed to: True
2019-04-26 16:17:32,218 XY table IS busy
2019-04-26 16:17:32,218 Waiting for XY table to be idle...
2019-04-26 16:17:49,218 XY table busy state changed to: False
2019-04-26 16:17:49,220 XY table is NOT busy
2019-04-26 16:17:49,224 Current position: (X=95.46 cm, Y=74.15 cm) in XY table coordinates
2019-04-26 16:17:49,228 Distance between expected and actual positions: 0.00 cm
2019-04-26 16:17:52,231 Starting SPE flasher
2019-04-26 16:17:52,231 Starting flashes...
2019-04-26 16:17:52,231 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:18:13,290 Stopping SPE flasher
2019-04-26 16:18:13,290 Stopping flashes...
2019-04-26 16:18:13,291 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:18:14,341 Triggering TIB by slow control
2019-04-26 16:18:14,341 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:18:14,344 Moving XY table to position 5: module 114
2019-04-26 16:18:14,355 Module 114 is located at (X=-11.5 cm, Y=6.6 cm) in camera coordinates
2019-04-26 16:18:14,356 Module 114 is located at (X=95.5 cm, Y=100.6 cm) in XY table coordinates
2019-04-26 16:18:14,356 Moving XY table to position (Xtable=95.5 cm, Ytable=100.6 cm)
2019-04-26 16:18:14,356 Selecting XY table position: 95.5, 100.6
2019-04-26 16:18:14,360 Moving to next XY table position
2019-04-26 16:18:14,361 Waiting for XY table to be busy...
2019-04-26 16:18:15,221 XY table busy state changed to: True
2019-04-26 16:18:15,223 XY table IS busy
2019-04-26 16:18:15,224 Waiting for XY table to be idle...
2019-04-26 16:18:32,222 XY table busy state changed to: False
2019-04-26 16:18:32,225 XY table is NOT busy
2019-04-26 16:18:32,229 Current position: (X=95.46 cm, Y=100.61 cm) in XY table coordinates
2019-04-26 16:18:32,233 Distance between expected and actual positions: 0.00 cm
2019-04-26 16:18:35,236 Starting SPE flasher
2019-04-26 16:18:35,236 Starting flashes...
2019-04-26 16:18:35,236 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:18:56,307 Stopping SPE flasher
2019-04-26 16:18:56,307 Stopping flashes...
2019-04-26 16:18:56,307 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:18:57,358 Triggering TIB by slow control
2019-04-26 16:18:57,358 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:18:57,361 Moving XY table to position 6: module 112
2019-04-26 16:18:57,372 Module 112 is located at (X=-11.5 cm, Y=33.1 cm) in camera coordinates
2019-04-26 16:18:57,372 Module 112 is located at (X=95.5 cm, Y=127.1 cm) in XY table coordinates
2019-04-26 16:18:57,372 Moving XY table to position (Xtable=95.5 cm, Ytable=127.1 cm)
2019-04-26 16:18:57,372 Selecting XY table position: 95.5, 127.1
2019-04-26 16:18:57,376 Moving to next XY table position
2019-04-26 16:18:57,378 Waiting for XY table to be busy...
2019-04-26 16:18:58,223 XY table busy state changed to: True
2019-04-26 16:18:58,225 XY table IS busy
2019-04-26 16:18:58,225 Waiting for XY table to be idle...
2019-04-26 16:19:15,223 XY table busy state changed to: False
2019-04-26 16:19:15,225 XY table is NOT busy
2019-04-26 16:19:15,229 Current position: (X=95.46 cm, Y=127.07 cm) in XY table coordinates
2019-04-26 16:19:15,233 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:19:18,235 Starting SPE flasher
2019-04-26 16:19:18,235 Starting flashes...
2019-04-26 16:19:18,235 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:19:39,303 Stopping SPE flasher
2019-04-26 16:19:39,303 Stopping flashes...
2019-04-26 16:19:39,303 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:19:40,353 Triggering TIB by slow control
2019-04-26 16:19:40,354 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:19:40,357 Moving XY table to position 7: module 146
2019-04-26 16:19:40,367 Module 146 is located at (X=11.5 cm, Y=46.3 cm) in camera coordinates
2019-04-26 16:19:40,368 Module 146 is located at (X=72.5 cm, Y=140.3 cm) in XY table coordinates
2019-04-26 16:19:40,368 Moving XY table to position (Xtable=72.5 cm, Ytable=140.3 cm)
2019-04-26 16:19:40,368 Selecting XY table position: 72.5, 140.3
2019-04-26 16:19:40,372 Moving to next XY table position
2019-04-26 16:19:40,374 Waiting for XY table to be busy...
2019-04-26 16:19:41,225 XY table busy state changed to: True
2019-04-26 16:19:41,228 XY table IS busy
2019-04-26 16:19:41,228 Waiting for XY table to be idle...
2019-04-26 16:20:01,225 XY table busy state changed to: False
2019-04-26 16:20:01,227 XY table is NOT busy
2019-04-26 16:20:01,232 Current position: (X=72.54 cm, Y=140.29 cm) in XY table coordinates
2019-04-26 16:20:01,236 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:20:04,237 Starting SPE flasher
2019-04-26 16:20:04,237 Starting flashes...
2019-04-26 16:20:04,237 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:20:25,308 Stopping SPE flasher
2019-04-26 16:20:25,308 Stopping flashes...
2019-04-26 16:20:25,308 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:20:26,359 Triggering TIB by slow control
2019-04-26 16:20:26,359 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:20:26,362 Moving XY table to position 8: module 148
2019-04-26 16:20:26,373 Module 148 is located at (X=11.5 cm, Y=19.8 cm) in camera coordinates
2019-04-26 16:20:26,374 Module 148 is located at (X=72.5 cm, Y=113.8 cm) in XY table coordinates
2019-04-26 16:20:26,374 Moving XY table to position (Xtable=72.5 cm, Ytable=113.8 cm)
2019-04-26 16:20:26,374 Selecting XY table position: 72.5, 113.8
2019-04-26 16:20:26,378 Moving to next XY table position
2019-04-26 16:20:26,379 Waiting for XY table to be busy...
2019-04-26 16:20:27,225 XY table busy state changed to: True
2019-04-26 16:20:27,227 XY table IS busy
2019-04-26 16:20:27,227 Waiting for XY table to be idle...
2019-04-26 16:20:44,224 XY table busy state changed to: False
2019-04-26 16:20:44,227 XY table is NOT busy
2019-04-26 16:20:44,231 Current position: (X=72.54 cm, Y=113.85 cm) in XY table coordinates
2019-04-26 16:20:44,235 Distance between expected and actual positions: 0.00 cm
2019-04-26 16:20:47,238 Starting SPE flasher
2019-04-26 16:20:47,238 Starting flashes...
2019-04-26 16:20:47,238 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:21:08,307 Stopping SPE flasher
2019-04-26 16:21:08,307 Stopping flashes...
2019-04-26 16:21:08,307 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:21:09,358 Triggering TIB by slow control
2019-04-26 16:21:09,358 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:21:09,361 Moving XY table to position 9: module 150
2019-04-26 16:21:09,372 Module 150 is located at (X=11.5 cm, Y=-6.6 cm) in camera coordinates
2019-04-26 16:21:09,372 Module 150 is located at (X=72.5 cm, Y=87.4 cm) in XY table coordinates
2019-04-26 16:21:09,372 Moving XY table to position (Xtable=72.5 cm, Ytable=87.4 cm)
2019-04-26 16:21:09,373 Selecting XY table position: 72.5, 87.4
2019-04-26 16:21:09,377 Moving to next XY table position
2019-04-26 16:21:09,379 Waiting for XY table to be busy...
2019-04-26 16:21:10,227 XY table busy state changed to: True
2019-04-26 16:21:10,229 XY table IS busy
2019-04-26 16:21:10,229 Waiting for XY table to be idle...
2019-04-26 16:21:27,227 XY table busy state changed to: False
2019-04-26 16:21:27,229 XY table is NOT busy
2019-04-26 16:21:27,233 Current position: (X=72.54 cm, Y=87.39 cm) in XY table coordinates
2019-04-26 16:21:27,237 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:21:30,238 Starting SPE flasher
2019-04-26 16:21:30,238 Starting flashes...
2019-04-26 16:21:30,238 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:21:51,304 Stopping SPE flasher
2019-04-26 16:21:51,304 Stopping flashes...
2019-04-26 16:21:51,305 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:21:52,355 Triggering TIB by slow control
2019-04-26 16:21:52,356 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:21:52,359 Moving XY table to position 10: module 152
2019-04-26 16:21:52,370 Module 152 is located at (X=11.5 cm, Y=-33.1 cm) in camera coordinates
2019-04-26 16:21:52,370 Module 152 is located at (X=72.5 cm, Y=60.9 cm) in XY table coordinates
2019-04-26 16:21:52,370 Moving XY table to position (Xtable=72.5 cm, Ytable=60.9 cm)
2019-04-26 16:21:52,370 Selecting XY table position: 72.5, 60.9
2019-04-26 16:21:52,374 Moving to next XY table position
2019-04-26 16:21:52,376 Waiting for XY table to be busy...
2019-04-26 16:21:53,230 XY table busy state changed to: True
2019-04-26 16:21:53,233 XY table IS busy
2019-04-26 16:21:53,233 Waiting for XY table to be idle...
2019-04-26 16:22:10,233 XY table busy state changed to: False
2019-04-26 16:22:10,235 XY table is NOT busy
2019-04-26 16:22:10,239 Current position: (X=72.54 cm, Y=60.93 cm) in XY table coordinates
2019-04-26 16:22:10,243 Distance between expected and actual positions: 0.00 cm
2019-04-26 16:22:13,245 Starting SPE flasher
2019-04-26 16:22:13,246 Starting flashes...
2019-04-26 16:22:13,246 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:22:34,315 Stopping SPE flasher
2019-04-26 16:22:34,316 Stopping flashes...
2019-04-26 16:22:34,316 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:22:35,366 Triggering TIB by slow control
2019-04-26 16:22:35,367 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:22:35,370 Moving XY table to position 11: module 185
2019-04-26 16:22:35,380 Module 185 is located at (X=34.4 cm, Y=-19.8 cm) in camera coordinates
2019-04-26 16:22:35,381 Module 185 is located at (X=49.6 cm, Y=74.2 cm) in XY table coordinates
2019-04-26 16:22:35,381 Moving XY table to position (Xtable=49.6 cm, Ytable=74.2 cm)
2019-04-26 16:22:35,381 Selecting XY table position: 49.6, 74.2
2019-04-26 16:22:35,385 Moving to next XY table position
2019-04-26 16:22:35,387 Waiting for XY table to be busy...
2019-04-26 16:22:36,236 XY table busy state changed to: True
2019-04-26 16:22:36,239 XY table IS busy
2019-04-26 16:22:36,239 Waiting for XY table to be idle...
2019-04-26 16:22:56,240 XY table busy state changed to: False
2019-04-26 16:22:56,242 XY table is NOT busy
2019-04-26 16:22:56,246 Current position: (X=49.63 cm, Y=74.15 cm) in XY table coordinates
2019-04-26 16:22:56,250 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:22:59,253 Starting SPE flasher
2019-04-26 16:22:59,253 Starting flashes...
2019-04-26 16:22:59,253 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:23:20,323 Stopping SPE flasher
2019-04-26 16:23:20,323 Stopping flashes...
2019-04-26 16:23:20,323 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:23:21,374 Triggering TIB by slow control
2019-04-26 16:23:21,374 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:23:21,377 Moving XY table to position 12: module 183
2019-04-26 16:23:21,388 Module 183 is located at (X=34.4 cm, Y=6.6 cm) in camera coordinates
2019-04-26 16:23:21,389 Module 183 is located at (X=49.6 cm, Y=100.6 cm) in XY table coordinates
2019-04-26 16:23:21,389 Moving XY table to position (Xtable=49.6 cm, Ytable=100.6 cm)
2019-04-26 16:23:21,389 Selecting XY table position: 49.6, 100.6
2019-04-26 16:23:21,393 Moving to next XY table position
2019-04-26 16:23:21,395 Waiting for XY table to be busy...
2019-04-26 16:23:22,241 XY table busy state changed to: True
2019-04-26 16:23:22,243 XY table IS busy
2019-04-26 16:23:22,244 Waiting for XY table to be idle...
2019-04-26 16:23:39,246 XY table busy state changed to: False
2019-04-26 16:23:39,249 XY table is NOT busy
2019-04-26 16:23:39,253 Current position: (X=49.63 cm, Y=100.61 cm) in XY table coordinates
2019-04-26 16:23:39,257 Distance between expected and actual positions: 0.00 cm
2019-04-26 16:23:42,260 Starting SPE flasher
2019-04-26 16:23:42,260 Starting flashes...
2019-04-26 16:23:42,260 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:24:03,331 Stopping SPE flasher
2019-04-26 16:24:03,331 Stopping flashes...
2019-04-26 16:24:03,331 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:24:04,381 Triggering TIB by slow control
2019-04-26 16:24:04,382 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:24:04,385 Moving XY table to position 13: module 181
2019-04-26 16:24:04,396 Module 181 is located at (X=34.4 cm, Y=33.1 cm) in camera coordinates
2019-04-26 16:24:04,396 Module 181 is located at (X=49.6 cm, Y=127.1 cm) in XY table coordinates
2019-04-26 16:24:04,396 Moving XY table to position (Xtable=49.6 cm, Ytable=127.1 cm)
2019-04-26 16:24:04,396 Selecting XY table position: 49.6, 127.1
2019-04-26 16:24:04,400 Moving to next XY table position
2019-04-26 16:24:04,402 Waiting for XY table to be busy...
2019-04-26 16:24:05,246 XY table busy state changed to: True
2019-04-26 16:24:05,249 XY table IS busy
2019-04-26 16:24:05,249 Waiting for XY table to be idle...
2019-04-26 16:24:22,249 XY table busy state changed to: False
2019-04-26 16:24:22,252 XY table is NOT busy
2019-04-26 16:24:22,255 Current position: (X=49.63 cm, Y=127.07 cm) in XY table coordinates
2019-04-26 16:24:22,260 Distance between expected and actual positions: 0.01 cm
2019-04-26 16:24:25,262 Starting SPE flasher
2019-04-26 16:24:25,262 Starting flashes...
2019-04-26 16:24:25,262 Calling method NectarCAM.CalibrationBox.Start in object NectarCAM.CalibrationBox
2019-04-26 16:24:46,332 Stopping SPE flasher
2019-04-26 16:24:46,332 Stopping flashes...
2019-04-26 16:24:46,333 Calling method NectarCAM.CalibrationBox.Stop in object NectarCAM.CalibrationBox
2019-04-26 16:24:47,383 Triggering TIB by slow control
2019-04-26 16:24:47,383 Calling method Camera.TIB.LaunchSCTrigger in object Camera.TIB
2019-04-26 16:24:47,387 Moving white target to parking position
2019-04-26 16:24:47,389 Waiting for parked position...
2019-04-26 16:24:48,250 XY table busy state changed to: True
2019-04-26 16:25:22,254 XY table busy state changed to: False
2019-04-26 16:25:22,255 XY table parking state changed to: True
2019-04-26 16:25:22,257 XY table IS parked
16:13 - Checking for high voltage locked pixels...
16:13 - Checking for high voltage locked pixels...
16:14 - Checking for high voltage locked pixels...
16:14 - Checking for high voltage locked pixels...
16:15 - Status: TibState.Running ConnectionStatus: True
16:15 - Alarms: AlarmVector.ReadError
16:15 - Temperature: 40.75
16:15 - Local camera rate: 0.0 Hz
16:15 - Stereo trigger rate: 0.0 Hz
16:15 - SPE trigger rate: 100.0 Hz
16:15 - Calibration trigger rate: 0.0 Hz
16:15 - Software trigger rate: 0.0 Hz
16:15 - Pedestal trigger rate: 0.0 Hz
16:15 - Collected trigger rate: 100.0 Hz
16:15 - Busy rate: 0.0 Hz
16:15 - Camera trigger rate: 100.0 Hz
16:15 - Checking for high voltage locked pixels...
16:15 - Checking for high voltage locked pixels...
16:16 - Status: TibState.Running ConnectionStatus: True
16:16 - Alarms: AlarmVector.ReadError
16:16 - Temperature: 40.81
16:16 - Local camera rate: 0.0 Hz
16:16 - Stereo trigger rate: 0.0 Hz
16:16 - SPE trigger rate: 0.0 Hz
16:16 - Calibration trigger rate: 0.0 Hz
16:16 - Software trigger rate: 0.0 Hz
16:16 - Pedestal trigger rate: 0.0 Hz
16:16 - Collected trigger rate: 0.0 Hz
16:16 - Busy rate: 0.0 Hz
16:16 - Camera trigger rate: 0.0 Hz
16:16 - Checking for high voltage locked pixels...
16:16 - Checking for high voltage locked pixels...
16:17 - Checking for high voltage locked pixels...
16:17 - Checking for high voltage locked pixels...
16:18 - Checking for high voltage locked pixels...
16:18 - Checking for high voltage locked pixels...
16:19 - Checking for high voltage locked pixels...
16:19 - Checking for high voltage locked pixels...
16:20 - Checking for high voltage locked pixels...
16:20 - Checking for high voltage locked pixels...
16:21 - Checking for high voltage locked pixels...
16:21 - Checking for high voltage locked pixels...
16:22 - Checking for high voltage locked pixels...
16:22 - Checking for high voltage locked pixels...
16:23 - Checking for high voltage locked pixels...
16:23 - Checking for high voltage locked pixels...
16:24 - Checking for high voltage locked pixels...
16:24 - Checking for high voltage locked pixels...
16:25 - Checking for high voltage locked pixels...
16:25 - Stopping TIB...
16:25 - Status: TibState.Running
16:25 - Alarms: AlarmVector.ReadError
16:25 - Connection status: True
16:25 - Disabling trigger
16:25 - Disabling PPS
16:25 - Status: TibState.PpsStopped
16:25 - Alarms: AlarmVector.ReadError
16:25 - Connection status: True
16:25 - Closing TIB connection to camera server
16:25 - Status: TibState.PpsStopped
16:25 - Alarms: AlarmVector.ReadError
16:25 - Connection status: False
16:25 - Run duration: 0:12:39
16:25 - Local camera triggers: 0
16:25 - Slow control triggers: 14
16:25 - Single photo-electron triggers: 29495
16:25 - Calibration triggers: 0
16:25 - Software triggers from UCTS: 0
16:25 - Pedestal triggers: 0
16:25 - Collected input triggers: 29509
16:25 - Busy triggers: 0
16:25 - Camera event triggers sent to clusters: 29509
16:25 - Checking for high voltage locked pixels...